Soundoff Signal 100J Series User manual
1
1.800.338.7337 / www.soundosignal.com
ETSSVBK12 1122 REV B
100J/100U SERIES SPEAKER BRACKET (NO DRILL) CAPABLE OF HOLDING UP TO TWO SPEAKERS
FOR DODGE RAM 1500 (5TH GENERATION ONLY) 2019 - 2023, HOOD LATCH MOUNT
ETSSVBK12
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector
manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be sized to
supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
INTRODUCTION:
100J Speaker* Features:
• Designed for clear, powerful output using neodymium
magnet
• Meets CA Title 13, Class A when used with SoundOff
Signal siren amplier
• Composite housing creates electrical isolation from
vehicle chassis to extend product life
• Weather tested, glass reinforced nylon material will not
corrode like a traditional aluminum speaker
• Includes universal bail bracket Design highlights for this
vehicle-specic speaker bracket assembly:
• Holds up to two speakers
• Utilizes universal bail bracket provided with each speaker
CONTAINS
ITEM# COMPONENT QTY
1SPEAKER BRACKET 1
2¼”-20 HEX HEAD BOLT 4
3 ¼”-20 LOCK NUT 4
4¼” FLAT WASHER 4
5INSTALLATION INSTRUCTION SHEET 1
6PRODUCT WARNING CARD 1
7CA PROP 65 LABEL 1
*Speaker and bail bracket sold separately
**Hardware provided to attach up to two speakers
SHOWN WITH 100J SPEAKERS, SOLD SEPARATELY
BRACKET COMPATIBLE WITH
SPEAKERS:
-100J
-100U
2
1.800.338.7337 / www.soundosignal.com
ETSSVBK12 1122 REV B
100J/100U SERIES SPEAKER BRACKET (NO DRILL) CAPABLE OF HOLDING UP TO TWO SPEAKERS
FOR DODGE RAM 1500 (5TH GENERATION ONLY) 2019 - 2023, HOOD LATCH MOUNT
ETSSVBK12
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION:
1. This speaker bracket utilizes the two existing
fasteners for the hood latch mechanism. With
the hood open, remove the shield covering the
area between the radiator and the grille. Next,
remove the front grille and the louvers of the
vehicle in order to access the space in front of the
radiator for speaker bracket installation. Consult
a Stellantis service center for best disassembly
method. Keep all hardware.
2. Attach compatible speakers and bail brackets to
the speaker bracket using the provided ¼-20 hex
bolts and nuts. Tighten to 10 ft-lb. The speaker
bracket can hold a maximum of two speakers. See
FIG.1 for mounting locations.
3. Locate and remove the two fasteners for the hood
latch assembly, as shown in FIG.2.
4. With the hood latch assembly still in its original
position, carefully insert the speaker bracket
assembly into the space in front of the radiator.
Attach the speaker bracket to the vehicle using
the two hood latch assembly fasteners that
were removed in Step 3. Ensure that the existing
wire harness and hood latch release cable are
properly routed in the bracket cutouts. Tighten to
manufacturer’s specications.
5. Adjust each speaker so that the speakers are in-
line with the bail brackets and do not contact the
louvers or radiator. Tighten the fasteners attaching
the speakers to the bail brackets in order to
prevent the speaker from pivoting.
6. Ensure that the speakers are connected to a
power source. Check proper functionality.
7. Reinstall the front grill, louvers, and the shield
according to manufacturer’s specications.
FIG. 2
FIG. 1
This manual suits for next models
2
Table of contents
