Sony Super HAD CCD II SSC-FM531 User manual

WARNING
To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquid, such as vases, shall be placed on the apparatus.
警告
为减少⽕灾或电击危险，请勿让本设备受到⾬淋或
受潮。
为防⽌触电严禁拆开机壳，维修请咨询具备资格⼈
⼠。
设备不要受到滴水或水溅，不要将盛满液体的花瓶等物品放在设备
上。
WARNING
This installation should be made by a qualified service person and should
conform to all local codes.
警告
本安装应该由有资格的服务⼈员进⾏，并须符合所有当地法规规
定。
IMPORTANT
The nameplate is located on the bottom.
重要
设备铭牌位于底部。
警告
此为A级产品。在生活环境中，该产品可能会造成无线电干扰。
在这种情况下，可能需要用户对干扰采取切实可⾏的措施。
ATTENTION
The electromagnetic fields at the specific frequencies may influence the picture
of this unit.
注意
某些特定频率的电磁场可能会干涉本装置的图像。
关于旧产品的处理
请不要将旧的产品与一般的生活垃圾一同弃置。
正确弃置旧的产品有助于避免对环境和⼈类健康造成潜在的负面影
响。
具体处理方法请遵循当地的规章制度。
中文
使用本机前，请仔细阅读本使用手册并妥善保存以备日后参考。
特性
这是一款采用1/3型Super HAD CCD II™*的半球型摄像机。具有以下
特点：
手动设定摄像机方向-水平、垂直和旋转。

Vari-focal auto iris镜头作为标准配置。镜头的焦距从2.8 mm

至10.5 mm。
高分辨率和高灵敏度。

使用DynaViewSX技术的宽动态范围。

降噪。

日/夜功能可进⾏彩色/单色模式切换。

24V交流/12V直流电源系统。

线路锁定功能（24V交流）。

使用英文和中文画面菜单进⾏轻松设定。

* Super HAD CCD II™是Sony Corporation的商标。
使用须知
操作或存放场所
请勿拍摄⾮常亮的物体（灯光、阳光等）。避免在以下位置使用或
存放摄像机，否则会导致故障。
极热或极冷的地方（操作温度：-10℃至+50℃）

