Sony Bravia KLV-S19A10E User manual

- 1 -
WAX
RM-EA002
SERVICE MANUAL WAX CHASSIS
MODEL COMMANDER DEST MODEL COMMANDER DEST
KLV-S19A10U RM-EA002 UK
FLAT PANEL COLOR TV
KLV-S19A10
KLV-S19A10E RM-EA002 AEP
RM-EA002

- 2 -
WAX
RM-EA002
TABLE OF CONTENTS
Section Title Page Section Title Page
Caution ................................................................ 3
Specifications ...................................................... 4
Connectors .......................................................... 5
Self Diagnosis ..................................................... 6
1. GENERAL ................................................................... 7
2. DISASSEMBLY
2-1. Stand Removal .................................................... 16
2-2. Rear Cover Removal ........................................... 16
2-3. VESA Bracket and Bottom Bracket
Assy Removal ..................................................... 17
2-4. A1E Board Removal ........................................... 17
2-5. Shield Cover Removal ........................................ 18
2-6. TU Board Removal ............................................. 18
2-7. BE Board Removal ............................................. 19
2-8. H1E Board Removal ........................................... 19
2-9. H3 Board Removal ............................................. 20
2-10. Speaker Removal ................................................ 20
2-11. Display Cover Removal ...................................... 21
3. SET-UP ADJUSTMENTS
3-1. Signal Adjustment ............................................. 22
3-1-1. Pal auto adjustment (CVBS) ........................... 22
3-1-2. Pal auto adjustment (RGB) .............................. 22
3-1-3. Secam auto adjustment (CVBS) ...................... 22
3-2. White Balance Adjustment ................................. 22
3-2-1. White Balance adjustment (H/L) ..................... 22
3-2-2. White Balance adjustment (C/O) ..................... 23
3-2-3. Secam White Balance adjustment (H/L) .......... 23
3-2-4. Secam White Balance adjustment (C/O) .......... 24
3-3. Test Test Mode .................................................. 24
4. DIAGRAMS
4-1. Block Diagrams(1) ............................................. 25
Block Diagrams(2) ............................................. 26
Block Diagrams(3) ............................................. 27
4-2. Circuit Board Location ........................................ 27
4-3. Schematic Diagrams and Printed Wiring
Boards ................................................................. 27
A1E Board Schematic Diagram .......................... 28
A1E Printed Wiring Board ............................... 34
BE Board Schematic Diagram ............................ 36
BE Printed Wiring Board .................................. 42
TU Board Schematic Diagram ............................ 43
TU Printed Wiring Board ................................. 44
H3 Board Schematic Diagram ............................ 43
H3 Printed Wiring Board .................................. 44
H1E Board Schematic Diagram .......................... 43
H1E Printed Wiring Board ............................... 44
4-4. Semiconductors .................................................. 45
5. EXPLODED VIEWS
5-1. Chassis .............................................................. 47
5-2. Rear Cover and Stand ......................................... 48
6. ELECTRICAL PARTS LIST .................................. 49
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY SHADING AND MARKED ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
WARNING !!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS
DIRECTLY CONNECTED TO THE POWER LINE.

- 3 -
WAX
RM-EA002
The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. F1, H1 etc [ see examples ]. The
servicing of these boards requires special precautions to be taken as
outlined below.
CAUTION
Lead Free Soldered Boards
example 1
example 2
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. Lead Free Solder is
available under the following part numbers :
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires
soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com
rebmuntraP retemaiD skrameR
91-500-046-7mm3.0gK52.0
02-500-046-7mm4.0gK05.0
12-500-046-7mm5.0gK05.0
22-500-046-7mm6.0gK52.0
32-500-046-7mm8.0gK00.1
42-500-046-7mm0.1gK00.1
52-500-046-7mm2.1gK00.1
62-500-046-7mm6.1gK00.1

