STODDART WB.KO1 User manual

Revision Date: 25/10/2019
A guide on the use, care and maintenance
of your quality Stoddart product
Specification, Installation
and Operation Manual
KNEE OPERATED WASH BASIN
Model:
WB.KO1, WB.KO2, WB.KO3

Page Intentionally Left Blank
Page 1
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz

Page 2
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Recommendations � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Responsibilities� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Attention � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
General Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Referenced Australian Standards � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Installation
WB�KO1 Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Water & Waste Requirements
Installation
WB�KO2 Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Water & Waste Requirements
Installation
WB�KO3 Installation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
Water & Waste Requirements
Installation
Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
Water does not switch off or water continues to run from outlet after timed out
Water runs for too short or too long
Water flow from outlet is too little
Water leaks onto floor under basin
Maintenance
Spare Parts� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
SPPL.WB.KO1
SPPL.WB.KO2
SPPL.WB.KO3
Cleaning Instructions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12

Page 3
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Recommendations
Responsibilities
SPPL�WB�KO1 SPPL�WB�KO2 SPPL�WB�KO3
Upon receiving a Stoddart product, inspect immediately for any visible signs of shipping damage and notify the carrier immediately�
When removing the product from its packing, be careful not to dent or scratch outer surface� Any concealed damage should be noted
and reported immediately to the freight carrier� A claim should be filed with carrier if appropriate�
Stoddart thoroughly inspect all products that are despatched from our factory�
The Plumber is responsible to ensure that the system is installed in accordance with all specific requirements of local codes and
regulations (including AS 3500)�
If questions or complications should arise during the installation of a Stoddart product that cannot be solved using the accompanying instructions,
please contact our offices or local representatives�

Page 4
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance� Keep this booklet on
hand in a safe place for future reference by other operators or users�
Stoddart design, manufacture & distribute Food Service Equipment (appliances) and Plumbing products
exclusively for the commercial market.
This unit is not designed nor intended for household or domestic use & must not be used for this purpose.
• All units MUST be installed according to the procedures stated in the installation section of this manual
• In the case of new personnel, training is to be provided before operating the equipment
• DO NOT use this unit for any other purpose than its intended use
• Keep fingers out of “pinch point” areas
• Do NOT remove any cover panels that may be on the unit
• If any fault is detected, refer to troubleshooting
• The manufacturer declines any liability for damages to persons and/or things due to an improper/wrong and/or unreasonable use of the
machine
Read these instructions carefully and retain for future reference�
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind occurred to persons, units
or others, due to abuse and misuse of this unit in regards to installation, un-installation, operation, servicing or maintenance, or lack of
conformity with the instructions indicated in this documentation�
Disclaimer
All units made by the manufacturer are delivered assembled, where possible, and ready to install� Any installation, un-installation,
servicing, maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply in
accordance to this documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY�
The manufacturer cannot be held responsible or liable for any unauthorized modifications or repairs� All modifications or repairs must
be approved by the manufacturer in writing before initiating� All modifications or repairs performed to this unit must be performed at all
times by a TRAINED AND AUTHORISED SPECIALIST�
Attention
General Information
Referenced Australian Standards
Design Design for access
Design & fit out of Food Premises
AS 1428.1 – 2009
AS 4674 - 2004
Markings & Labels Watermarked components must have Watermark logo and license.
Copper alloy products marked ‘DR’
AS 3500.1-2003
AS 5200.000 – 2006 Appendix B
AS 6400 – 2005 Clause 2.4.6
AS 2345 - 2006
Dezincification resistance Dezincification resistance applicable to copper alloy components in
contact with mains water
AS 2345 - 2006
Contamination of water Products For Use In Contact With Drinking Water AS 4020 - 2005
Pipes and Fittings Dimensional compliance with relevant or corresponding Australian
Standard for the pipe or fitting
AS 3688 - 2005
Joints (i.e. Spigots, sockets, flanges,or other
joint components, where interfacing other
authorised components)
Dimensional compliance with relevant or corresponding Australian
Standard for the pipe or fitting Pipe Threads of Whitworth Form. – Part 2
Fastening Pipe Threads
AS 3688 - 2005
Installation Warranty / Installation instructions shall be provided by
the manufacture
AS3500.2 - 2003

