Spatz DPSCALE User manual

DPSCALE
Ultra High Resolution Scaler with 3D
O
Op pe er ra at ti io on n M Ma an nu ua al l

DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. SPATZ assumes no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
SPATZ assumes no responsibility for any inaccuracies that may be
contained in this document. SPATZ also makes no commitment to
update or to keep current the information contained in this
document.
SPATZ reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
SPATZ.
© Copyright 2013 by SPATZ. All Rights
Reserved.
Version VR1.0 September 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•Never spill liquid of any kind on or into this product.
•Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•Do not attach the power supply cabling to building surfaces.
•Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY
SUMMARY OF CHANGE
RDV1
06/01/12
Preliminary Release
RDV2
07/02/12
RDV3
31/07/12
Add RS-232 Commands
RDV4
22/12/12
Support timing change

CONTENTS
1. Introduction............................................ 1
2. Applications ........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features .................................................. 1
6. Operation Controls and Functions....... 2
6.1 Front Panel ........................................ 2
6.2 Rear Panel......................................... 4
7.OSD Menu and Function List.................. 5
8. Remote Control...................................... 6
8.1 RS-232 Protocols ............................... 7
8.2 RS-232 Commands........................... 8
9. Connection and Installation............... 10
10. Specifications .................................... 11
10.1 PC, HDMI, DP Input Timing .......... 12
10.2 Output Resolution ........................ 14
11. Acronyms ........................................... 15

1. INTRODUCTION
This high performance video processor which allows 3D movies to be
watched on a 2D display. With HDMI, DisplayPort and PC/Component
inputs to its HDMI output and the associated audio signal processed
synchronously. The operation of both 3D-to-2D and scaling features
can be handled easily through on-panel buttons, IR remote control, or
RS-232 protocol.
2. APPLICATIONS
• Convert 3D signal to 2D signal for 2D display
• 3D source bypass to 3D display without scaling
• Scale HDMI, DisplayPort and PC/Component inputs to HDMI output
3. PACKAGE CONTENTS
• Ultra High Resolution Scaler with 3D
• 5V/2.6A DC power adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
• Input HDMI/DisplayPort/PC sources and output with 2D or 3D HDMI
display.
5. FEATURES
• Supports HDMI 3D processing on Frame Packing and Top-
and-Bottom of 720p@50/60Hz and 1080p@24Hz, Side-by-Side
Half signals of 720p@50/60Hz, 1080i@50/60Hz(input only) and
1080p@24/50/60Hz
• Supports HDMI / Component input timing up to 1080p@50/60Hz,
DisplayPort up to 2560 x 1600@60HzRB and PC up to 1920 x
1200@60/75Hz
• Supports digital and analog audio bidirectional conversion,
extraction and insertion for the audio signals from individual inputs
or from the HDMI source
• Supports component input when connected VGA to 3RCA
adaptor

6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
MENU/
ENTER
OUT
OPTICAL
AUDIO HDMI OUT
POWER
DC 5V
3D OPTICAL AUDIO
BYPASS 3D
→
2D IN
1 MENU/ENTER
Press this button to ENTER the OSD menu. Press again to confirm
the selection.
2 -/IN
a. “-“: When in OSD page, sequentially press this button to move
down the OSD selection.
b. “IN”: Press this button to quick enter the input port selection.
3 +/OUT
a. “+”: When in OSD page, sequentially press this button to move
up the OSD selection.
b. “OUT”: Press this button to quick enter the output resolution
selection.
4 3D BYPASS
Press MENU/ENTER and -/IN buttons simultaneously to switch to 3D
bypass without scaling.
5 3D→2D
Press -/IN and +/OUT buttons simultaneously to switch from 3D to
2D.

6 OPTICAL OUT
This slot is where you connect the amplifier with OPTICAL cable
and from amplifier to speaker.
7 AUDIO L/R OUT
This slot is where you connect the speaker or amplifier with audio
phone jack to the display.
8 OPTICAL IN
This slot is where you connect the input OPTICAL audio source.
9 AUDIO L/R IN
This slot is where you connect the L/R input audio source.
HDMI OUT
This slot is where you connect the HDMI display with HDMI cable.
IR sensor
DC 5V
Plug the 5V DC power supply into the unit and connect the
adaptor to AC wall outlet. Once the system turns on the LED will
turn RED.