长时间暴露于直射阳光下，或者靠近热源（⽐如加热器）的地方

靠近强磁源的位置

靠近无线电或电视发射器等强电磁辐射源的地方

易于受到强⼒振动或撞击的地方

潮湿或有灰尘的地方

暴露于⾬水的地方

受到荧光灯或窗户反射光影响的地方

在不稳定光线的下面（图像会闪烁。）

通风
为了避免热量积蓄，不要阻挡摄像机附近的通风。
运送
当运送摄像机时，重新以出⼚时的包装进⾏包装，或用同等品质的
材质包装。
清洁
用吹灰器清除镜头灰尘。

使用柔软、干燥的布清洁摄像机的外表面。要清除顽固的污渍，

请用少量清洁剂蘸湿软布，然后擦干即可。
不要使用酒精、苯或稀释剂等挥发性溶剂，这些物质可能会破坏

表面光洁度。
关于激光束
激光束可能会损坏CCD。若拍摄含有激光束的场面，请注意不要让
激光束直接射入摄像机的镜头。
注
如果在电源质量差的操作环境下使用线路锁定功能，监视器图像可
能失真。
摄像机在使用过程中出现的任何问题请与您的Sony经销商联系。
各部件位置和功能
侧⾯ 
 电源电缆
将电源电缆连接至24 V交流电源或12 V直流电源（ ）。连接器端为
快速断线型，可固定任一端连接器上的电缆。
 BNC电缆
将BNC电缆连接至监视器或视频装置（ ）。
 I/O电缆
将I/O电缆连接至外部控制信号。
白色：EXTERNAL CTRL OUT：选择彩色模式时在本端子和COM之间输
出H (+5 V)；选择黑白模式时输出L (0 V)。
黑色：COM：白色电线和红色电线共用。
红色：EXTERNAL CTRL IN：选择彩色模式时在本端子和COM之间应用
H (+5 V)；选择黑白模式时应用L (0 V)。
注意
不使用时，使I/O电缆的三个导线端绝缘以免短路。
 间隙调整法兰（排出型）
若电缆在安装表面与摄像机之间产生了间隙，请用镊子折断排出法
兰并将电缆穿过开口处。有两个排出法兰。
 变焦杆
拨动此杆可调整视线角度。此杆本身是一螺杆，拧紧此杆以将它锁
定在其位置。
 聚焦杆
拨动此杆可调整焦距长度。此杆本身是一螺杆，拧紧此杆以将它锁
定在其位置。
内部 
 摄像机安装孔 (2个位置)
用螺丝（未附带）通过这些安装孔将摄像机安装在天花板上或墙
上。
 MENU/ENTER按钮
用于菜单操作。按此按钮来显示菜单或确认设定。
向或方向按使光标上移或下移。向或方向按以改变菜单设定。
有关使用详情，请参阅附送的“菜单操作”手册。
 PHASE调节螺丝
使用此螺丝以调整为LL所同步的各摄像机的垂直相位。
 MONITOR连接器
将监视器电缆连接至此连接器。在监视器上观看图像时可以调节摄
像机。调节摄像机后，请拔下电缆。
连接电缆
1 将BNC电缆连接至监视器或视频装置（参见图  ）。
2 将电源电缆连接至电源插座（24 V交流电源/12 V直流电源）（参
见图  ）。
注意
为防止发生短路，在连接电源电缆时，请勿使电源电缆裸露端相互
接触。
准备
安装前 
确定摄像机拍摄方向后，用附带的模板制作所需的电缆连接孔
（ø 30 mm）。然后确定两个安装孔的位置以安装摄像机。
注意
“FRONT SIDE”标记（）表示SONY标识在产品上的方向。决定摄
像机的拍摄方向后，请将SONY标识转向拍摄方向，即，让“FRONT
SIDE”标记与SONY标识的方向相同。将摄像机安装在墙壁（⾮天花
板）上时，请让“FRONT SIDE”标记朝向下方。
安装螺丝
底座带有两个ø4.5 mm的安装孔。使用螺丝通过两个83.5 mm的安装
孔将底座安装在天花板或墙上。
根据安装位置及其材料的不同，所需的安装螺丝也有所不同。（安
装螺丝未附带。）
钢制墙壁或天花板：使用M4螺栓和螺⺟。
⽊制墙壁或天花板：使用M4⾃攻螺丝。面板厚度必须为15 mm或以
上。
⽔泥墙壁：使用适用于水泥墙壁的锚、螺栓和楔子。
接线盒：使用与接线盒上的孔相匹配的螺丝。
警告
根据安装位置及其材料的不同，所需的安装螺钉也有所不同。如果您
没有使用合适的安装螺钉将摄像机安装牢靠，摄像机有可能坠落。
（接反⾯）
English
Before operating the unit, please read this manual thoroughly and retain it for
future reference.
Features
This is a dome-shaped color video camera for which the 1/3 type Super HAD
CCD II™* has been adopted. It has the following features:
Manual setting of the camera direction - panning, tilting and rotating.

Vari-focal auto iris lens as standard equipment. The focal length of the lens is

from 2.8 mm to 10.5 mm.
High resolution and high sensitivity.

Wide dynamic range using DynaViewSX technology.

Noise Reduction.

Day/Night function allowing color/monochrome mode switching.

AC 24V/DC 12V power supply system.

Line Lock function (AC 24V).

Easy setup using on-screen menu by English and Chinese language.

* Super HAD CCD II™is a trademark of Sony Corporation.
Notes on Use
Operating or storage location
Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,
avoid operating or storing the camera in the following locations, as these can be
a cause of a malfunction.
Extremely hot or cold places (Operating temperature: –10°C to +50°C [14°F to

122°F])
Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,

near heaters)
Close to sources of strong magnetism

Close to sources of powerful electromagnetic radiation, such as radios or TV

transmitters
Locations subject to vibration or shock

Humid or dusty locations

Locations exposed to rain

Locations under the influence of fluorescent light or reflection of a window

Under an unsteady light (the image will flicker.)

Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
When transporting the camera, repack it as originally packed at the factory or in
materials of equal quality.
Cleaning
Use a blower to remove dust from the lens.