- 4 -
WAX
RM-EA002
LEDOMMETI metsySnoisiveleT metsySoeretS egarevoClennahC metsySroloC
EL,I,K/D,H/G/B MACIN/NAMREG
oeretS
21E-20E:FHV
96E-12E:FHU
02S-10S:VTAC
14S-12S:REPYH
96R-12R,21R-1R:K/D
96F-12F,Q-B,01F-2F:L
96B-12BFHU:I
MACES,LAP
34.4/85.3CSTN
)YLNOOEDIV(
UI oeretSMACIN96B-12B:FHU
MACES,LAP
34.4/85.3CSTN
)YLNOOEDIV(
eziSerutciPdetcejorP lenaP)yalpsiDlatsyrCduiqiL(DCL
)sehcni91(mc84xorppA
tuptuOdnuoS
rekaepstfeLdnathgiR)SMR(W5x2
]RAER[slanimreTtuptuO/tupnI snoitacificepSlareneG
rotcennocoruEnip-12:1VA
)dradnatsCELENEC(
.slangisoediVdnaoiduArofstupnI
.BGRrofstupnI
.slangisoiduAdnaoediVVTfostuptuO
stnemeriuqeRrewoPV042-022
/noitpmusnoCrewoP
ybdnatS W1/W65xorppA
rotcennocoruEnip-12:2VA
)dradnatsCELENEC(
.slangisoediVdnaoiduArofstupnI
.BGRrofstupnI
slangisoiduAdnaoediVfostuptuO
.ecafretnikniLtramS.)elbatceles(
snoisnemiD )dnatshtiw(mm812x204x864xorppA
)dnatstuohtiw(mm48x463x864xorppA
thgieW )dnatshtiw(gk5.01xorppA
)dnatstuohtiw(gk0.7xorppA
skcaJonohP:3VA
cnysevitagenV3.0,smho57,p-pV1:Y
PBsmho57,p-pV7.0:
PRsmho57,p-pV7.0:
smhoK74,smrVm005:skcaJtupnIoiduA
seirosseccAdeilppuS
)1(rednammoCetomeR200AE-MR
)2(yrettab60RdetangisedCEI
)2(wercSdna)1(tlebtroppuS
rotpadarewopCA
)1(daeLsniaM
busDnip51:5VA
)busDnip51(tupnICP
neerGnocnySnon,smho57,p-pV7.0:G
neerGnocnySnon,smho57,p-pV7.0:B
neerGnocnySnon,smho57,p-pV7.0:R
p-pV5-1:DH
p-pV5-1:DV
serutaeFrehtO
bmoCD3,lenaPDCLelgnAediW
,rosneSthgiL,txeteleT,kniLtramS,retliF
,tupniCP,latigiDEBB,ezeerfPniP
.lautriVybloD
kcajinim:5VAtupnioiduaCP
tuptuooiduA)skcajonohp(thgiR/tfeL
]EDIS[slanimreTtuptuO/tupnI lortnocderarfnI:metsyslortnocetomeR
senohpdaeHkcajinimoerets
stnemeriuqerrewoP
cdV3
noitangisedCEIseirettab2
)AAezis(60R
tupnioiduA:4VA
tupnioediV:4VA
tupnioediVS:4VA
skcajonohp
kcajonohp
NIDinimnip4
.ecitontuohtiwegnahcottcejbuserasnoitacificepsdnangiseD
How to replace the fuse.
Open the fuse compartment with
a screwdriver blade and replace
the fuse.
FUSE
WARNING (UK Models only)
The flexible mains lead is supplied connected to a B.S. 1363 fused
plug having a fuse of 5 AMP rating. Should the fuse need to be
replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one
that carries the ASA
Tmark.
IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUIT-
ABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD
BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG
SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A
PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A
LIVE SOCKET.
When an alternative type of plug is used, it should be fitted with a
5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP
FUSE at the distribution board.
emaNledoM
metI E01A91S-VLK U01A91S-LDK
PniPNONO
TAPFFOFFO
ytiroirPBGRNONO
refooWbuSFFOFFO
1tracSNONO
2tracSNONO
)4(nitnorFNONO
rotcejorPFFOFFO
G/BmroNNOFFO
ImroNNONO
K/DmroNNOFFO
SUAmroNFFOFFO
LmroNNOFFO
TASmroNFFOFFO
MmroNFFOFFO
txeteleTNONO
oeretSmaciNNONO

