Bracketron Mvm-45-05 User manual

INSTALLATION MANUAL

MITSUBISHI - LANCER - 2002-2006

MITSUBISHI - OUTLANDER - 2002-2006

Mount Location: To The Right of the Radio

FOR

MVM

Multi Vehicle Mount

MVM-45-05

Thank you for purchasing your new Bracketron MVM Multi Vehicle Mount.

The Multi Vehicle Mount is an (end user-installer) modiﬁ able professional mounting

bracket for most all mobile electronics requiring a steady and secure installation in a mo-

tor vehicle. The MVM installs behind your vehicles dash panel using existing or non-vis-

ible holes and is designed to cleanly protrude out from your vehicle’s dash panel.

Before installing, you must take the time to read and understand this installation manual

and read all the warnings accompanying this product.

Instructions Include: tools needed for install, directions for dash panel removal, directions

for modifying the MVM if required.

You can download this manual and any updates from

http://www.bracketron.com/downloads

Includes PHS-203 Ultra Slim Swivel

IMPORTANT INFORMATION

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

MVM Instructions | Page 1

IMPORTANT INFORMATION

Please read instructions completely before installing this Bracketron MVM Mount. All instructions are written from the drivers seat van-

tage point looking forward at the vehicles dash. We advise caution whenever you are removing or handling plastic parts of a vehicles

dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.

PARTS INCLUDED: MVM-45-05 Mount, 3 - #8x3/4” Self Tapping Screws, 2 - M4x8 Phillips Pan Head Screws, 2 - M4 Nylon Stop

Nuts, PHS-203 Ultra Slim Swivel and Mounting Hardware.

TOOLS NEEDED FOR MVM MODIFICATION (if required)

4 inch Mounted Bench Vise

12 oz. Ball Pein Hammer

Standard Tin Snips

Small File

TOOLS NEEDED FOR DASH PANEL DISASSEMBLY

Dash Trim Tool (Part #SIT-104)

# 2 Phillips Screwdriver

9/32” Open End Wrench (for swivel)

Marking Pen

DASH DISASSEMBLY INSTRUCTION

Locate and remove three climate control knobs. Note: Pull straight

outwards to release these knobs. Remove the two Phillips screws on the

outside knob controls. Once all three knobs and two screws are removed

and set aside carefully, use the Dash Trim Tool (#SIT-104) to remove the

dash trim bezel. Set the bezel aside carefully.

Skip to Step 5 on the following page if you have not yet formed the

bracket to ﬁt your vehicle.

Locate and remove two screws from the right of the radio. Set screws

aside in a safe place. Place part “A” of the MVM over existing screw

holes and replace factory screws as shown in middle picture on the left.

When smaller part “A” is secure, reinstall the dash trim bezel in reverse

order securing all clips and screws. Reinstall the screws that secure the

climate control bezel, and also reinstall all three control knobs.

Once dash bezel is secure, connect part “B” to part “A”. Use the two (2)

M4x8 Pan Heads screws provided and Nylon Nuts and tighten part “B”

to part “A” with a 9/32” open end wrench and Phillips screwdriver.

Install the included Ultra Slim Swivel #PHS-203 to your Multi Vehicle

Mount or any other AMPs compatible device.

Your installation is complete

Install Mount Here

Note: The hole pattern on the face of the MVM maybe

different then what is shown in the pictures.

Outlander Shown

Outlander Shown Above

Lancer Shown

Connect A&B

Picture 2

Picture 1

MVM MODIFICATION INSTRUCTIONS

MVM Instructions | Page 2

Begin by using the Ball Pein Hammer to ﬂ atten the bend area

shown in Picture 1. Use your vises ﬂ at anvil area to pound the

mount ﬂ at.

Locate the strait line notch between the four holes on the side

of the MVM. Place this line so it is horizontal with the jaws of

your vise. Tighten the vise and bend in one direction to allow the

notched area to snap clean apart. Note: You may have to pound

the edges of the two peices ﬂ at a little bit. You have now created

part (A) and part (B). See picture 2 at left.

