Smith & Noble Marrakesh Hardware User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Wall Mount
Single Bay Rod Set
Marrakesh
Hardware

2
800.248.8888
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Wall
Mount Single Bay Rod Set ....................4
Step 2 - Mounting the Brackets ........................ 5 - 6
Step 3 - Rod Connectors .................................7
Step 4 - Attaching the Finials & Rings ................... 8 - 9
Step 5 - Securing Rod to Brackets ........................10
Accessories - Baton/Wand ..................................11
Accessories - Tiebacks ...................................12-13
Care & Cleaning ...........................................14
Warranty ..........................................Back Cover
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
this guide. If you encounter any difculties or questions,
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
strongly doubt it), we want any potential returns to be a
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Marrakesh Single Bay Rod Set
FINIALFINIAL RODROD ROD
CORNER/
ELBOW
BRACKET
CORNER/
ELBOW
BRACKET
MOUNTING
BRACKETS MOUNTING BRACKETS
BYPASS
CENTER
BRACKET
BYPASS
CENTER
BRACKET
MOUNTING
BRACKETS
ROD QTY BRACKET QTY ELBOWS QTY ROD WIDTH
1 2 2 12"— 48"
1 3 2 48¹⁄4"—72"
1 4 2 72¹⁄4"—96"
2 5 2 96¹⁄4"—144"
2 7 2 144¹⁄4"—192"
3 7 2 192¹⁄4"—216"
3 9 2 216¹⁄4"—288"
411 2288¹⁄4"—360"
413 2360¹⁄4"—384"
Before you begin, check the accompanying diagram to make sure you have all the parts you need.
You’ll need to make sure the surface you intend to install your hardware is sturdy enough to
accommodate the brackets. If you’re screwing directly
into a surface this means locating wood studs that are
strong enough to securely bond with the included
screws. Otherwise, you’ll need to use a secure fastener
(as illustrated) but please note this piece is not included.
WALLBOARD OR PLASTER: Hollow wall applications: Use a secure fastener designed
speci cally for this purpose.
METAL: Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE: Use a masonry drill and surface-speci c plugs, anchors, or
screws.When selecting a fastener be sure it’s designed to support the weight of the product being
installed (if you’re not sure, either give us a call or ask a professional at your local hardware store).
Once obtained, follow the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE: Pencil, screwdriver, ¼" nut driver,
level, and a drill with a
7⁄64
"drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the screws
are too tight this may cause the screw itself to break off in the wall or window frame.
Parts & Tools
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
SCREWS CORNER BRACKET WALL MOUNT BRACKET
ALLEN WRENCHES
SET SCREWS
RINGS &
C-RINGS (OPTIONAL)
BYPASS CENTER BRACKET
(OPTIONAL)
PENCIL & SCREWDRIVER
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)

56
smithandnoble.com 800.248.8888
Mounting the Brackets
Place the panel on the left rod. To
ensure it drapes at the correct length,
hold it up to the spot you wish to
install it; this will allow you to raise or
lower your treatment as desired. After
you’ve located the ideal location, use
a pencil to mark the wall where the
top of the rod is resting. Repeat on the
other two sides.
Remove the panel from the rods and
then center the rods over the window
opening at the desired height. Using
the pencil, mark where the ends of each
rod are positioned; if you’re using a
center bracket, note the middle point
between these two spots as well. If
you have more than one center bracket
spread these evenly between the two
end brackets and center point. If you
have a spliced rod, mark where that
splice is as well since you will need to
add a bracket at that point as well.
Measure 2” inward from the marks
you’ve made on both ends and mark
those spots. This is where the brackets
will be installed.
Place brackets level against wall at the
marked spots. Using a pencil, lightly draw
a circle around the base of the bracket
onto wall (See Figure A). Check to make
sure the circles are level & aligned with
each other.
Mounting the Brackets
Remove mounting plate and center
it inside of the circle outline on wall.
Mark the screw hole locations for all
brackets (See Figure B).
Attach the metal mounting plate to
the wall, aligning the holes in the
plate with the marks made in the
previous step (See Figure B).
Be sure and attach the plate to the
wall with the appropriate mounting
hardware. (It is always recommended
to try and attach to the wood studs
inside the wall. Where this is not
possible please use a wall anchor
suitable to carry the weight of your
hardware selection as well as your
draperies and any accessories.)
If using plastic expansion anchors,
pre-drill holes using 3/16" drill bit. If
drilling directly into a stud or wood
trim, pre-drill holes with 3/32" drill bit.
Screw on the decorative portion of
the bracket to the mounting base
until it is tight and the open side of
bracket faces up to the ceiling. If the
cup does not end facing up, loosen
the base screw to adjust & tighten
back up. Repeat these steps for all
brackets (See Figure C).
STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS
CENTER ROD
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.
MOUNTING
PLATE
BACK PLATE
X
X
X
X
X
FIGURE A
FIGURE C
MOUNTING
PLATE DECORATIVE PORTION OPEN SIDE(CUP) OF BRACKET
FACES UP
BASE SCREW

