Belnick GC-MBLK64-GY-GG User manual

Customer Service Email: [email protected] | Phone:[phone]
GC-MBLK64-GY-GG/GC-MBLK64-WH-GG/GC-MBLK64-BR-GG
Assembly Time
Thank you for your purchase!
Classic Four Pane Glass Door 65" TV Stand
for up to 80" TVs
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/GC-MBLK64-BR-GG.pdf
ASSEMBLYINSTRUCTIONS
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during
assembly.
Tighten all components securely before use. Failure to do so may result in personal injury.DO NOT use any sharp
objects to open plastic wrapped components as damage to product or components may result.
Load Bearing
60 min
LBS LBS LBS 200 LBS
LBS 30 LBS
LBS LBS LBS
LBS

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone
of long-lasting consumer relationships. We strive toward excellence
in all we do and want you to be completely satisfied with your
purchase. Please contact our exceptional Customer Experience
Agents at the email address or phone number shown below to assist
you with any product questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to
resolve any issues you may have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal
usage, according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters are warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for
the product. In the absence of product-specific restrictions and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by parties
other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of
leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage
attributable to use by persons exceeding specified weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resulting from use of this product. Liability for
incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

PARTS
1（1）
28+1
1（11）1
E
1
1（2）
36+1
3.5*14
F
1（12）
2（3）
8+1G
1（13）
1（4）
2H
1（14）
1（5）
2I
2（15）
1（6）
2J
2（7）
12K16+1A
1（8）
4L20+1B
1（9）
2M8+1C
2（10）
28+1D
Dowel Peg
Door Knob
Door Strike Plates
Bottom Plate
Top Plate
Long Screw-In Peg
Short Screw-In Peg Bottom Support Feet
Door Hinges
Shelf Holders
Left Side Panel
Right Side Panel
Left Side Panel Front Fascia
Left Side Panel Back Fascia
Right Side Panel Front Fascia
Right Side Panel Back Fascia
Note: Ensure slot opening is
facing up
Note: Ensure slot opening is
facing up
Cam Lock Connector
Lower Back Panel
Upper Back Panel
Inner Supports
Inner Supports Fascia
Front Doors
Cam Lock Connector Covers
Left & Right Upper Shelves
Middle Shelf
Back Panel Screws
Door Knob Screws
Screws

STEP 1
STEP 2
（11）
（13） （14）
（12）
A*16
B*20
C*8
（1）
（2）
（6）
（5）
（6）
（5）
（10）
*2
（7） *2
（11）
（12）
（13）
（14）
A
A
A
A
A
A
AA
A
A
A
A
BB
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
JJ
J
J *2
F *4
F *2
F *2
D
D
D
D
D
D
D
D
D*8
Insert Long Screw-In Pegs (Part
B) and turn clockwise with
Phillips screwdriver to tighten
Insert Dowel Pegs
Top Plate
Door Strike Plate
Door Strike Plate
Note: Ensure Groove on Underside of Top Plate Faces the Rear
Note: Ensure Groove on Underside of Bottom Plate Faces the Rear
Inner Supports Fascia (Part 7)
Door
Strike
Plates
Bottom Plate
Left Side
Panel
Right Side
Panel
Left Rear Fascia Right Rear Fascia
Left Front Fascia
Right Front Fascia
Note: Ensure Groove
Openings Face Up
Insert Short Screw-In
Pegs (Part C) and turn
clockwise with Phillips
screwdriver to tighten
Inner Supports
Cam
Lock
Fully insert Cam Lock
(Part D) into hole and turn
clockwise with common
screwdriver to tighten
once screw-in peg is
inserted.
Note: Arrow should be
pointing outwards
Left Side Panel
Cam Lock
Left Side Rear Facia
Groove Opening (Ensure Facing Up)
STEP 2A: Ensure Cam Locks (Part D) are
inserted in holes with open side facing outwards
toward receiver hole for Screw-In pegs (Arrow
Side). Insert Short Screw-In Pegs on the Left
Side Rear Fascia (Part 13) into the Cam Locks
(Part D) on the Left Side Panel. Turn Cam
Locks clockwise to tighten.
Open Side
Closed
Side
STEP 2B: Ensure Cam Locks (Part D) are
inserted in holes with open side facing outwords
toward receiver hole for Screw-In pegs (Arrow
Side). Insert Short Screw-In Pegs on the Left
Side Front Fascia (Part 11) into the Cam Locks
(Part D) on the Left Side Panel. Turn Cam
Locks clockwise to tighten.
Left Side Front Fascia
STEP 2C: Ensure Cam Locks (Part D) are
inserted in holes with open side facing outwords
toward receiver hole for Screw-In pegs (Arrow
Side). Insert Short Screw-In Pegs on the Right
Side Rear Fascia (Part 13) into the Cam Locks
(Part D) on the Right Side Panel. Turn Cam
Locks clockwise to tighten.
Right Side Rear Fascia
Right Side Panel
Groove Opening (Ensure Facing Up)
Cam Lock
Right Side Front Fascia
STEP 2D: Ensure Cam Locks (Part D) are
inserted in holes with open side facing outwards
toward receiver hole for Screw-In pegs (Arrow
Side). Insert Short Screw-In Pegs on the Right
Side Front Fascia (Part 12) into the Cam Locks
(Part D) on the Right Side Panel. Turn Cam
Locks clockwise to tighten.
Top of right side Panel
Top of left side Panel
Screw-In Peg
Receiver
Hole