- 5 -
WAX
RM-EA002
21 pin connector
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
Rear Connection Panels Side Connection Panel
noitarugifnocniptekcosoediVS
niP
oN
langiS leveLlangiS
1dnuorG-
2dnuorG-
3tupni)langisS(Y,mho57Bd3-/+V1
V3.0.cnySevitisop
Bd01+3-
4tupni)langisS(CBd3-/+V3.0
evitisop,mho57
.cnyS
S-Video
socket
_ _ Red input 0.7 +/- 3dB, 75 ohms, positive
_ (S signal Chroma
Connected Not Connected (open) * at 20Hz - 20kHz
Pin No 1 2 Signal Signal level
1Audio output B
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
2
Audio input B
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
3
Audio output A
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
4Ground (audio)
5Ground (blue)
6Audio input A
(left)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
7Blue input 0.7 +/- 3dB, 75 ohms positive
8Function select
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9Ground (green)
10 AVlink
11 Green Green signal : 0.7 +/- 3dB, 75 ohms,
positive
12 Open
13 Ground (red)
14 Ground (blanking)
15
input)
0.3 +/- 3dB, 75 ohms, positive
16 Blanking input
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
17 Ground (video
output)
18 Ground (video
input)
19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
20
Video input 1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
21 Common ground
(plug, shield)
--
--
PC
Input

- 6 -
WAX
RM-EA002
WAX SELF DIAGNOSTIC SOFTWARE
The identification of errors within the WAX chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted).
Flash Timing Example : e.g. error number 3
StBy LED
ON ON
OFF OFF
LED Error Code
DEL
RORRE
EDOC
NOITPIRCSEDRORRE
20rorrEnoitcetorP)AP(ylppuSrewoP
30rorrEnoitcetorP)BP(ylppuSrewoP
40rorrElenaP
50rorrEnoitcetorPtrelACD
60rorrEnoitcetorPrekaepS
70rorrEnaF/PVO/teDCA
80rorrElatigiD
90rorrErenuT
01rorrErossecorPdnuoS
11rorrE)XE-PVS(rossecorPoediV
21rorrE)3612AXC(redoceDamorhC
31rorrE)9602AXC(hctiwSVA
41rorrECICTR
51rorrE)57ML(rosneSerutarepmeT
61rorrE1rednapxEtroP
71rorrE2rednapxEtroP
81rorrE3rednapxEtroP
91rorrEMVN
02rorrECII

– 7 –
WAX
RM-EA002
1
Connect your aerial with the coaxial cable. If connecting to an aerial only (A) Connect your aerial to the socket on the rear of the TV, then go to step 3. If connecting to a VCR with an aerial (B) Connect your aerial to the input socket on your VCR.
2
Connect your VCR. 1
Connect the output socket on your VCR to the
socket on the rear of the TV with the RF lead.
2Connect the scart socket on your VCR to the
/ 2 scart socket on the rear of the TV
with a scart lead.
3
Connect the supplied mains lead to the AC IN socket on the rear of the TV. Note Do not connect the mains lead to your mains socket until all connections are complete.
4
Bundle the cable.
4: Preventing the TV from toppling over After all connections are completed, secure the TV. 1
Fasten the supplied support belt to the stand with a screw.
2
While supporting the TV, tighten the supplied support belt to adjust the length.
3
Fit the supplied support belt to the TV stand, then firmly fasten with the supplied screw using a screw driver or coin, etc.
5: Switching on the TV 1
Connect the TV to your mains socket (220- 240V AC, 50Hz).
2
Press 1on the TV (Top side). When you switch on the TV for the first time, the language menu appears on the screen, then go to “6: Selecting the language and country/region. When the TV is in standby mode (the 1(standby) indicator on the front of the TV is red), press TV +/1on the remote to switch on the TV.
1
3
2
1
2
WEGA
SONY
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
SECTION 1 GENERAL
Getting Started
3: Connecting an aerial/VCR
A
Mains lead (supplied)
3
1
Coaxial cable (not supplied)
Rear of the TV
IN
OUT
(SmartLink)
Y
P
R
/
C
R
P
B
/
C
B
L/G/ S/I
R/D/D/D
R/D/ D/D
L/G/ S/I
PC
Coaxial cable (not supplied)
Scart lead (not supplied)
RF lead (not supplied)
2-
1
Mains lead (supplied)
1
Rear of the TV
3
B
2-
2
VCR