6.2 Rear Panel
RS232
HDMI 1 HDMI 2 PC/COMP
SERVICE DisplayPort
IN
1 RS232
This slot is to connect with D-Sub 9pin cable from the PC/NB device
for RS-232 control.
2 SERVICE
This slot is to connect with USB cable for manufacturers’ firmware
update only.
3 DisplayPort IN
This slot is where you connect the DisplayPort source output for
DisplayPort signal sending.
4 HDMI 1/2 IN
These slots are where you connect the HDMI sources output for
HDMI signal sending.
5 PC/COMP IN
This slot is where you connect the PC/NB or DVD/Set-Top Box
source equipment with D-Sub 15-pin cable for PC source signal
input or with D-Sub 15-pin to 3 RCA adaptor for component signal
input.

7.OSD MENU AND FUNCTION LIST
Input Video
PC
COMP
HDMI 1
HDMI 2
DP
Exit
Input Audio
AUDIO
Optical
HDMI/DP
Mute
Exit
Output Resolution
720x480P
1280x720P
1920x1080P
640x480
800x600
1024x768
1280x1024
1600x1200
1920x1200
By Native
3D Bypass
Exit
Output Format
3D→2D
3D Bypass
Exit

Main Menu
2nd Layer
3rd Layer
Misc. Setup
EDID Mode
Internal / External / Exit
Info. OSD Mode
Off / On / Exit
About CS-801H
FW Ver.
Factory Reset
System Reset
Exit
Exit
8. REMOTE CONTROL
1 VIDEO IN
Press to select HDMI 1/HDMI
2/DP/PC/Component input
source.
2 AUDIO IN
Press to select AUDIO/
OPTICAL/HDMI/DP input audio
or MUTE the system.
3 EXIT
Press the EXIT the OSD
selection.
HDMI 1
PC
AUDIO
MUTE
EXIT
INFO
HDMI 2
COMP
OPTICAL
ENTER
DP
VIDEO IN
HDMI/DP
AUDIO IN
MENU
OUTPUT
4 MENU
Press this button to ENTER the
OSD menu.
5 ENTER
Press to confirm the selection.
6 INFO
3D
→ 2D 3D BYPASS NATIVE
CR-111
To show input and output resolution information.
7 OUTPUT
Press to show the output resolution table.
8 ▲/▼
Press up/down buttons to select OSD selection.

9 3D→2D
Press to switch from 3D to 2D.
10 3D Bypass
Press to switch to 3D bypass.
11 Native
Press to switch to Native resolution.
8.1 RS-232 Protocols
RS-232 modem cable.
Pins definition of modem cable
CS-801H
Remote Controller
PIN
Definition
→
←
PIN
Definition
1
NC
1
NC
2
TxD
2
RxD
3
RxD
3
TxD
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 19200 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None

8.2 RS-232 Commands
User Command Code
Description
POWER ?
Power Status
POWER ON
Power On
POWER OFF
Power Off
3D ?
3D Status
3D TO 2D
3D In, 2D Out
3D BYPASS
3D In, 3D Bypass Out
VIDEO ?
Video Input Source
HDMI 1
Video Input in HDMI1
HDMI 2
Video Input in HDMI2
DP
Video Input in DisplayPort
PC
Video Input in PC
COMP
Video Input in Component
AUDIO ?
Audio Input Source
AUDIO
Audio Input in AUDIO
OPTICAL
Audio Input in OPTICAL
HDMI/DP
Audio Input in HDMI/DP
MUTE ON
Mute On
MUTE OFF
Mute Off
INFO ?
Info.OSD Status
INFO ON
Info.OSD On

INFO OFF
Info.OSD Off
OUTPUT ?
Output Status
480P
Output in 480P
720P
Output in 720P
1080P
Output in 1080P
VGA
Output in VGA(640x480)
SVGA
Output in SVGA(800x600)
XGA
Output in XGA(1024x768)
SXGA
Output in SXGA(1280x1024)
UXGA
Output in UXGA(1600x1200)
WUXGA
Output in WUXGA(1920x1200)
NATIVE
Output by Native
EDID ?
EDID Status
EDID INT
EDID By Internal
EDID EXT
EDID By External
FEEDBACK ?
Feedback Status
FEEDBACK ON
RS232 Feedback Enable
FEEDBACK OFF
RS232 Feedback Disable
STATE ?
Video Input Signal Status
VERSION ?
Firmware Version
DEFAULT
Reset to Factory Default
Note: Any commands will not be executed unless followed by a
carriage return. Commands are not case-sensitive.

