SpinCore Technologies PA10W User manual
RF Power Amplifier PA10W
Congratulations and thank you for choosing a design from
SpinCore Technologies, nc.
We appreciate your business!
At SpinCore we try to fully support the needs of our customers. f you
are in need of assistance, please contact us and we will strive to provide
the necessary support.
© 2011 SpinCore Technologies, Inc. All rights reserved.
SpinCore Technologies, Inc. reserves the right to make changes to the product(s or information herein without notice. RadioProcessor™,
PulseBlaster™, SpinCore, and the SpinCore Technologies, Inc. logos are trademarks of SpinCore Technologies, Inc. All other trademarks
are the property of their respective owners.
SpinCore Technologies, Inc. makes every effort to verify the correct operation of the equipment. This equipment version is not intended
for use in a system in which the failure of a SpinCore device will threaten the safety of equipment or person(s .
http://www.spincore.com 2 2014-02-20
RF Power Amplifier PA10W
Table of Contents
. Precautions ................................................................................................... 4
Connecting & Disconnecting Power Amplifiers.........................................................4
Power Considerations................................................................................................4
. PA10W – 10 W Power Amplifier Module ................................................... 5
1. Overview ...................................................................................................................... 5
2. Electrical Specifications ............................................................................................ 5
3. PA10W RF Module with Deblanking Circuitry ......................................................... 6
RF Input and Output Connectors...............................................................................6
TT Control Input Connector.....................................................................................7
DC Power Input Connector ......................................................................................8
4. PA10W RF Module Enclosure Options ..................................................................... 9
1) PA10W module in a single bay enclosure (Figure 6)............................................9
2) PA10W module enclosed with iSpin-NMRTM system (Figure 7)........................10
3) PA10W module in ightweight aluminum enclosure (Figure 8)..........................10
4) PA10W RF in enclosure with Preamplifier Option...............................................11
. Related Products and Accessories ........................................................ 12
V. Contact nformation ................................................................................. 12
V. Document nformation .............................................................................. 12
http://www.spincore.com 3 2014-02-20
RF Power Amplifier PA10W
. Precautions
Working with RF power amplifiers can be dangerous and even fatal if not handled properly.
Output voltages can reach values greater than 90 V peak-to-peak and can be fatal. Follow these
steps to avoid damaging the amplifier or inflicting serious injuries.
Connecting & Disconnecting Power Amplifiers
When connecting the power amplifier, follow these steps to avoid damaging the amplifier or
inflicting serious injuries.
1 Apply the load to the amplifier (make sure a load is ALWAYS present when working with
power amplifiers .
2 Apply the DC power to the amplifier.
3 Apply the RF input to the amplifier.
Repeat the steps in reverse order when disconnecting the amplifier.
Power Considerations
Make sure the following considerations have been made before applying power to the amplifier.
1 Be sure your load can appropriately dissipate the maximum power being applied by the
amplifier.
2 When applying an RF signal, work with low duty cycles to limit the power being
dissipated. The duty cycle ratio should be below 1% for safe operation.
http://www.spincore.com 4 2014-02-20
RF Power Amplifier PA10W
. PA10W – 10 W Power Amplifier Module
1. Overview
The PA10W RF power amplifier comes in a very compact broadband module delivering 10 Watts
RMS (20 Watts PEP, Peak Envelope Power into a 50-ohm load. It has a 3 dB range of 10 MHz to
75 MHz and is powered by a DC +12 V power supply (with the negative terminal grounded . The
PA10W has standard female SMA jacks for RF input and output, and a standard 4-pin ATX
connector for the input DC power. The PA10W typically operates in Class AB. The rise and fall
time for the RF pulse output is typically around 200 ns.
The product comes with blanking circuitry – the blanking circuitry keeps the PA10W blanked
(turned off until a TTL input (logical high is applied to deblank it. The blanking circuitry helps to
conserve power, keeps the amplifier cool under typical operating conditions, and provides noise
reduction during the reception of NMR signals.
The PA10W module measures 2.25" x 1.4" x 1.4" (57 x 36 x 36 mm . There are multiple
ordering options available, such as enclosures with integrated AC power supplies and enclosures
with a complete RF front-end with preamplifiers and filters for a complete mobile NMR, NQR and
MRI system. See the “Configuration Options” section later in this document for more information.
The use of a low pass (or band pass filter at the output of the PA10W is recommended to reduce
high frequency noise and improve performance.
2. Electrical Specifications
Parameter
Specification
Units
Max DC Input Voltage
12
V (DC
Max RF input power
50
mW
Max. continuous RF output power
10
W (RMS
TTL Deblaking Voltage
3.3
V
http://www.spincore.com 5 2014-02-20
RF Power Amplifier PA10W
Table 1: Basic electrical specifications for the PA10W power amplifier module.
3. PA10W RF Module with Deblanking Circuitry
This configuration shown in Figure 1 does not have an enclosure and includes the switching
circuitry mounted on top of the power amplifier to enable it when a TTL pulse is applied to the input
pin. This feature reduces power consumption and keeps the power amplifier cool.
Figure 1: PA10W RF power amplifier module
RF Input and Output Connectors
A top view of the PA10W module depicting RF input and output connectors is shown on the next
page in Figure 2. When connecting the PA10W power amplifier, the RF signal source should be
connected to the SMA jack on the right hand side (top view of the circuit (RF in . The SMA jack on
the left hand side (top view is the RF output from the power amplifier (RF out .
http://www.spincore.com 6 2014-02-20
RF Power Amplifier PA10W
Figure 2: Diagram of power amplifier RF connectors (top view . RF out and RF in are SMA
jack connectors.
