SportsPlay 902-706 Instruction manual

Early Years Bench With Back
For Part Numbers:
902
-
706 &
902-707
Component Details
Item No.
Part Number
Description
QTY
1
*Style Index
Bench Plank
2
2
*Frame I
ndex
Bench
Leg
2
3
126
-
704
3/8 x 3” Button Head Bolt
8
4
316
-
601
3/8 Washer
8
5
416
-
505
7/32 Allen
1
6
516
-
400
LocTite
1
Additional Components for Surface Mount
11**
531
-
352
3/8 Concrete Anchor
8
Version: EY Bench08.v2
www.sportsplayinc.com
1
3
4
1
2
Detail B
4
2
3
1
Detail A
**Only Required on Surface on units that have a surface mount
frame
Note: Refer to the frame index and style index for part identification and
component specific instructions.

Early Years Bench With Back
For Part Numbers:
902
-
706 &
902-707
Important
Please keep a copy of these instructions in your files. There is
important replacement part information in them that will assist
you in the event a part is ever needed.
Assembly Information
Read all assembly instruction before starting assembly.
Verify that all parts were received by comparing the parts
received to the component list on page one.
If your product mounts to something (surface mount, in ground
or wall mount) you will assemble the entire product before
drilling holes or mounting frame in order to ensure proper
layout.
CONTACT YOUR DISTRIBUTOR ABOUT ANY PARTS YOU ARE
MISSING. You must report missing parts within 10 days of
delivery.
Hand-tighten all bolts during the initial assembly (unless
specifically told to tighten completely in the instructions). Once
the unit is fully assembled and square you should completely
tighten them.
Other than when a specific step in the assembly instructions
specifies “to not apply LocTite, we recommend applying a small
amount to all assembly bolts.
General Maintenance
It is recommended that you inspect the product monthly for
loose bolts and broken parts. If replacement parts are needed
please refer to these instructions for part numbers and
descriptions then call your distributor to order replacements.
Assembly Instructions
NOTE: Only assembly your bench at this time. After it is assembled
you may refer to the frame index so you can identify your frame type
and then locate the specific mounting instructions for that frame.
1. Attach one of the Bench Planks (1) to one of the Bench Legs (2)
by inserting two 3/8” x 3” Button Head Bolts (3) and 3/8” Washers
(4) through the bottom of the leg and into the factory installed
nuts on the mounting plate attached to the bottom of the bench
plank (Detail B)
2. Following the same procedure established in step 1, attach the
same Bench Plank (1) to the second Bench Leg (2) using two 3/8” x
3” Button Head Bolts (3) and 3/8” Washers (4).
3. Attach the second Bench Plank (1) to the Bench Legs (2)
following the procedures outlined in steps 1 and 2. Use detail A
from the first page as a reference.
4. Now identify your frame type from and follow the specific
instructions for your frame. Again, use the frame index page to
complete this step.
V
ersion: EY Bench
08.v2
www.sportsplayinc.com
2

Early Childhood Bench Frame Style
Index and Install
STD Bench EC Frame Index_08.v1
www.sportsplayinc.com
Frame Index
613
-
803
I
In ground
With Back
613
-
803P
Portable
With Back
613
-
803
S
Surface
With Back
In Ground Mount Instructions:
1) IN GROUND MOUNT (Refer to the Footing Diagram
below) – Dig two holes 12” in diameter, 20” deep and
span the distance of the legs from center to center.
2) Place the bench into the holes and level (also make
sure bench is still square). Completely fill the holes with
concrete. After you add the concrete, make sure that it
didn’t cause the bench to shift out of level.
3) We recommend that the top of the concrete slope
down and away from the Bench leg to help with water
runoff.
20”
12”
In Ground Footing
Diagram
Portable Frame Instructions:
1) Attach the bench planks () to the frame by
inserting a 3/8 x 3” Button Head bolts () and 3/8
washer () through the bottom of the leg and into the
factory installed nut on the bottom of the bench
plank. Detail B. Repeat process on remaining holes
in the frames and bench planks.
2) Finally, tighten all remaining bolts.
Surface Mount Instructions:
1) After bolts have been tightened, place the bench in the desired
permanent location and mark the holes from the mounting plate
onto the mounting surface. Move the bench
and drill the marked holes 3.75” deep with a 3/8” bit.
2) Remove the nuts and washers from the anchor
bolts (11) and place the anchor bolt into the drilled
holes. Back the bolt in the anchor out far enough so
there are sufficient threads exposed for the nut after
the bolt goes through the mounting plate and washer.
3) Put the bench back in place. Put the put a washer and
hand tightened nut on each anchor, do not completely
tighten until all nuts are hand tight. Square and level the bench
and then tighten all other bolts.

Early Childhood Bench
Style Options
www.sportsplayinc.com
Style
Index
Style Identification
In the event a replacement part is needed, it is important that you are
able to identify not only the product but the style of product you
ordered. The images to the right represent all the style options that are
available for the product you purchased. Please identify your style and
its corresponding part number before you contact your distributor or the
manufacturer for replacement parts.
Currently, SportsPlay Equipment offers four style options. Rolled edge
with perforated steel, beveled edge with perforated steel, rolled edge
with expanded steel and beveled edge with expanded steel.
To identify your product style you must first define the edge. If it has a
radius it is a rolled edge and if it has a 45 degree angle it is the beveled
edge. Expanded steel is easily identified by its distinct weave pattern.
The perforated steel option is simply sheet metal that has been punched
with a pattern of holes.
613-802P N/A
613-802E N/A
Rolled/Perforated Beveled/Perforated
Rolled/Expanded Beveled/Expanded