78
smithandnoble.com 800.248.8888
For treatments using rings
Attach the finial to one end of the rod
by sliding it on and attaching it using
the set screw (1).
Place the required number of rings on
the rod, and then cap the opposite end
with the elbow and attach it using the
set screw. When placing the rod on the
bracket, if Drapery is opening from
the center, leave one ring between the
finial/elbow and bracket on each side.
If the drapery is opening from one side
only, put the ring between the finial/
elbow and the bracket on the opposite
side of where you are opening from
(2).This will prevent drapery to be
pulled all the way to one side or the
other when opening and closing it.
Cont. on pg 9
Depending on your order, you may
have received a rod connector. A rod
connector is the short piece of metal
tubing placed inside each end of the
rods in a multi-segment system to
join them together.
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ATTACHING THE FINIALS & RINGS
STEP 2:
Now slide the second rod segment
over the exposed end of the
connector, making sure there is no
gap between the two segments.
STEP 1:
On the open end of one-rod segment,
slide the connector halfway inside,
leaving the other half exposed.
ROD CONNECTOR
ROD
SEGMENT
ROD
SEGMENT
ROD
CONNECTOR
1
2
ATTACH FINIAL
PLACE ONE RING
BETWEEN FINIAL
AND BRACKET

910
smithandnoble.com 800.248.8888
STEP 5 - SECURING ROD TO BRACKETSSTEP 4 - ATTACHING THE FINIALS & RINGS
Once the rod has been placed on the
brackets, secure the rod in place by
tightening the bracket set screw with
the allen wrench provided.
Please note: If your rod set comes with
bypass center support brackets these
do not have a set screw. Just rest the
rod on the bracket for support.
Continue by attaching the middle rod
to the elbow on the left side (3) and
tightening the set screw on the elbow.
Place the required number of rings on
the rod, and then cap the opposite
end with the other elbow and attach it
using the set screw (4).
When placing the rod on the bracket,
if drapery is opening from the center,
leave one ring between the finial/
elbow and bracket on each side. If the
drapery is opening from one side only,
put the ring between the finial/elbow
and the bracket on the opposite side of
where you are opening from (2). This
will prevent drapery to be pulled all
the way to one side or the other when
opening and closing it.
Attach the finial to one end of the
3rd rod by sliding it on and attaching
it using the set screw (5). Place the
required number of rings on the rod,
and then cap the opposite end with the
elbow attached to the middle rod and
attach it using the set screw.
When placing the rod on the bracket,
if drapery is opening from the center,
leave one ring between the finial/elbow
and bracket on each side. If the drapery
is opening from one side only, put the
ring between the finial/elbow and the
bracket on the opposite side of where
you are opening from (2).This will
prevent drapery to be pulled all the way
to one side or the other when opening
and closing it.
For treatments without rings
Attach the finial to one end of the rod by
sliding it on and attaching it using the set
screw (1).Position the drapery panels on
rod, and then cap the opposite end with
the elbow (3).
Position the drapery panels on the
middle rod, and then cap the Left end
with the elbow attached to the left rod
using the set screw on the elbow (3).
Attach the finial to one end of the 3rd
rod by sliding it on and attaching it using
the set screw (5). Position the drapery
panels on rod, and then cap the opposite
end with the elbow on the middle rod
using the set screw on the elbow.
1
34
5
TIGHTEN
SET SCREW
TIGHTEN
SET SCREW
BYPASS SUPPORT
BRACKET

11 12
smithandnoble.com 800.248.8888
ACCESSORIES ACCESSORIES
Tiebacks (optional)
STEP 1
In order to locate where to install your
tiebacks, measure the height of the
window and divide this by two. Using
the previous calculation, mark that spot
on the wall with a pencil.
To ensure you like the way the panel
drapes, gather one side and sweep
it over to the approximate proposed
location. Once you’re sure the tieback is
in the perfect location, use your pencil to
mark the spot to install it.
Measure the distance from the bottom
or top of the window to the tieback to
mark the other side and ensure they’re
even.
Now hold the tieback hardware on the
wall at the desired location and rest
a level above it, adjusting it until it’s
straight.
Cont. on pg 13
Baton/Wand (optional)
After your hardware is installed, attach
the baton to the eyelet of the first ring
by the clip.
BATON/
WAND
CLIP
EYELET
DRAPERY
RING
Push clip through
the eyelet of the
drapery clip
Baton/Wand
X
Figure A

13 14
smithandnoble.com 800.248.8888
ACCESSORIES CARE & CLEANING
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.
To Dust: Use soft, clean cloth.
Tiebacks (optional)
STEP 2:
Place tieback level against wall in
desired locations and lightly draw a
circle around the base of the tieback
onto wall (see Figure A).
Remove tieback post and cover from
mounting plate.
Center mounting plate inside of the
circle outline on wall.
Attach the metal mounting plate to the
wall using the appropriate mounting
hardware.
Place cover over the mounting plate.
Thread tieback post onto the mounting
plate (see Figure B).
TIEBACK POST
MEDALLION
MOUNTING
PLATE
Figure A
POSTS
COVER
PLATE
MOUNTING
PLATE
TIEBACK
MEDALLION
Figure B

© 2019 Smith & Noble Home, Inc. All Rights Reserved SN0519
Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to the
original owner, requires a proof of purchase (hang on to your receipt!) and
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.