Sterling Pro SP1HC GR Operator's manual

BACK BAR BOTTLE COOLER
USER INSTRUCTION MANUAL
Please keep in safe place
for future reference

INTRODUCTION
Thank you for purchasing a Sterling Pro Bottle Cooler. The range has been designed and
manufactured to high standards to give a long and reliable life.
Please read carefully the contents of this manual and ensure installation and operation
instructions are followed. Failure to comply with instructions may cause operational faults
or affect your warranty.
USE AND RESTRICTIONS
The Sterling Pro coolers have been designed to chill pre-packaged bottled or canned drinks
only.
The cabinets are designed for indoor use only in ambient temperatures from +12OC to +32OC
65% humidity.
INSTALLATION
Please follow these instructions carefully, if the appliance is installed incorrectly then the
performance and reliability will be reduced.
Electrical installation should only be carried out by a suitable trained person.
INSPECTION
Inspect the appliance for any superficial damage on receipt and record any findings on the
Carrier’s delivery note also notify your supplier immediately. You have 24 hours to report
damage to your retailer.
HANDLING
Do not drag the appliance, transport with a suitable padded sack barrow; do not put
pressure onto the glass doors.
Keep the appliance vertical and on its base; do not tip upside down. If the appliance has been
tipped onto its back, side or front then leave the cabinet standing on its base for 2 hours before
switching on.
LOCATION
Place the appliance on a flat level surface in a well ventilated position away from any heat
sources. It should not be exposed to any water spillage, spray, steam or high humidity. The
appliance can be placed under a work top providing there is at least 40mm clearance to the
sides 50mm to the rear and 20mm to the top of the cabinet. The greater the ventilation around
the cabinet the lower its energy consumption will be. The front grill must be kept clean and
clear at all times to ensure optimal cooling.
ELECTRICAL CONNECTION
This appliance must be earthed; do not switch on until installation has been completed.
The appliance comes with a factory fitted supply lead complete with a 13A 3 pin plug therefore
it only needs to be connected to a suitable power point.
A power socket of type earthed 13A 240V and protected by a RCCB (residual current circuit
breaker) should be used which is easily accessible for the isolation of the appliance.
The socket should be installed in accordance with current I.E.E. regulations if in doubt contact
a qualified electrician.

OPERATION
Do not switch power on and off in quick succession as this will damage the compressor and
cause the appliance to fail.
After completing electrical installation, power can be switched on at the mains.
On power up the compressor and fans will start and the internal light should illuminate
(ensure light switch is on).
The temperature is controlled by a thermostat which is factory set at position 3 this should not
need adjusting. The cabinet should be left on at all times
Ensure doors are kept closed when not serving failure to do so will cause the cabinet to
have reduced efficiency and will cause condensation and ice build up on the cooling plate.
If excess ice builds up switch cabinet off and allow it to defrost. Remove any excess water from
inside the cabinet.
MAINTENANCE
Please note; maintenance or cleaning should not be carried out while the appliance is
connected to the power supply.
(Due to electrical regulations only a limited amount of user maintenance can be carried out.)
LIGHT AND STARTER
To replace the lamp and or starter switch, turn the cabinet off and un-plug. Remove the lamp
cover then simply twist lamp/starter to remove, replace new in reverse.
CLEANING
Both the interior and exterior can be wiped cleaned with a warm damp cloth do not use
abrasive cream cleaners.
For sliding door cabinets the door channels should be wiped clean every week and any spillage
should be removed immediately
All other maintenance should be carried out by a properly trained and qualified person.
It is recommended that the condenser is cleaned at least once every 12 months. Access is
from the rear of the cabinet by the removal of the right cover panel. The condenser should be
brushed with a stiff brush and debris should be removed with a vacuum cleaner. Note the
cabinet should be disconnected from the supply before any panel is removed. Failure to
remove the cabinet can result in the warranty being made void.
DISPOSAL
The crossed out wheeled bin symbol means that within the European Union the product must
be taken to a licensed disposal recycling facility.
Do not dispose of these products as unsorted municipal waste.

FAULT FINDING
The appliance is leaking:
- Check cabinet is level, try tilting back slightly. The cabinet should be slightly higher at the
front to encourage any moisture from the defrost programme running to the rear of the
unit. To be evaporated from the rear tray, this can be done by adjusting the front feet.
The appliance does not start:
- Check the plug is correctly inserted and the socket is switched on
- Check that there is power at the socket
- Check the fuse
The cabinet is too warm:
- Check the thermostat is not set too low
- Check the doors are closing
- Check the air vents condenser are not blocked check ambient is not above 32OC
or below 12OC
The cabinet is too cold:
- Check the thermostat is not set too high
The back of the cabinet is iced up:
- Check the thermostat is not set at maximum check the doors are fully closing
- Check the humidity is below 65%
The appliance is noisy:
- Check the cabinet is level
- Check it is not in contact with other coolers or parts
The light does not work:
- Check the switch is on
- Check the lamp is in place
- Renew lamp
- Check starter is in place
- Renew starter
Doors no not close:
- For sliding doors check channels are clear of debris or any sticky residue from spillages
- Check cabinet is level
SP1HC/
SP1BC
GR
SP1HC/
SP1BC
BK
SP2HC/
SP2BC
GR/HG
SP2HC/
SP2BC
BK/HG
SP2HC/
SP2BC
GR/SL
SP2HC/
SP2BC
BL/SL
SP3HC/
SP3BC
GR/HG
SP3HC/
SP3BC
BK/HG
SP3HC/
SP3BC
GR/SL
SP3HC/
SP3BC
BK/SL
EXTERNAL
Height mm 900 900 900 900 900 900 900 900 900 900
Width mm 600 600 900 900 900 900 1350 1350 1350 1350
Depth mm 520 520 520 520 520 520 520 520 520 520
INTERNAL
Height mm 750 750 750 750 750 750 750 750 750 750
Width mm 500 500 800 800 800 800 1250 1250 1250 1250
Depth mm 395 395 395 395 395 395 395 395 395 395
CAPACITY
330ml bottles 106 106 180 180 180 180 260 260 260 260
VOLTAGE 240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
240V/
50Hz
CURRENT 1.3A 1.3A 1.5A 1.5A 1.5A 1.5A 2.1A 2.1A 2.1A 2.1A
POWER 180W 180W 230W 230W 230W 230W 400W 400W 400W 400W