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn

stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may

damage the surface finishes.
Note on laser beams
Laser beams may damage the CCDs. If you shoot a scene that includes a laser
beam, be careful not to let a laser beam become directed into the lens of the
camera.
Note
If you use the Line Lock function in an operating environment where power quality is
poor, the monitor image may be distorted.
In the event of any problems with the operation of the camera, contact your
Sony dealer.
Location and Function of Part
Side 
Power cable
Connect the power cable to AC 24 V or DC 12 V ( ). The connector tip is a
quick-disconnect type. You can screw the cables in either connectors of the tip.
BNC cable
Connect the BNC cable to a monitor or video device ( ).
I/O cable
Connect the I/O cable to external control signals.
White: EXTERNAL CTRL OUT: H (+5 V) is output between this terminal and COM
when the color mode is selected; L (0 V) is output when the B/W mode is
selected.
Black: COM: common to the white wire and the red wire.
Red: EXTERNAL CTRL IN: When H (+5 V) is applied between this terminal and
COM, the color mode is selected; when L (0 V) is applied, B/W mode is selected.
Note
Insulate the three wire ends of the I/O cable to avoid a short when not in use.
Gap adjustment flange (knockout type)
If the cable creates a gap between the installation surface and the camera, break
off the knockout flange by using nippers and insert the cable through the
opening. There are two knockouts.
Zoom lever
Move this lever to adjust the angle of view. Tighten its screw to fix its position.
Focus lever
Move this lever to adjust the focal length. Tighten its screw to fix its position.
Inside 
Camera installation holes (2 positions)
Install the camera onto the ceiling or wall with the screws (not supplied) inserted
through these holes.
MENU/ENTER button
Use for menu operation. Press this button to display the menu or confirm
settings.
Press towards or to move the cursor up or down. Press towards or to
change a menu setting.
For details on use, refer to the supplied “Menu Operations” manual.
PHASE adjustment screw
Use this screw to adjust the vertical phase of cameras synchronized by LL.
MONITOR connector
Connect the monitor cable to this connector. You can adjust the camera while
looking at the image on the monitor. After adjusting the camera, disconnect the
cable.
Connecting the Cables
1Connect the BNC cable to a monitor or video device (see figure ).
2Connect the power cable to the power supply (AC 24 V/DC 12 V)
(see figure ).
Caution
When you connect the power cable, be sure that the exposed ends of the power cable
do not touch each other to prevent a short circuit.
Preparations
Before Installation 
After deciding the direction in which the camera will shoot, make the required
hole (ø30 mm (1 3/16 inches)) for the connecting cables using the supplied
template. Then decide the two mounting hole positions to install the camera
unit.
Note
The “FRONT SIDE” mark () indicates the direction of the SONY logo on the product.
After deciding the direction in which the camera will shoot, turn the SONY logo
towards the shoot direction. “FRONT SIDE” mark faces in the same direction as the
SONY logo. When installing the camera on a wall (not on a ceiling), face the “FRONT
SIDE” mark downward.
Mounting screws
The base bracket is provided with two ø4.5 mm (3/16 inch) mounting holes. Install
the bracket on a ceiling or wall with screws through two 83.5 mm (3 9/32 inches)
mounting holes:
The required mounting screws differ depending on the installation location and
its material. (Mounting screws are not supplied.)
Steel wall or ceiling: Use M4 bolts and nuts.
Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be
15 mm (5/8inch) or more.
Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.
Junction box: Use screws to match the holes on the junction box.
WARNING
The required mounting screws differ depending on the installation location and its
material. If you do not secure the camera with the appropriate mounting screws, the
camera may fall off.
(continued on the reverse side)
A






B




C
83.5 (3 9/32)
Unit : mm (inches)/单位：mm
Operating Instructions
使用手册
Color Video Camera
半球型摄像机
4-300-099-22(1)
© 2011 Sony Corporation Printed in China
SSC-FM531/FM561

D
Screw (not
supplied)/
螺丝（未附
带）
Ceiling/天花板
Rope (not supplied)/
防坠绳（未附带）
E
–1
Dome casing/圆顶罩
–2
Dome slit/
开口罩
F
Pan adjuster/
⽔平调节器
2
3
b
a
c
G
–1,2
–3
Base bracket/底座
Slot/插槽
Mark/标记
H
Bottom/底部
4.5 (3/16)
83.5 (3 9/32)
Side/边侧
86.5 (31/₂)
121.6 (4 7/₈)
Unit : mm (inches)/单位：mm
English
Attaching the fall-prevention rope 
When you install the camera on a ceiling or a high location, be sure to attach a
fall-prevention rope (not supplied) to prevent the camera from falling. Thread
the fall-prevention rope through the hole on the camera as in the illustration,
and then fix it to the junction box on the ceiling or wall with a screw (not
supplied).
For details about the fall-prevention rope, please consult the store of purchase or
an authorized Sony dealer.
Installation
WARNING
If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.
If you install the camera at a height, ensure that the installation location and

its material are strong enough to withstand a weight of 15 kg (33 lb 1.1 oz) or
more, and then install the camera securely. If the ceiling is not strong enough,
the camera may fall and cause serious injury.
To prevent the camera from falling, make sure to attach a rope (not supplied).