– 8 –
WAX
RM-EA002
Watching TV 1
Press 1on the TV (Top side) to switch on
the TV.
When the TV is in standby mode (the 1(standby) indicator on the front of the TV is red), press TV "/1on the remote to switch on the TV.
2
Press the number buttons or PROG +/- to select a TV channel. To select channel numbers 10 and above using the number buttons, enter the second digit within two seconds.
Additional operations
Watching TV
2
1 2
1
1
WEGA
SONY
To Do this Turn off the TV temporarily (Standby mode)
Press TV "/1.
Turn on the TV from Standby mode without sound.
Press %. Press 2+/- to set the
volume level.
Turn off the TV completely
Press 1 on the top side of the
TV.
Adjust the volume Press 2+ (increase)
/- (decrease).
Mute the sound Return to the previous channel watched (for more than five seconds)
Press %. Press again to restore. Press .
Access the Programme index table
Press OK. To select a channel, press m/M, then press OK.
To access the Input signal index table, see page 16
Press OK. Press
,
to select
the desired input signal, press m/M, then press OK.
Getting Started
6: Auto-tuning the TV After selecting the language and country/region, a message confirming the TV start auto-tuning appears on the screen. You must tune the TV to receive channels (TV broadcasts). Do the following to search and store all available channels.
1
Press OK to select “Yes”. The TV starts searching for all available channels. This may take some time, please be patient and do not press any buttons on the TV or remote. Once all available channels have been stored, the TV returns to normal operation, displaying the channel stored on channel number 1. When a message appears to confirm the aerial connections: No channels are found. Check all the aerial connections and press OK twice to start auto-tuning again.
2
The Programme Sorting menu appears on the screen.
3
To change the order in which the channels are stored on the TV. See page 27.
4
Press MENU to exit. The TV has now tuned in all the available channels.
4 1
Do you want to start
automatic tuning ?
Ye s No
Auto Tuning
Programmes found: 5
Searching...
m

– 9 –
WAX
RM-EA002
Viewing pictures from connected equipment Switch on the connected equipment, then perform one of the following operation. For equipment connected to the scart sockets using a fully-wired 21-pin scart lead Start playback on the connected equipment. The picture from the connected equipment appears on the screen. For an auto-tuned VCR (page 11) Press PROG +/-, or the number buttons, to select the video channel. You can also press / repeatedly until the correct input symbol (see below) appears on the screen. For other connected equipment Press / repeatedly until the correct input symbol (see below) appears on the screen or press OK to
access the Input signal index table. To select an input
source, press m/M, then press OK.
Additional operations
Navigating through menus 1
Press MENU to display the menu.
2
Press M/mto select a menu icon, then
press ,.
3
Press M/mto select an option.
4
Press M/m/</,to change/set the
setting, then press OK.
To exit the menu, press MENU. To return to the last display, press <.
1/ 1, 2/ 2:
Audio/video or RGB input signal through the scart socket / 1 or 2. The symbol appears only if an RGB source has been connected.
3:
Component input signal through the Y, P
B
/C
B
, P
R
/C
R
sockets / 3, and audio input signal through the L/G/S/I, R/D/D/D sockets / 3.
4/ 4:
Video input signal through the video socket 4, and audio input signal through the audio socket L/G/S/I (MONO), R/D/D/D sockets 4. appears only if the equipment is connected to the S video socket 4 instead of the video socket 4, and S video input signal is input through the S video socket 4.
5:
RGB input signal through the PC connectors 5, and audio input signal through the socket .
To Do this Return to the normal TV operation
Press .
Access the Input Signal table
Press OK. To select an input source, press m/M, then press OK.
Using the Menu
1
4
2,3,4
Continued
Picture Adjustment menu
Selects the picture mode. 1Press OK to select “Picture Mode”. 2Press m/Mto select one of the following picture modes, then press OK.
• Vivid: For big lighted spaces. • Standard: Optimal picture for home use. • Custom: Allows you to store your own prefered settings. Tip You can change the picture mode by pressing repeatedly.
1Press OK to select the option. 2Press </,to set the level, then press OK.
Tip “Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes). “Brightness”, “Colour”, “Hue”, “Sharpness” and “Backlight” only appear and can be adjusted if “Picture Mode” is set to “Custom”.
1Press OK to select “Colour Tone”. 2Press m/Mto select one of the following, then press OK.
• Cool: Gives the white colours a blue tint. • Neutral: Gives the white colours a neutral tint. • Warm: Gives the white colours a red tint. Tip “Warm” only appears and can be adjusted if “Picture Mode” is set to “Custom”.
You can select the options listed below on the Picture Adjustment menu. To select options, see “Navigating through menus” (page 16). Tip When you set the “Picture Mode” option to “Vivid” or “Standard,” you can adjust only “Contrast,” and “Reset.”
Picture Mode Contrast/Brightness/Colour/Hue/Sharpness/Backlight Colour Tone
Select: Set: Back:
OK
End:
MENU
Picture Mode Contrast Brightness Colour Hue Sharpness Backlight Colour Tone Reset Noise Reduction
Custom Max 50 50 0 15 5 Warm Auto
Picture Adjustment
Continued