STEP 3
STEP 4
D*4
（2）
（5）
（6）
D
D
D
D
F *8
M *2
M
M
F
*4
F *4
Cam Lock
STEP 3: Ensure Cam Locks (Part D) are inserted in holes
with open side facing outwords toward receiver hole for Screw-
In pegs (Arrow Side). Insert Long Screw-In Pegs (Part B) at the
bottoms of the Left Side Panel (Part 5) and Right Side Panel
(Part 6) into the Bottom Plate (Part 2) and Turn Cam Locks
clockwise to tighten. Ensure Dowel Pegs (Part A) are fully
seated when tightened.
Note: Ensure Groove in Bottom Plate (Part 2) faces the rear
and aligns with the grooves in the Left & Right Side Panels.
Left Side Panel
Right Side Panel
Bottom Plate
Cam Lock
Long Screw-In Pegs
Dowel Pegs
Bottom Support Feet (Part M)
STEP 4: Attach Bottom Support Feet (Part M) onto pre-
marked holes on Bottom Plate using (8) 3.5 Screws
3.5 Screws

STEP 5
STEP 6
D*4
（7）
（7）
（10）
（10）
（8）
（9）
D
D
D
D
STEP 5: Carefully place frame into an upright position. Place the
Lower Rear Panel (Part 9) into the grooves on the Left & Right Side
Panels and slide down into the groove on the Bottom Plate. Once
seated place the Upper Rear Panel (Part 8) into the grooves on the
Left & Right Side Panels and slide down until it meets the Lower
Rear Panel.
Note: Ensure Lower Rear Panel Is Fully Seated Into Grooves On Bottom Plate
Cam Lock
Cam Lock
Cam Lock
STEP 5A: Ensure Cam Locks (Part D) are inserted
in holes with open side facing outwards toward
receiver hole for Screw-In pegs (Arrow Side). Insert
Short Screw-In Pegs on the Inner Support Fascia
(Part 10) into the Cam Locks (Part D) on the Inner
Support. Turn Cam Locks clockwise to tighten.
STEP 5B: Ensure Cam Locks (Part D) are inserted
in holes with open side facing outwards toward
receiver hole for Screw-In pegs (Arrow Side). Insert
Short Screw-In Pegs on the Inner Support Fascia
(Part 10) into the Cam Locks (Part D) on the Inner
Support. Turn Cam Locks clockwise to tighten.
Inner Support
Inner Support

STEP 7
STEP 8
D*4
D*8
E*28
（1）
D
D
D
D
DD
D
D
D
（10）
（10）
STEP 7: Ensure Cam Locks (Part D) are inserted in holes with open side facing outwards
toward receiver hole for Screw-In pegs (Arrow Side). Slide Inner Supports onto Long Screw-In
Pegs on the bottom plate ensuring that the Front Fascia are facing Left and Right (See
Diagram). Turn the Cam Locks (Part D) clockwise to tighten.
Long Screw-In Pegs
Slide Down Onto Screw-In Pegs
Slide Down Onto Screw-In Pegs
Ensure Inner Support
Fascia Is Facing Left
Ensure Inner Support
Fascia Is Facing Right
Cam Lock
Covers
Cam Lock
STEP 8A: Ensure Cam Locks (Part D) are inserted in holes
with open side facing outwards toward receiver hole for Screw-
In pegs (Arrow Side). Place Top Plate (Part 1) onto the
assembled frame. Confirm that all Long Screw-In Pegs and
Dowel Pegs that were preassembled in STEP 1 are seated
correctly. Door Strike Plates should be facing the front and the
groove on the underside of the Top Plate should be seated
completely on the Upper Back Panel. Turn the Cam Locks (Part
D) clockwise to tighten.
Top Plate
STEP 8B: Cover all Cam Locks with
Cam Lock Covers (Part E)

STEP 9
STEP 10
（15）
（15）
（15）
（15）
I
I
H
H
L
L
L
L
F
*2
F *2
F *2
F *2
I
H
L *4
F *8
F *4
F *4
F *16
Door Knob
Screw
Hinges Door
Knob
3.5 Screws
STEP 9A: Attach Hinges (Part L) to the inside of the Front
Doors (Part 15) using (8) 3.5 Screws
STEP 9B: Attach Door Knobs (Part I)
to Front Doors using (2) Door Knob
Screws (Part H)
3.5 Screws
STEP 10: Attach Front Doors (Part 15) to pre-marked holes in
TV Stand using (16) 3.5 Screws

STEP 11
STEP 12
（3）
（3）
（4）
K *12
G *8
G
G
G
G
G
G
G
G
K
K
K
Shelf Holders
STEP 11: Insert Shelf Holders (Part K) into holes at the desired
height then place the Left & Right Shelves (Part 3) and the Middle
Shelf (Part 4) onto Shelf Holders
Back Panel Screws
STEP 12: Attach Upper and Lower Back Panels to the
Inner Supports using (8) Back Panel Screws