Steel Core 42797 User manual

*Actual product may vary slightly
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property
damage and/or personal injury. Please keep instructions for future reference.
For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
For Customer Service, Call 1-800-348-5004
or e-mail [email protected] 42797 01/2017
PARTS RACK WITH 24 REMOVABLE BINS
42797

[email protected] 21-800-348-5004
SPECIFICATIONS
ASSEMBLY PRECAUTIONS
IMPORTANT SAFETY INFORMATION
1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the influence of drugs or medication.
6. Weight capacity and other product capabilities apply to properly and completely
assembled product only.
7. Place on stable, sturdy bench capable of supporting product’s fully loaded weight.
Do not place near the bench’s edge.
USE PRECAUTIONS
1. This product is not a toy. Do not allow children to play with or near this item.
2. Use as intended only.
3. Inspect before every use; do not use if parts are loose or damaged.
4. Maintain product labels and nameplates. These carry important safety information.
If unreadable or missing, contact FOT Tools for a replacement.
1. Using two bolts from the side and one bolt from the back, attach the Left Panel (1) to
the Top (3) with the lip facing inside.
2. Repeat step 1 to attach the Right Panel (2) to the Top (3).
3. Attach a Back Brace (7) to the lowest hole on the back of each Panel (1,2).
4. Cross the Back Braces (7) and attach to the upper holes on the opposing Panels.
5. Place a Bracket (4) on each end of a Shelf (5). Align the Shelf and Brackets in place
between the Panels, and secure two bolts each end.
6. Repeat step 5 for the other two Shelves.
7. Make sure the assembly rests level, then wrench tighten all Nuts and Bolts (8).
8. Place the Bins (6) onto the Shelves.
ASSEMBLY INSTRUCTIONS
Note: All parts are secured using Bolts, Nuts, and Washers (8), with the Bolts inserted
from outside the rack. Only finger tighten Bolts and Nuts (8) until assembly is complete.
Weight Capacity Per shelf 44 lb.
Total 132 lb.

PARTS LIST AND DIAGRAM
Part Description Qty
1 Left Panel 1
2 Right Panel 1
3 Top 1
4 Bracket 6
5 Shelf 3
6 Bin 24
7 Back Brace 2
8 M6 x 12 Bolt-Nut-Washer Set 22
3
2
1
7
8
View from rear
1
3
2456
View from front
[email protected] 31-800-348-5004

Limited Manufacturer Warranty
FOT makes every effort to ensure that this product meets high quality and durability
standards. FOT warrants to the original retail consumer a 1-year limited warranty
from the date the product was purchased at retail and each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of
maintenance. FOT shall in no event be liable for death, injuries to persons or
property, or for incidental, special or consequential damages arising from the
use of our products. To receive service under warranty, the original manufacturer
part must be returned for examination by an authorized service center. Shipping
and handling charges may apply. If a defect is found, FOT will either repair or
replace the product at its discretion.
DO NOT RETURN TO STORE
For Customer Service:
Email: [email protected] or Call 1-800-348-5004
[email protected] 41-800-348-5004