– 10 –
WAX
RM-EA002
Sound Adjustment menu
1Press OK to select “Sound Effect”. 2Press m/Mto select one of the following sound effects, then press OK.
• Natural: Enhances clarity, detail, and sound presence by using “BBE High definition Sound
System
*1
.”
• Dynamic: Intensifies clarity and sound presence for better intelligibility and musical realism by
using the “BBE High definition Sound System.”
• Dolby Virtual
*2
: Uses the TV speakers to simulate the surround effect produced by a multi
channel system.
• Off: Flat response.
Tips • You can change sound effect by pressing 9repeatedly.
• If you set “Auto Volume” to “On”, “Soud Effect” changes to “Natural”.
*1
Licensed by BBE Sound, Inc. under USP4638258, 4482866. “BBE” and BBE symbol are trademarks of BBE Sound, Inc.
*2 Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
Adjusts higher-pitched sounds (Treble), adjusts lower-pitched sounds (Bass), and emphasizes left or right speaker balance (Balance). 1Press OK to select the option. 2Press </,to set the level, then press OK. Resets the “Treble,” “Bass” and “Balance” settings to the factory settings. 1Press OK to select “Reset”. 2Press m/Mto select “OK,” then press OK.
You can select the options listed below on the Sound Adjustment menu. To select options, see “Navigating through menus” (page 16).
Sound Effect Treble/Bass/Balance Reset
Select: Set: Back:
OK
End:
MENU
Sound Effect Treble Bass Balance Reset Dual Sound Auto Volume
Dynamic 0 0 0 A Off
Sound Adjustment
Continued
Screen menu
Automatically changes the screen format according to the broadcast signal. 1Press OK to select “Auto Format”. 2Press m/Mto select “On,” then press OK.
Tips • Even if you have selected “On” or “Off” in “Auto Format”, you can always modify the format of
the screen by pressing repeatedly.
• “Auto Format” is available for PAL and SECAM signals only.
For details about the screen format, see page 15. 1Press OK to select “Screen Format”. 2Press m/Mto select “Wide,” “Smart,” “4:3,” “14:9” or “Zoom” (see
page 16 for details), then press OK.
Adjusts the horizontal picture position so that the picture is in the middle of the screen. 1Press OK to select “RGB Center”. 2Press </,to adjust the centre of the picture between -5 and +5, then
press OK. Tip This option is only available if an RGB source has been connected to the Scarts connectors
1/ 1 or 2/ 2 on the rear of the TV.
You can select the options listed below on the Screen Control menu. To select options, see “Navigating through menus” (page 16).
Auto Format Screen Format RGB Center
Select: Set: Back:
OK
End:
MENU
Auto Format Screen Format RGB Center
On Smart 0
Screen

