ST-Lab U-1430 User manual

PCIe USB 3.1 Gen2 Host Adapter
User Manual
Ver. 1.00
All brand names and trademarks are properties of their
respective owners.

Contents:
Chapter 1: Introduction ......................................................3
1.1Features.........................................................................3
1.3 System Requirements ..................................................3
1.4 Package Contents.........................................................4
Chapter 2: Getting Started .................................................4
2.1 Hardware Installation ..................................................4
2.2 Driver Installation........................................................5
2.3 Hardware Verify...........................................................7
2.4 Driver Uninstall ...........................................................8
MN2000000230 Page 2

Chapter 1: Introduction
1.1Features
Compliant with PCI Express Base 3.0 Specification
Support PCI Express Gen2 x2 or Gen3 x1
Compliant with Universal Serial Bus 3.1 Specification Revision
1.0
Compliant with Universal Serial Bus Specification Revision 2.0
Backward to compatible with USB 3.0/2.0/1.1 interface
Up to 10 Gbps bandwidth performance with low latency
Support two Type-C port of USB 3.1
Compliant with eXtensible Host Controller Interface (xHCI)
Specification Revision 1.1
Built-in over current protection on each USB port
1.3 System Requirements
Windows® 7/8/8.1/10 (32/64 bit)
One available PCI Express slot (x4, x8, or x16)
MN2000000230 Page 3

1.4 Package Contents
1 x PCIe USB 3.1 Gen2 Host Adapter
1 x User Manual
1 x Driver CD
1 x Low Profile Bracket
Chapter 2: Getting Started
2.1 Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCI Express slot (x4,
x8, or x16).
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
fir mly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Secure the computer cover and reconnect the power cord.
MN2000000230 Page 4

2.2 Driver Installation
1. Insert the provided CD into your disk drive. The CD-ROM will
start automatically. The following screen will show up and please
click “Install Driver”.
*Note: Actual image may vary
Note: If the install program doesn’t run automatically, please
locate and double-click on the Autorun.exe file in the CD to
launch the install program.
2. Please click “ASM1142” to start the installation.
MN2000000230 Page 5

*Note: Actual image may vary
3. Click “Next” to continue.
Please check accept license agreement box, and click “Next” to
continue.
4. Click “Finish” to end of the driver installation steps.
MN2000000230 Page 6

Note: The PCIe USB 3.1 Gen2 Host Adapter’s driver was
embedded into Windows 8/8.1/10 OS. That’s, the driver can be
installed into Windows 8/8.1/10 automatically.
2.3 Hardware Verify
1. Click on the “Device Manager”tab in the Windows Control
Panel.
Start > Control Panel > Device Manager
MN2000000230 Page 7

2. Entry “Universal Serial Bus controllers” item, and you can read
“ASMedia XHCI 1.1 Controller” and “USB Root Hub” in the
Device Manager.
2.4 Driver Uninstall
1. Click on the “Programs and Features”tab in the Windows
Control Panel.
MN2000000230 Page 8

Start > Control Panel > Programs and Features
2. Entry “Uninstall or change a program” page, and double click
“Asmedia USB 3.0 Host Controller Driver” to process driver
uninstallation procedure.
MN2000000230 Page 9