Sterling ClearWater TAKU TAK10 User manual

T h e c l e a r choic eT h e c l e a r choic e
TAKU
Fitting Instructions and Parts List
Please read these instructions before you install and use the tap, be sure to
keep them safe for future reference and to request replacement parts.
All designs, descriptions and dimensions are subject to change without notice.
Please Keep Me Safe
AFTER CARE
To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean,
soft damp cloth. A solution of warm water and a mild liquid detergent may be used where
necessary, and then the fitting rinsed thoroughly and wiped dry. Abrasive cleaners, scouring
cleaners and acid cleaners must not be used under any circumstances. All bath cleaning
powders and liquids will damage the surface of your fitting even the non-scratch cleaners.
Avoid contact with all solvents and any harsh household chemicals. You will damage the
finish and void your guarantee.
GUARANTEE AND LIABILITY
In the unlikely event that you should experience any defect in the material or workmanship of
your mixer tap within 5 years of purchase, we will replace the faulty part free of charge.
Decorative surface finishes are guaranteed for one year from the date of purchase provided that
our advise concerning care has been observed and no scouring agents have been used. This is
provided that the mixer or tap has been used for normal domestic purposes in the UK and that
the care, installation and maintenance instructions have been observed.
Scuff and scratches caused by normal wear and tear, improper installation or accidental
damage are excluded from this guarantee.
You should retain a copy of your dated invoice as proof of purchase to validate any claims
under this guarantee.
No other warranties, express or implied, are made, including merchantability or fitness for a
particular purpose.
The c lear choiceThe clear choice
Fitting Instructions and Parts List
Please read these instructions before you install and use the tap, be sure to
keep them safe for future reference and to request replacement parts.
All designs, descriptions and dimensions are subject to change without notice.
Spare Parts and Service
Contact: Sterling
Phone: [phone]
Fax: [phone]
Email: [email protected]
Website: www.sterling.eu.com
TAKU
265
187
162
265
162
187

In the unlikely event you nd a part missing please contact our Customer Service Helpline on
01684 299555 for immediate despatch of part.
MAINTENANCE
REMEMBER
TAKU
TAK10
IF THE FITTING BEGINS TO DRIP
1Turn off the water supply
2Loosen grub screw under handle, remove handle and valve
3Carefully clean seating, rubber washer and ceramic disc
4Replace valve and handle, then turn on the water supply
5If problem persists contact our helpline quoting the product code
Where an aerator is fitted to the outlet of the spout, it will need occasional cleaning.
This will be evident when the water flow slows down to an unacceptable level. To accomplish
this unscrew the outlet in an anti-clockwise direction and remove the mesh. Immerse the mesh
in a suitable descaling fluid overnight, rinse throughly in clean water and re-install.
Maximum water supply pressure 5 bar (75PSI) Minimum water supply pressure 0.3 bar
Maximum hot water supply temperature 70˚C
Recommended hot water supply temperature 65˚C
If these temperatures or water pressure are exceeded, damage to the tap can result. A pressure
reducing valve may be required to be fitted in high water pressure situations.
PREPARATION
INSTALLATION
It is very important that you read through the following instructions
BEFORE you install and use the tap.
Screw the flexible hoses (hot flexible hose on the front) into the mixer body, and fully
hand tighten.
Pass the flexible hoses and threaded stud through the sink top from above and place the
mixer in position on the sink.
Slide the flat washer and fixing nut up the flexible hoses, and then screw the nut all the way
up making sure the tap is in the correct position.
Connect the check valve group to the cold water inlet pipe first, and then to the cold end
Flexible hose.
Having first checked all the new connections, turn on the mains stop cock, close all taps
except the new mixer and as the system starts to refill check for leaks.
Make sure that sealing washer has been fitted to the mixer body.
(Note:The thickness of sink＞35mm no need to use the mounting seat.)
We strongly recommend installing particle filters and isolation valves to both hot and cold feeds.
This will help to prevent premature failure of valves and make any future maintenence easier.
Flush the plumbing system before installing the mixer tap. This is to void plumbing residues
clogging the mesh of the aerated outlet, or possibly damaging the valve’s washers. This is
especially important where extensive plumbing work has been carried out.
First shut off your water heating system then, with your mains stop cock closed, open the lowest
hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty.
(The hot water storage cylinder always remains full).
Ster0179CP/BN/BB/MB
Ster0180CP/BN/BB/MB
Ster0034
Ster0165
Ster0166
Ster0170
Ster0184CP/BN/BB/MB
Ster0211
Ster0107
Ster0169CP/BN/BB/MB
Ster0183
Ster0033
Ster0181
Before installation, please confirm whether the copper tube (Ster0170) is tightened, and
tighten it with a wrench.