– 11 –
WAX
RM-EA002
Features menu
1Press OK to select “Power Saving”. 2Press m/Mto select one of the following, then press OK.
• Standard: Default settings. • Reduce: Reduces the power consumption of the TV. • Picture Off: Switches off the picture. You can listen to the sound with the picture off.
Automatically optimizes the picture settings according to the ambient light in the room. 1Press OK to select “Light Sensor”. 2Press m/Mto select “On” then press OK. Sets a signal to be output through the socket labelled / 2 on the rear of the TV. If you connect a VCR to the / 2 socket, you can then record from the equipment connected to other sockets of the TV. 1Press OK to select “AV2 Output”. 2Press m/Mto select one of the following, then press OK.
• TV: Outputs broadcast from the aerial. • AV1: Outputs signals from equipment connected to the / 1 socket. • AV4: Outputs signals from equipment connected to the 4/ 4 socket. • Auto: Outputs whatever is being viewed on the screen.
You can select the options listed below on the Features menu. To select options, see “Navigating through menus” (page 16).
Power Saving Light Sensor AV2 Output
Select: Set: Back:
OK
End:
MENU
Power Saving Light Sensor AV2 Output TV Speakers PC Adjustment
Standard On TV On
Features
Using the Menu
Timer menu
Sets a period of time after which the TV automatically switches itself into the standby mode. 1Press OK to select “Sleep Timer”. 2Press m/Mto select the desired time period (“30min”/“60min”/“90min”/
“120min”), then press OK. The indicator on the TV (front) lights up in amber. Tips • If you switch off the TV and switch it on again, “Sleep Timer” is reset to “Off.” • “Sleep timer will end soon. Power will be turned off.” appears on the screen one minute before
the TV switches to the standby mode.
• If you press / , the remaining time in minutes before the TV switches to the standby mode
is displayed on the screen.
You can select the options listed below on the Timer menu. To select options, see “Navigating through menus” (page 16).
Sleep Timer
Select: Set: Back:
OK
End:
MENU
Sleep Timer Off
Timer
Using the Menu

– 12 –
WAX
RM-EA002
Set Up menu
Starts the “first time operation menu” to tune in all the available channels. Usually you do not need to do this operation because the channels are already tuned when the TV was first installed (page 13). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters). 1Press OK to select “Auto Start Up”. 2Press M/m/</,to select the language, then press OK. 3Press M/mto select the country/region in which you will operate the TV,
then press OK.
4Press OK to select “Yes.”
The auto-tune display appears on the screen.
5Follow steps 1 to 4 of “Auto-tuning the TV” (page 13). Tunes in all the available channels. Usually you do not need to do this operation because the channels are already tuned when the TV was first installed (page 13). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for a new channels that have been launched by broadcasters). 1Press OK to select “Auto Tuning”. 2Follow step 1 and 2 of “Auto-tuning the TV” (page 13).
When all available analogue channels have been tuned, the TV returns to normal operation.
You can select the options listed below on the Set Up menu. To select options, see “Navigating through menus” (page 16).
Auto Start Up Auto Tuning
Select: Set: Back:
OK
End:
MENU
Auto Start Up Auto Tuning Programme Sorting Programme Labels AV Preset Manual Programme Preset
Set Up
Continued
Using Optional Equipment
Connecting optional equipment
Using Optional Equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied. Connecting to the side of the TV To connect Do this S VHS/Hi 8/DVC camcorder AConnect to the S video socket
4 or the video socket 4,
and the audio sockets 4. To avoid picture noise, do not connect the camcorder to the video socket
4 and the S video socket
4 at the same time. If you
connect mono equipment, connect to the L/G/S/I sockets 4, and set “Dual Sound” to “A” (page 21).
Headphones BConnect to the isocket to listen to
sound from the TV on headphones.
Headphones
S VHS/Hi8/DVC camcorder
A
B
To connect Do this Personal Computer C
Connect to the PC Input socket
5 and the audio socket G
on the rear of the TV (page 32).
C
Continued

– 13 –
WAX
RM-EA002
Connecting to the rear of the TV
(SmartLink)
Y
P
R
/
C
R
P
B
/
C
B
L/G/ S/I
R/D/D/D
R/D/ D/D
L/G/ S/I
PC
DVD player with component output
Decoder
DVD recorder / Hard disc recorder
VCR
Decoder
Hi-Fi
PlayStation 2
DVD
F
G
H
E
D
Using Optional Equipment
To connect Do this “PlayStation 2”, DVD player or decoder D
Connect to the scart socket /
1. When you connect the
decoder, the scrambled signal from the TV tuner is output to the decoder, then the unscrambled signal is output from the decoder.
DVD recorder or VCR that supports SmartLink E DVD player with component output F
Connect to the scart socket /
2. SmartLink is a direct link
between the TV and a VCR/DVD recorder. For more information on SmartLink, refer to the instruction manual supplied with your VCR or DVD recorder. Connect to the component socket
3 and the audio sockets 3.
The component signal containing 576p signal format and audio signal are input from the DVD player.
Personal Computer G
See page 31.
Hi-Fi audio equipment H
Connect to the audio output sockets to listen to the sound from the TV on Hi-Fi audio equipment. To turn off the sound of the TV speakers, go to “TV Speakers” on page 24.

