Soundigital LINHA EVOLUTION User manual

SounDigital warrants the original purchaser that this
product shall be free of defects in materials and
workmanship for a period of ninety (90) days from the
original date of purchase. The warranty term is
extended to twelve (12) months if installation is
performed or approved by an authorized SounDigital
dealer (requires proof of installation or approval
required on purchase receipt).
This warranty is not transferrable and applies only to
the original customer from an authorized SounDigital
dealer.
Warranty is void when:
- Defect or problem caused by misuse of the product;
- Incorrect installation or non-conformity with the
Manual;
- Maintenance made by unauthorized personnel;
- Alteration or removal of the seal/serial number;
- Exposure to adverse conditions (weather, humidity,
etc)
- Damage caused by fall or impact;
- Damage caused by natural depreciation;
- Damage caused by transport and/or handling, risks,
or smashings.
- Products was purchased more than 12 months ago.
Warranty covers:
- Component or material with manufacturing defects;
-Workman ship/s ervice ne eded to repa ir the
equipment.
If you need service on your SounDigital amplifier, send
it (freight-prepaid) to SounDigital´s Amplifier Repair
Center through an authorized SounDigital dealer
(must be accompanied by proof of purchase).
- Any extra information you can get by contacting us at
the e-mail address: [email protected];
- In case of manufacturing defect or bad quality of raw
material, the max compensation will be the
replacement of the product, not allowing any kind of
compensation payment;
- New modifications/iterations on a product don't
obligate the manufacturer to modify products formerly
produced.
Limited Warranty
Customer Service Phone - [phone]
General e-mail: [email protected]
Tech Support: [email protected]
Manual SD5000.1D Evolution REV 1.6

Adjust the Low and High pass filters according to your
preference and needs of the speakers. If you have
any doubts, talk to the speakers manufacturer.
After the end of the electrical installation, connect the
negative cable of the battery and, before starting the
audio system, check if all connections are correctly
done.
265A Fuse
To avoid unwanted noise in the system, join the
ground points of the equipment and audio output to
only one point.
In order to adjust the gain, use the headunit volume in
70% of its total, play a musical program of your
preference and turn up the gain until the clip led blinks.
Set the gain in a position where the “CLIP“ LED
doesn't blink.
Some headunits with strong signal output may reach
max power even when the gain is next to its minimum.
In that case, limit the volume of the headunit right
before the point where the clip led starts blinking.
If you need to increase the bass response, adjust the
frequency and gain of the bass boost according to
your preference. Make sure the “CLIP“ LED does not
blink with the new setting.
Gain positioning over the correct
spot may cause noise, trigger
protection state or damage to the
speakers.

Unplug the negative (-) terminal of
the battery before proceeding with
any electrical installation in the
vehicle to avoid fire starts, wounds
or damage to the amplifier.
Never connect or disconnect the
RCA cables with the amplifier on,
be c au s e i t ma y d a m a g e t h e
headunit or the amplifier.
Your Soundigital amplifier needs the correct cables and
electrical system.
The protection fuse/circuit breaker
must be installed at a max distance of
.
30cm (1 foot) from the battery
Be careful when drilling holes in
the vehicle. Verify if you're not
drilling holes in the fuel tank,
brake lines or electrical cables of
the vehicle.
N e v e r u s e s p e a k e r s w i t h
impedance under the nominal
impedance of the amplifier or you
may damage it.
Minimum capacity of the battery
Recommended capacity of the battery
Fuse/circuit breaker size
Size of recommended cable
Use good quality cables (copper if possible) for the
connections to the amplifier.
Installation Tips
The ground cable should be the shortest possible and
should be connected to the chassis of the vehicle.
The surface should be sanded at the contact point to
create a clean, metal-to-metal connection between
the chassis and the termination of the ground wire.
Keep the RCA cables together, but away from the
power or the audio output cables and away from
electric equipment such as electronic fuel injection
centrals, electric engines, etc.
When passing cables through metallic walls, use
rubber grommets to avoid damage to the cable and
short circuits.
Choose a proper place to install the amplifier and
avoid blocking the side ventilation panels.
Securely mount the amplifier so that it does not come
loose in the event of a collision or a sudden jolt to the
vehicle. Avoid mounting it on metallic parts of the
vehicle, because it may cause an earth loop (you
might have noise issues).
Use speakers accordingly to the power and
impedance of the amplifier. Verify if the adjustment
filters can be used to increase the performance of the
equipment.
The Soundigital amplifiers are micro controlled and
have an electronic monitoring of all of their functions,
offering useful information to the user through their
LED’s.
- When constantly on, indicates the amplifier is working.
- When the audio is cut off and it blinks 10 times, it
indicates the current is under 8.9V or over 16v.
- When it blinks during the audio reproduction, it
indicates the input tension is under 9.5 volts.
- When the audio is cut off and the led is constantly on, it
indicates the amplifier is in protection due to high
temperature. Turn the amplifier off until it gets to its
working temperature.
- When the audio is cut off and the LED blinks, it means it
is defective and must be sent to one of our technical
repair centers.
- During the audio reproduction, it makes the sound
distortion monitoring. When it turns on, the speakers
are receiving distorted signal. So, you should turn down
the a mplifier ' s g a in o r th e hea dunit volume.
- When the audio is cut off and it blinks 10 times, it
means a short-circuit or low impedance in the audio
output.
Blue LED
Red LED
Yellow LED
Remove de paint between
the terminal and chassis
0 AWG/50mm²
265Ah
530Ah
265A