If you attach the camera to the ceiling, check periodically, at least once a year,

to ensure that the connection has not loosened. If conditions warrant, make
this periodic check more frequently.
Installing the Camera 
1Press the locking hook inward and meanwhile turn the dome casing
anticlockwise, and remove the dome casing from the camera unit.
2Press both sides inward to remove the dome slit.
3Attach the camera unit to the ceiling or wall with two mounting screws (not
supplied).
Note
If you cannot use a screwdriver to fix the mounting screws, turn the pan adjuster (see
figure ) clockwise or anticlockwise until the screw holes can be fully seen.
If you cannot screw the camera unit directly onto a ceiling or wall, or if you want to
make the camera less conspicuous, use the YT-ICB140 In-Ceiling Bracket (optional).
When mounting the camera with an In-Ceiling Bracket, fix screws at position on
both sides of the In-Ceiling Bracket, fix the spacer (supplied with In-Ceiling Bracket),
then fix the camera.
Adjusting the Camera Direction and Coverage 
1Turn the lens in the desired direction.
You can adjust the lens position by panning ( ), tilting ( ), or rotating
( ).
2Loosen the zoom lever and move it to the right or left to adjust the angle of
view.
When you have set the zoom lever to the desired position, tighten it to fix the
angle of view.
3Loosen the focus lever and move it to the right or left to adjust the focal
length.
When you have set the focus lever to the desired position, tighten it to fix the
focal length.
4Repeat steps 1to 3until the camera direction and coverage are determined.
Note
When adjusting the lens position, be sure that the “BOTTOM ” mark on the angle
adjuster is toward the floor. If the camera is installed with the “BOTTOM ” mark
toward the ceiling, the image will appear upside down.
Attaching the Dome Casing 
1Set the opening of the dome slit to face in the direction of the lens.
2Push the dome slit onto the camera until it clicks.
3Align the mark on the dome casing with the slot on the base bracket, and
turn the dome casing in the direction of arrow until it clicks. Then ensure the
camera unit is set tightly.
Typical CCD phenomenon
The following phenomena that may appear in images are specific to CCD
(Charge Coupled Device) image sensors. They do not indicate malfunctions.
White flecks
Although the CCD image sensors are produced with high-precision technologies,
fine white flecks may be generated on the screen in rare cases, caused by cosmic
rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
when operating at a high environmental temperature
when you have raised the gain (sensitivity)
when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or flashlight, is
being shot, vertical tails may be produced on the screen, or the image may
be distorted.
Monitor screen Vertical tails shown on the image
Bright object (e.g., strong spotlight,
strong reflected light, flashlight, the sun)
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or
flicker.
Specifications
Image device Interline transfer 1/3 type
Effective picture elements 976 (H) x 582 (V)
Focal length 2.8 mm - 10.5 mm
Maximum relative aperture F1.2
View angle SSC-FM531:
Horizontal: 99.5° (wide) - 27.4° (tele)
Vertical: 73.2° (wide) - 20.6° (tele)
SSC-/FM561:
Horizontal: 101.8° (wide) - 27.4° (tele)
Vertical: 73.7° (wide) - 20.6° (tele)
Minimum object distance 0.3 m
Signal system PAL color system
Synchronization system Internal/Line lock switchable
Horizontal resolution 650 lines (normal mode),
700 lines (sharp mode)
Minimum illumination SSC-FM531:
Color: 0.10 lx at F1.2 (50 IRE, AGC ON,
Turbo mode)
Color: 0.06 lx at F1.2 (30 IRE, AGC ON,
Turbo mode)
B/W: 0.07 lx at F1.2 (50 IRE, AGC ON, Turbo
mode)
B/W: 0.05 lx at F1.2 (30 IRE, AGC ON, Turbo
mode)
SSC-FM561:
Color: 0.10 lx at F1.2 (50 IRE, AGC ON,
Turbo mode)
Color: 0.06 lx at F1.2 (30 IRE, AGC ON,
Turbo mode)
B/W: 0.01 lx at F1.2 (50 IRE, AGC ON, Turbo
mode)
B/W: 0.006 lx at F1.2 (30 IRE, AGC ON,
Turbo mode)
Video output 1.0 Vp-p, 75 Ω, negative sync , BNC cabel
Video S/N 55 dB (AGC OFF, WEIGHT ON)
Dynamic range 75 dB typical
Electronic shutter 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000, 1/20000, 1/40000,
1/80000, 1/100000 (sec)
White balance ATW-PRO/ATW/3200K/5600K/MANUAL
Automatic gain control (AGC) OFF/NORMAL/TURBO/MANUAL
Monitor out RCA jack
Power supply
AC 24V (50 Hz)/DC 12 V
Power consumption 2.8 W
Operating temperature –10°C to +50°C (14°F to 122°F)
Storage temperature –40°C to +60°C (–40°F to +140°F)
Operating humidity 20% to 80%
Storage humidity 20% to 95%
Dimensions (diameter/height) ø121.6 mm × 86.5 mm (ø4 7/8inches ×
3 1/2inches)
Mass SSC-FM531: Approx. 320 g (11 oz)
SSC-FM561: Approx. 330 g (12 oz)
Supplied accessories Template (1)
Operating instructions (this document) (1)
Menu Operations (1)
Optional accessory YT-ICB140 In-Ceiling Bracket
Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
中文
安装防坠绳 
将摄像机安装在天花板或较高位置时，必须安装防坠绳（未附带），
以防止摄像机掉落。如图所示，将防坠绳穿过摄像机上的孔，然后用
螺丝（未附带）固定于天花板或墙上的接线盒。
有关防坠绳的详情，请向购买商店或授权Sony经销商咨询。
安装
警告
如果要将摄像机安装在墙壁或天花板等高处，请将安装工作委托