Place part (A) back into the vise. See picture 2 at left to see where

to bend a 90 degree right angle. Note: you may need to enlarge

the middle hole to accomodate a small plastic pin. You can do this

with a small ﬁ le. Take a small ﬁ le and clean up any rough edges if

needed. Black paint or marker can be used to touch up any areas

that show bare metal.

Return to step 2 on page 2 to continue installing the MVM.

The Bracketron MVM-45-05 mount is a modiﬁ able mounting bracket. The illustrations on the left show how this mount should

look during and after the modiﬁ cation steps in order to ﬁ t the listed vehicles on the front page of this manual. Many vehicle

applications may not require any modiﬁ cations to the mount. If this is the case it will be noted below and there will be no steps

to follow on this page.

PLEASE NOTE

The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor

do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.

Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable

for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.

Note: Please see page 3 in this manual for PHS-

203 Ultra Slim Swivel Instructions.

Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439

tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443

email: [email protected] web: www.bracketron.com

Bend Mount

Picture 3

Note: The hole pattern on the face of the MVM maybe

different then what is shown in the pictures.

(A)

(B)

Flatten Mount Here

Bend 90 Degree Right Angle

Notch A Larger Hole

2.25

(A)

(B)

PHS-203 ULTRA SLIM SWIVEL INSTRUCTIONS

MVM Instructions | Page 3

PLEASE READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON MOBILE SOLUTION.

This Professional Swivel Mount Solution is designed to be mounted to your MVM or any other 4 hole AMPs compatible mounting

device. The Ultra Slim Swivel is compact with a low proﬁ le and is designed to provide adjustability to devices such as Satellite

Radio Receivers, GPS monitors or Mobile Phones. The Ultra Slim Swivel angles your device for better viewing, tilting approx 15°

in all directions and swivels 360° degrees for maximum adjustability. All mounting hardware is included in the kit along with our

AMPs adapter plate to attach devices that support T- Notch mounting.

PARTS INCLUDED

1 - Ultra Slim Swivel

1 - AMPs Adapter Plate

4 - M4 x 10 Hex Head

Screws

4 - M4 x 10 Pan Head Screws

4 - M4 x 12 Pan Head Screws

4 - M4 Hex Head Nuts

4 - M4 Nylon Locking Nuts

4 - M4 Star Washers

1Note: The swivel can be installed before or after the mount is installed

in the vehicle. Attach the Ultra Slim Swivel to any MVM or CBM Mount or other AMPs

mounting device by inserting the M4x10 Pan Head screws through the holes on the

back half of the swivel. Align the screws up with the holes on the mount. Attach the M4

Nylon Locking Nuts only ﬁ nger tight. Rotate the front half of the swivel to gain access to

the M4x10 Pan Head screws. (See Picture 1&2) Tighten all 4 screws with a #2 Phillips

screwdriver and 9/32” open end wrench.

Picture 1 Picture 2

Rotate

Adjust Hold Tension

2Tighten the center screw to adjust the desired tension of the swivel. (See

Picture 3) Note: If Swivel becomes loose over time, you can grasp the

swivel and pull toward you lightly while rotating it clockwise. This will

tighten the swivel allowing you to create the desired tension needed.

Picture 3

Attach the AMPs T- Notch Adapter to the front half of the swivel

using the M4x12 Pan Head screws. Attach the M4 Star Washers and

M4 Hex Nuts to the screws and tighten the plate down with the #2

screwdriver and 9/32” open end wrench. Slide your device onto the

T- notch Adapter plate to secure it to the swivel. (See Pictures 4)

For T- Notch Devices

Picture 4

Picture 5

Attach your AMPs device using the M4x10 Hex Head screws and M4

Star Washers. Align the holes on the device with the holes on the front

half of the swivel. Slide the Star Washers onto the Hex Head screws.

Insert the screws through the swivel and into your device only ﬁ nger

tight. Tighten down the device with the 9/32” open end wrench.

Your device is now secure to the swivel. (See Pictures 5)

For AMPs Devices with Inserts

The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor

do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.

Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable

for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.

Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439

tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443

email: [email protected] web: www.bracketron.com

Table of contents

Other Bracketron Rack & Stand manuals