– 14 –
WAX
RM-EA002
Specifications Display Unit Power Requirements:
220–240 V AC, 50 Hz
Screen Size:
19 inches
Display Resolution (horizontal x vertical):
1280 dots xlines
Power Consumption:
56 W
Standby Power Consumption:
1 W
Dimensions (w × h × d):
Approx. 468 x 402 x 218 mm (with stand) Approx. 468 x 364 x 84 mm (without stand)
Weight:
Approx. 10,5 kg (with stand) Approx. 7 kg (without stand)
Panel System LCD (Liquid Crystal Display) Panel TV System I. Colour System PAL, SECAM NTSC 3.58, 4.43 (only Video In) Aerial 75 ohm external terminal for VHF/UHF Channel Coverage I: UHF B21–B69 Terminals • AV1: / 1
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, and TV audio/video output.
• AV2: / 2 (SMARTLINK)
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, selectable audio/video output, and SmartLink interface
• AV3: 3
Y:1 Vp-p, 75 ohms, 0.3V negative sync P
B
:0.7 Vp-p, 75 ohms
P
R
:0.7 Vp-p, 75 ohms
3 Audio input (phono jacks)
500 mVrms
Impedance: 47 kilo ohms
• AV4: 4S video input (4-pin mini DIN)
4 Video input (phono jack) 4 Audio input (phono jacks)
• AV5: 5
PC Input (15 Dsub) (see page 35) G: 0.7 Vp-p, 75 ohms, non Sync on Green B: 0.7 Vp-p, 75 ohms, non Sync on Green R: 0.7 Vp-p, 75 ohms, non Sync on Green HD: 1-5 Vp-p VD: 1-5 Vp-p
PC audio input: minijack.
• Audio output (Left/Right) (phono jacks) •i Headphones jack
Sound Output 5 W + 5 W (RMS) Supplied Accessories • Remote RM-EA002 (1) • Size AA batteries (R6 type) (2) • Support belt (1) and screw (2) • AC power adapter (1) •MainsLead(1) Optional Accessories • Wall-Mount Bracket SU-WL11 Note Remove Hinge Cover (cover for bundling the cables) before removing Table Top Stand from the rear of the TV (SU-WL11 Wall Mount Bracket instructions. Page 7, step 4, point 1).
Additional Information
Additional Information
Design and specifications are subject to change without notice. PC Specifications
Signals Horizontal
(Pixel)
Vertical (Line)
Horizontal frequency (kHz)
Vertical frequency (Hz)
Standard
VGA 640 480 31.5KHz 60Hz VGA
640 480 37.9KHz 72Hz VESA 640 480 37.5KHz 75Hz VESA 720 400 31.47KHz 70Hz VGA-T
SVGA 800 600 35.1KHz 56Hz VESA Guidelines
800 600 37.9KHz 60Hz VESA Guidelines
800 600 48.1KHz 72Hz VESA 800 600 46.9KHz 75Hz VESA
XGA 1024 768 48.4KHz 60Hz VESA Guidelines
1024 768 56.5KHz 70Hz VESA 1024 768 60.0KHz 75Hz VESA
WXGA 1280 768 47.40KHz 60Hz VESA
1280 768 47.78KHz 60Hz VESA
This TV does not support Sync on Green or Composite Sync. If a signal other than in the above chart is input, it may not be displayed properly or may not be displayed as you set. Using the Vertical frequency (Hz) of the personal computer at 60 is recommended.