给有经验的承包商或安装⼈员。
如果将摄像机安装在高处，请确保安装位置及其材料足够稳固，

能够承受至少15公斤的重量，然后牢固安装摄像机。如果天花板
不够稳固，摄像机可能坠落并导致严重伤害事故。
为防止摄像机掉落，必须安装防坠绳（未附带）。

如果将摄像机安装在天花板上，请定期检查，每年至少一次，以

确保连接没有松动。如果条件允许，请更频繁定期检查。
安装摄像机 
1 向内按锁定钩，同时逆时针转动圆顶罩，然后从摄像机上取下圆
顶罩。
2 向内按两侧取下开口罩。
3 使用两颗安装螺丝（未附带）将摄像机安装到天花板或墙上。
注意
如果您无法使用螺丝刀固定安装螺丝，请顺时针或逆时针转动水平
调节器(参见图 ），直到螺丝孔完全露出。
如果您无法将摄像头直接拧入天花板或墙壁，或如果您想要摄像头
不是很显眼，请使用YT-ICB140天花板托架（选购）。
使用天花板托架安装摄像头时，请固定天花板托架周边 位置的
螺丝，固定垫片（天花板托架附送），然后固定摄像头。
调节摄像机的方向和范围 
1 按所需方向转动镜头。
可通过水平（ ）、垂直（ ）或旋转（ ）来调节镜头位置。
2 松开变焦杆并将它移至右侧或左侧，以调节视线角度。
将变焦杆设定至所需位置后，拧紧它以固定视线角度。
3 松开聚焦杆并将它移至右侧或左侧，以调节焦距长度。
将聚焦杆设定于所需位置后，请拧紧它以固定焦距长度。
4 重复步骤1至3直至确定摄像机的方向和范围。
注意
在调节镜头位置时，务必使角度调节器上的“BOTTOM ”标记朝向
地板。如果摄像机在“BOTTOM ”标记朝向天花板的状态下被安
装，则显示的图像会颠倒。
安装圆顶罩 
1 将开口罩的开口对着镜头方向。
2 将开口罩按到摄像机上，直至听到喀嗒声。
3 将圆顶罩上的标记与底座上的插槽对齐，并且沿箭头方向转动圆
顶罩，直至听到喀嗒声。然后确保摄像机安装牢固。
典型CCD现象
图像中可能出现的以下现象是CCD（电荷耦合器件）图像传感器所特
有的。这些现象不是故障。
白斑
虽然CCD图像传感器是采用高精度技术生产的，但由于宇宙射线等的
影响，其屏幕上可能会出现细小的白斑（极少数情况）。
这与CCD图像传感器的原理有关，出现的白斑并不是故障。
在以下情况中，⽐较容易出现白斑：
在高温环境下进⾏操作时
提高倍率（灵敏度）时
当使用慢快门时
垂直拖影
拍摄亮度极高的物体（如强聚光灯或闪光灯）时，屏幕上可能出现
垂直尾线，图像也可能出现扭曲。
监视器屏幕 图像上的垂直拖尾显示
高亮物体（如强聚光灯、强反射光、
闪光灯、阳光）
图形失真
拍摄微小的图案、条纹或线条时，它们可能呈锯齿状或出现闪烁现
象。
规格
成像器件 1/3型⾏间转移方式
有效像素 976（水平）× 582（垂直）
焦距长度 2.8 mm - 10.5 mm
最大相对光圈 F1.2
可视角度 SSC-FM531:
水平: 99.5°(广角) - 27.4°
(望远)
垂直: 73.2°(广角) - 20.6°
(望远)
SSC-FM561:
水平: 101.8°(广角) - 27.4°
(望远)
垂直: 73.7°(广角) - 20.6°
(望远)
最小对象距离 0.3 m
信号系统 PAL彩色系统
同步系统 内置/线路锁定可切换
水平分辨率 650线（一般模式）
700线（锐利模式）
最低照度 FM531:
彩色：F1.2时0.10 lx