TT Control Input Connector
The PA10W power amplifier module has a 10-pin shrouded male IDC connector1, also shown in
Figure 2 above, which supplies the input TTL control signal. The control signal is pin 8 on the IDC
header and the corresponding ground is pin 7. The input is terminated by a 100-ohm load and
requires an external TTL signal source capable of outputting at least 10 mA. The TTL requirements
for the deblanking control input are standard low voltage TTL values of 3.3V for a logical high, 0V
for a logical low. A logical high signal is required to deblank (enable the PA10W. The deblanking
bit must be set at least 3 ms prior to sending the RF signal or optimal power will not be achieved.
Figure 3: 10-pin IDC connector (Digi-Key part A33159-ND . Mates with Digi-Key part
HKC10H-ND or similar.
1 Note: The deblanking TTL input header is denoted P2 on the circuit board. Please see Figure 3 above, for pin diagram.
http://www.spincore.com 7 2014-02-20
RF Out
RF Power Amplifier PA10W
The timing diagram of a typical application of PA10W with the deblanking pulse applied prior to the
RF pulse is presented in Figure 4 below. When working with short RF pulses, on the order of 1 us
or so, triggering the oscilloscope on the falling edge of the deblanking pulse will help with identifying
and capturing the RF pulse on the scope.
Figure 4: Representation of the deblanking and RF input and output signals to the PA10W. The
PA10W requires at least 3.0 ms of deblanking time prior to the RF pulse for full output power.
DC Power Input Connector
The PA10W RF power amplifier has a 4-pin input power connector. The input is for use with a
standard PC ATX power supply connector. The pin arrangements for this connector are shown on
the next page in Figure 5.
http://www.spincore.com 8 2014-02-20
Deblanking
Signal
RF Output
Deblanking Delay Pulse Time
RF Input
RF Power Amplifier PA10W
Figure 5: 4-Pin input connector (Molex part 05310 0410). Mates with standard
PC power supply connector or Molex part 0015244048.
4. PA10W RF Module Enclosure Options
The PA10W RF power amplifier module can be delivered in various external enclosures which
protect the RF power amplifier circuitry and include an AC/DC power supply, internal RF cables and
output low-pass (or band-pass filter (please specify your operating frequency at the time of
purchase . The power input is 90-264 V AC, the RF input/output signals are provided on external
BNC connectors, and the TTL inputs are routed through female DB-9 input connectors. The active
TTL signal needs to be connected to pin 4, with the corresponding ground line connected to pin 8.
Three standard enclosure configurations are available:
1) PA10W module in a single bay enclosure (Figure 6)
Single bay enclosure additional specifications include:
-Excellent EMI/RFI shielding which meets FCC & CE regulations.
-Built-in 4x4 cm quiet cooling fan.
-High quality 50 Watt AC input switching power supply.
-Dimensions are approximately 10.25” x 7.75” x 2.25” (26 x 19.5 x 6 cm .
http://www.spincore.com 2014-02-20
RF Power Amplifier PA10W
Figure 6: PA10W RF power amplifier – single bay enclosure.
2) PA10W module enclosed with iSpin-NMRTM system (Figure 7)
iSpin-NMR enclosure additional specifications include:
-Metal body with streamlined plastic front panel.
-Built-in 8x8 cm quiet cooling fan.
-High quality 80 Watt AC input switching power supply.
-Dimensions are approximately 11” x 7” x 6.75” (28 x 18 x 17 cm .
Figure 7: PA10W RF power amplifier – enclosed with iSpin system.
3) PA10W module in ightweight aluminum enclosure (Figure 8)
Small aluminum enclosure additional specifications include:
-Lightweight aluminum enclosure.
-High quality external 60 Watt AC input switching power supply.
-Dimensions are approximately 4” x 2.4” x 3” (10 x 6 x 8 cm .
http://www.spincore.com 10 2014-02-20
RF Power Amplifier PA10W
Figure 8: PA10W RF power amplifier – lightweight aluminum enclosure.
4) PA10W RF in enclosure with Preamplifier Option
The enclosure can also include input preamplifiers (approx 45 or 60 dB of gain – please specify
when ordering to the RadioProcessor board. This option is perfect in combination with the iSpin-
Mini system to provide a complete mobile NMR system (see Figure 9 .
Figure 9: Block diagram of RF front-end for the RadioProcessor; typical applications include
NMR, NQR, and MRI experiments.
http://www.spincore.com 11 2014-02-20
TTL (de-blanking) from RadioProcessor
RF Power Amplifier PA10W
. Related Products and Accessories
1. Alternate power levels available: 15 W, 75 W and 100 W. For more information, please visit
the URL http://www.spincore.com/products/RFPA/
2. iSpin-NMR, The Complete, Simple, Intuitive, Effective and Portable NMR System. For more
information, please visit http://spincore.com/products/iSpinNMR/
3. Complete single-card solution for RF pulse generation and acquisition, the RadioProcessor.
For more information, please visit http://www.spincore.com/products/RadioProcessor/
4. NMR Permanent Magnets are available for conducting NMR experiments. For more
information, please visit http://www.spincore.com/products/Magnets/
5. If you require a custom power level, please inquire with SpinCore Technologies through our
contact form, which is available at http://www.spincore.com/contact.shtml
V. Contact nformation
SpinCore Technologies, nc.
4631 NW 53rd Avenue, SU TE 103
Gainesville, FL 32653
USA
Telephone (USA): 352-271-7383
Fax (USA): 352-371-8679
Website: http://www.spincore.com
Web Contact Form: http://www.spincore.com/contact.shtml
V. Document nformation
Revision history available at SpinCore.
http://www.spincore.com 12 2014-02-20
Other manuals for PA10W
1
Table of contents
Other SpinCore Technologies Amplifier manuals