– 15 –
WAX
RM-EA002
Troubleshooting Check whether the 1(standby) indicator is flashing in red. When it is flashing The self-diagnosis function is activated. 1Measure how long the 1(standby) indicator flashes and stops flashing.
For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds.
2Press 1on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or
Sony service centre of how the indicator flashes (duration and interval).
When it is not flashing 1Check the items in the tables below. 2If the problem still persists, have your TV serviced by qualified service personnel.
Picture
Problem Cause/Remedy No picture (screen is dark) and no sound
• Check the aerial connection. • Connect the TV to the mains, and press 1on the TV (top side). • If the 1(standby) indicator lights up in red, press TV "/1.
No picture or no menu information from equipment connected to the scart connector
• Check that the optional equipment is on and press / repeatedly until
the correct input symbol is displayed on the screen.
• Check the connection between the optional equipment and the TV.
Distorted picture • When installing optional equipment, leave some space between the optional
equipment and the TV.
• When changing programmes or selecting Text, turn off any equipment
connected to the scart connector on the rear of the TV.
Double images or ghosting • Check aerial/cable connections.
• Check the aerial location and direction.
Only snow and noise appear on the screen
• Check if the aerial is broken or bent. • Check if the aerial has reached the end of its serviceable life (three to five
years in normal use, one to two years at the seaside).
Picture (dotted lines or stripes) noise
• Keep the TV away from electrical noise sources such as cars, motorcycles,
or hair-dryers.
• Make sure that the aerial is connected using the supplied coaxial cable. • Keep the aerial cable away from other connecting cables. • Do not use a 300-ohm twin lead cable as interference may occur.
Picture noise when viewing a TV channel
• Select “Manual Programme Preset” in the “Set Up” menu and adjust “AFT”
(Automatic Fine Tuning) to obtain better picture reception (page 29).
• Select “Noise Reduction” in the “Picture Adjustment” menu to reduce the
noise in the picture (page 19).
Stripe noise during playback/ recording of a VCR
• Video head interference. Keep your VCR away from the TV. • Leave a space of 30 cm between your VCR and the TV to avoid noise. • Avoid installing your VCR in front of the TV or beside the TV.
Some tiny black points and/or bright points on the screen
• The picture of a display unit is composed of pixels. Tiny black points and/or
bright points (pixels) on the screen do not indicate a malfunction.
Additional Information
No colour on programmes • Select “Reset” in the “Picture Adjustment” menu to return to the factory
settings (page 19).
No colour or irregular colour when viewing a signal from the Y, PB/CB, PR/CR jacks of
3
• Check the connection of the Y, P
B
/C
B
, P
R
/C
R
jacks of 3.
• Make sure that the Y, P
B
/C
B
, P
R
/C
R
jacks of 3 are firmly seated in their
respective sockets.
Sound
Problem Cause/Remedy No sound, but good picture • Press 2+/– or %(Mute).
• Check that “TV Speakers” is set to “on” in the “Features” menu (page 24).
Noisy sound • See the “Picture noise” causes/remedies on page 36.
General
Problem Cause/Remedy The TV turns off automatically (the TV enters standby mode)
• If no signal is received or no operation is performed in the TV mode for 10
minutes, the TV automatically switches to standby mode.
Some input sources cannot be selected
• Select “AV Preset” in the “Set Up” menu and cancel “Skip” of the input
source (page 30).
The remote does not function • Replace the batteries. Wrong characters appear when viewing the menu/Text
• Select “Language” and “Country” in the “Set Up” menu and set the
language and country/region in which Text is provided (page 26). For Cyrillic languages, we recommended that you select Russia if your own country/region does not appear in the list.
Problem Cause/Remedy
Continued
Additional Information

– 16 –
WAX
RM-EA002
SECTION 2 DISASSEMBLY
2-2. REAR COVER REMOVAL
2-1. STAND REMOVAL

– 17 –
WAX
RM-EA002
2-3. VESA BRACKET & BOTTOM BRACKET ASSY REMOVAL
2-4. A1E BOARD REMOVAL
E

– 18 –
WAX
RM-EA002
2-5. SHIELD COVER REMOVAL
2-6. TU BOARD REMOVAL

– 19 –
WAX
RM-EA002
2-7. BE BOARD REMOVAL
2-8. H1E BOARD REMOVAL

– 20 –
WAX
RM-EA002
2-10. SPEAKER REMOVAL
2-9. H3 BOARD REMOVAL