（50 IRE，AGC ON，Turbo模式）
彩色：F1.2时0.06 lx
（30 IRE，AGC ON，Turbo模式）
黑白：F1.2时0.07 lx
（50 IRE，AGC ON，Turbo模式）
黑白：F1.2时0.05 lx
（30 IRE，AGC ON，Turbo模式）
FM561:
彩色：F1.2时0.10 lx
（50 IRE，AGC ON，Turbo模式）
彩色：F1.2时0.06 lx
（30 IRE，AGC ON，Turbo模式）
黑白：F1.2时0.01 lx
（50 IRE，AGC ON，Turbo模式）
黑白：F1.2时0.006 lx
（30 IRE，AGC ON，Turbo模式）
视频输出 1.0 Vp-p，75 Ω，负同步BNC电缆
视频信噪⽐ 55 dB（AGC OFF，WEIGHT ON）
动态范围 典型的75 dB
电子快门 1/50, 1/120, 1/250, 1/500,
1/1000, 1/2000,1/4000, 1/10000,
1/20000, 1/40000,1/80000,
1/100000（秒）
白平衡 ATW-PRO/ATW/3200K/5600K/MANUAL
⾃动增益控制(AGC) OFF/NORMAL/TURBO/MANUAL
监视器输出 RCA插孔
电源 24V交流 (50 Hz)/12 V直流
功率消耗 2.8 W
操作温度 -10℃至+50℃
存放温度 -40℃至+60℃
操作湿度 20%至80%
存放湿度 20%至95%
尺⼨（直径/高度) ø 121.6 mm × 86.5 mm
质量 SSC-FM531: 约320 g
SSC-FM561: 约330 g
附件 模板（1）
使用手册（本文档）（1）
菜单操作（1）
选购附件 YT-ICB140天花板托架
设计及规格若有更改恕不另⾏通知。
注意
在使用前请始终确认本机运⾏正常。无论保修期内外或基于任何理
由，SONY对任何损坏概不负责。由于本机故障造成的现有损失或预
期利润损失，不作（包括但不限于）退货或赔偿。
定期检查建议
长时间使用本设备时，请定期检查本设备以便安全使用。
虽然设备似乎没有问题，但是长时间使用时其组件质量可能已经下
降，从⽽可能引起故障或事故。
有关详细说明，请咨询购买商店或授权的Sony经销商。
产品中有毒有害物质或元素的名称及含量
使用环境条件：参考使用手册中的操作条件
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
实装基板 × ○ ○ ○ ○ ○
外壳 × ○ ○ ○ ○ ○
光学组件 × ○ ○ ○ ○ ○
附属品 ○ ○ ○ ○ ○ ○
○： 表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T11363-2006标准规定的限量要求以下。
×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超
出SJ/T11363-2006标准规定的限量要求。
For Customer in China
根据中华⼈民共和国信息产业部第39号令《电子信息产品污染控制
管理办法》及标准中要求的“有毒有害物质或元素名称及含量”等
信息，本产品相关信息请参考以下链接:http://pro.sony.com.cn
11