10
Weight: 7.8 lb (3.5kg)
Technical Specs
Operating Voltage Input Sensivity
Bass reinforcement frequency
Current Draw (Stand By)
Current Draw (Music)
Max Current Draw
~
-
2A
Power @ 12.6v (double impedance/0.1% max THD+N)
Power @ 12.6v (0.1% max THD+N)
Power @ 14.4v (0.1% max THD+N)
Power @ 14.4v (double impedance/0.1% max THD+N)
0.1%
0.5V ~ 8V
Dimensions:
530 A
265 A
76%
5Hz ~ 80Hz
80Hz ~ 20KHz
5000W
2600W
5600W
2800W
75dB
0.08%
0.08%
10Hz - 15KHz
5Hz - 18KHz
68mm (2.67")
297mm (11.69")
264mm (10.39")
263mm (10.35")
200mm (7.87")
287,5mm (11.31")
264mm (10.39")
223mm (8.77")
LED
LED
LED

9
Peso: 3,5kg (7.8lb)
68mm (2.67")
297mm (11.69")
264mm (10.39")
275,5mm (10.84")
223mm (8.77")
200mm (7.87")
287,5mm (11.31")
263,5mm (10.37")
1. Audio Input RCA connector;
2. Audio Output RCA connector;
3. Variable high pass filter control (5Hz ~80Hz);
4. Variable low pass filter control (80Hz ~20KHz);
5. Variable signal gain control;
6. Variable bass boost control (0dB - +12dB);
7. Variable bass reinforcement frequency control (35Hz ~ 55Hz);
8. Negative audio output connector (-);
9. Positive audio output connector (+);
10. Positive power supply connector (+12v)
11. Remote power supply connector (REM);
12. Negative power supply connector (GND);
13. “Protection” LED indicator;
14. “Clip” LED indicator;
15. “Power on” LED indicator.
W
W
W
W

LED
LED
LED
Capacidade mínima da bateria
Capacidade ideal da bateria

Dear customer
Congratulations on acquiring your Soundigital! You've
just purchased a product of high quality and
technology. The Soundigital products are developed to
assure maximum efficiency and reliability to your sound
system.
Class D Amplifiers:
The main characteristics of Class D amplifiers are:
audio quality, efficiency, versatility and compact
design.
Here are the advantages of these characteristics:
- Audio Quality – Class D amplifiers used to have a
limited response in the past and they used to have a
worse performance regarding higher frequencies than
Class AB amps, despite being more efficient.
Introducing new technologies, Soundigital developed a
Class D amplifier superior to the Class AB ones in
efficiency and performance.
- Efficiency – The Soundigital Class D amplifiers have a
total efficiency (power source + output) higher than
70%, assuring a battery consumption and a heating
lower than the expected.
- Versatility of uses –The flat response of all the
frequencies of Soundigital amplifiers allows them to be
used in all the kinds of systems: SPL, Sound Quality,
Trio Eletrico and Pancadao, meeting the needs with
extreme quality.
- Compact design – The high efficiency and technology
allow our amplifiers to be really compact, making it
easy to install them in vehicles where you have limited
space.
Important info:
Read this manual and follow its instructions and
information carefully. It contains extremely important
information to have your amplifier working properly. If
you feel the need to contact our Tech Support, you can
r e a c h o u r t e ch n i c i an s t h r o u g h t h e e - m a i l
[email protected]
We recommend the use of Soundigital original
accessories for a better performance. The crossovers,
RCA cables and voltmeters offered by Soundigital
follow the same quality standards as our amplifiers,
assuring an excellent quality and high power sound
system to our customers.
To know our complete line of amplifiers and
accessories, visit www.soundigitalusa.com
This “Warning” sign alerts the
user of important info. Not
following this instructions may
cause injuries to the user or
damage to the equipment.
ŸTo prevent injuries to the user or damage to the
amplifier, read all the safety instructions written on
this manual;
ŸIf you have questions about the installation of this
equipment, get in touch with our tech support or with
a professional specialized in car audio installation;
ŸBefore proceeding with the installation of any
electric equipment on your vehicle, unplug the
negative (-) terminal of the battery to avoid fires,
injuries or damages;
ŸUse your sound system safely, exposure to
continuous sound pressure over 85 dB may cause
irreversible hearing loss.
Package contents
· 1 SD5000.1D Evolution Amplifier
· 1 Owner's Manual
· 1 Allen wrench 2.5mm
· 1 Allen wrench 4mm
· 1 Promotional sticker
Contacts:
Customer Service : [phone]
General e-mail:
[email protected]
Tech Support:
[email protected]
Website:
www.soundigitalusa.com
Facebook:
www.facebook.com/comexsoundigital
• Para evitar ruídos indesejáveis ao sistema, una
todos os pontos de aterramento dos equipamen-
tos de audio em um ponto único.
• Após a finalização das conexões elétricas, conecte
o negativo da bateria, e antes de acionar o sistema
de áudio, certifique-se que o ajuste de ganho esta
no mínimo.
• Para ajuste do ganho, posicione o volume da
unidade principal em 70% do volume total,
reproduzindo um programa musical da sua
preferência, aumente gradativamente o ganho até
que o LED “CLIP“ pisque. Retorne até a posição
onde este para de piscar.
• Algumas unidade principais com tensão alta na
saída RCA podem fazer com que a potência máxima
seja atingida mesmo com o ganho posicionado
próximo ao mínimo. Neste caso, limite o volume da
unidade principal antes do ponto onde o LED “CLIP”
começa a piscar.
• Regule os filtros passa alta, passa baixa conforme
seu gosto pessoal e necessidade dos alto falantes
utilizados. Em caso de dúvida, consulte o fabricante
dos alto falantes.
• Caso haja necessidade de incremento nos graves,
regule a freqüência e ganho do “Bass Boost”
conforme seu gosto pessoal. Certifique-se que o LED
“CLIP’’ não será acionado com esta nova regulagem.