Amplifier
HD TV PC PC
NB
Optical HDMI
D-Sub15pin VGA
MEN U/
ENTER
OU T
OPTICAL AUDIO HDMI OUT
POWER
DC 5V
RS232
SERVICE DisplayPort
HDMI 1 HDMI 2 VGA
3D OPTICAL AUDIO
BYPASS 3D
→ 2D IN IN
Optical 3.5Ø audio
HDMI
DP
DVD
PC NB
HDMI
Dell PC
Blu-ray

10. SPECIFICATIONS
Video Bandwidth
255MHz/6.75Gbps
DP Input Frequency
Bandwidth
2.7Gbps & 1.62Gbps/Lane
Input Port
2 x HDMI (Female type), 1 x DisplayPort,
1 x VGA
Audio Input Port
1 x L/R, 1xOptical
Output Port
1 x HDMI, 1 x L/R, 1 x Optical
Power Supply
5V DC/ 2.6A (US/EU standards, CE/FCC/
UL certified)
Dimensions (mm)
142(W) x 180(D) x 43(H)
Weight(g)
700
Chassis Material
Aluminum
Silkscreen Color
Black
Operating Temperature
0˚C ~ 40˚C / 32 ˚F ~ 10
Storage Temperature
-20˚C ~ 60˚C / -4 ˚F ~ 1
Relative Humidity
20 ~ 90% RH (non-con
Power Consumption
9W

2D Input Resolution
PC
HDMI
DP
COMP
Input
Resolution
640*350@85
ˇ
ˇ
640*400@85
ˇ
ˇ
720*400@85
ˇ
ˇ
VGA640*480@60/72/
75/85
ˇ
ˇ
ˇ
SVGA800*600@56/60/72/
75/85/120
ˇ
ˇ
ˇ
848*480@60Hz
ˇ
ˇ
XGA1024*768@43i/60/
75/85/120
ˇ
ˇ
XGA+1152*864@75
ˇ
ˇ
1280*720@60
ˇ
ˇ
1280*768@60R/
60/75/85/120R
ˇ
ˇ
ˇ
1280*800@60R/
60/75/85/120R
ˇ
ˇ
1280*960@60/85/120R
ˇ@60/85
ˇ
1280*1024@60/75/85
ˇ
ˇ
ˇ+120R
1360*768@60/120R
ˇ
ˇ
ˇ
1366*768@60
ˇ
ˇ
SXGA+1400*1050@60R/
60/75
ˇ
WXGA+1440*900@60R/
60/75/85
ˇ
ˇ
1440*1050@85/120R
ˇ
ˇ

10.1 PC, HDMI, DP Input Timing
1600*900@60R
ˇ
ˇ
UXGA1600*1200@60/
65/70/75/85/120R
ˇ@60 only
ˇ
ˇ
WSXGA1680*1050@60R/
75/85
ˇ@60CVT/60
ˇ
1792*1366@60/75
ˇ
1856*1392@60
ˇ
1920*1080@60
ˇ
ˇ
1920*1200
(@60R/60/75Hz)
ˇ@60
ˇ
ˇ
1920*1440@60
ˇ
720*480I/P
ˇ
ˇ
ˇ
720*576I/P
ˇ
ˇ
720I/P@50/60
ˇ
ˇ
1080I/P@50/60
ˇ
ˇ
1080P@24
ˇ
2048*1152@60R
ˇ
2560*1600@R
ˇ
3D Input Resolution
HDMI
1080p@24Hz Frame
packing
ˇ
1080p@24Hz Top-and-
Bottom
ˇ
1080p@24Hz Side-by-
Side
ˇ
1080i@50/60Hz Side-by-
Side
ˇ
720p@50/60Hz Side-by-
Side
ˇ

720p@50 / 60Hz Frame
packing
ˇ
720p@50 /60Hz Top-and-
Bottom
ˇ
10.2 Output Resolution
HDMI 3D to 2D and 2D to 2D output Resolution@60Hz
640*480
800*600
1024*768
1280*1024
1600*1200
1920*1200RB
480P
720P
1080P
HDMI 3D to 3D Bypass Output Resolution
Frame Packing: 720p@50/60Hz, 1080i@60Hz, 1080p@24/30Hz
Top-and-Bottom: 720p@50/60Hz, 1080i@60Hz, 1080p@24/30Hz
Side-by-Side: 720p@50/60Hz, 1080i@60Hz, 1080p@24Hz
Note: Some output display may not support 3D@50Hz and therefore,
some 3D 50Hz signal may not be display.

11. ACRONYMS
ACRONYM
COMPLETE TERM
HDMI
High-Definition Multimedia Interface