Page 5
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
WB.KO1 Installation
Water & Waste Requirements
Installation
• Flow pressure 300kPa – 500kPa
• Max� static pressure 800 kPa
• 15mm water supply connection (Isolation valve & Braided hose supplied by others)
• Waste connection is NB40� Trap provided by others
*Pipe work to the valve fixture must be sized to and installed to water service rules and regulations (AS/NZS 3500�1 and local regulations)� To
ensure proper sizing of the pipe work it is recommended to engage a qualified hydraulic designer�
1� Remove the packing from the wash basin and check for damage
2� Unscrew the screws on either side of the basin� Remove the wall mount bracket from the basin
3� Place the bracket at desired distance from basin top� Ensure the bracket is level, mark the screw hole locations and/or outline around
the bracket if adhesive is to be used
4� Ensure the water supply and waste are in the zone marked in the image to the right, and the waste is approximately 226mm from the
top of the basin�
5� Attach bracket to the wall with sufficient load bearing fasteners
6� Slide the wash basin on to the bracket & replace the screws on either side of basin (do not overtighten screws)
7� Ensure water lines have been thoroughly flushed before connecting to valve
8� Connect supply to inlet
9� Clean stainless steel surfaces
226mm
Plumbing Inlet /
Waste Outlet
Water Supply Isolation Valve
& Braided hose
Mounting bracket
(supplied tted to basin)

Page 6
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
WB.KO2 Installation
Water & Waste Requirements
Installation
Installation
• Flow pressure 300kPa – 500kPa
• Max� static pressure 800 kPa
• 15mm water supply connection (Isolation valve & Braided hose supplied by others)
• Waste connection is NB40� Trap provided by others
*Pipe work to the valve fixture must be sized to and installed to water service rules and regulations (AS/NZS 3500�1 and local regulations)� To
ensure proper sizing of the pipe work it is recommended to engage a qualified hydraulic designer�
1� Remove the packing from the wash basin and check for damage
2� Unscrew the screws on either side of the basin and the access panel� Remove the wall mount bracket and access panel from the basin
3� Place the bracket at desired distance from basin top� Ensure the bracket is level, mark the screw hole locations and/or outline around
the bracket if adhesive is to be used
4� Ensure the water supply and waste are in the zone marked in the image to the right, and the waste is approximately 226mm from the
top of the basin�
5� Attach bracket to the wall with sufficient load bearing fasteners
6� Slide the wash basin on to the bracket & replace the screws on either side of basin (do not overtighten screws)
7� Ensure water lines have been thoroughly flushed before connecting to valve
8� Connect supply to inlet
9� Replace access panel (do not overtighten screws)
10� Clean stainless steel surfaces
226mm
Plumbing Inlet /
Waste Outlet
Removable Mounting Bracket
(supplied tted to basin)
Fixed Mounting Bracket
(supplied tted to basin) Water Supply Isolation Valve
& Braided hose

Page 7
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
226mm
Plumbing Inlet /
Waste Outlet
Water supply stop cock
& Braided hose
Removable Mounting Bracket
(supplied tted to basin)
Fixed Mounting Bracket
(supplied tted to basin)
WB.KO3 Installation
Water & Waste Requirements
Installation
1� Remove the packing from the wash basin and check for damage
2� Unscrew the screws on either side of the basin and the access panel� Remove the wall mount bracket and access panel from the basin
3� Place the bracket at desired installation height� Ensure the bracket is level, mark the screw hole locations and/or outline around the
bracket if adhesive is to be used
4� Ensure the water supply and waste are in the zone marked in the image to the right, and the waste is approximately 226mm from the
top of the basin�
5� Attach the upper wall bracket to the wall with sufficient load bearing fasteners
6� Slide the wash basin on to the bracket & replace the screws on either side of basin (do not overtighten screws)
7� Ensure water lines have been thoroughly flushed before connecting to valve
8� Connect supply to inlet
9� Attach the lower wall bracket to the wall with sufficient load bearing fasteners
10� Replace access panel (do not overtighten screws)
11� Clean stainless steel surfaces
• Flow pressure 300kPa – 500kPa
• Max� static pressure 800 kPa
• 15mm water supply connection (Isolation valve & Braided hose supplied by others)
• Waste connection is NB40� Trap provided by others
*Pipe work to the valve fixture must be sized to and installed to water service rules and regulations (AS/NZS 3500�1 and local regulations)� To
ensure proper sizing of the pipe work it is recommended to engage a qualified hydraulic designer�

Page 8
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Troubleshooting
Water does not switch off or water continues to run from outlet after timed out
Water runs for too short or too long
Water flow from outlet is too little
Water leaks onto floor under basin
• Check Front panel has some free play; Make sure there is a 2mm gap between push rod and push panel (valve must be able to travel
freely to fully close) – if not adjust push rod
• Check that a line strainer or filter is installed & is clean
- If a line strainer is installed, & has contaminants present – could some have got through to valve seat? Check Valve Cartridge�
- If a Line strainer is not installed, check for dirt and grit in valve cartridge
• If above checked out o�k� contact service
Note: Cartridge is a service part & not covered by warranty if damaged by dirt in water� Stoddart Recommend Customers install a line
strainer/ filter to protect the valve�
• AS4676 requires min� 15 seconds for hand washing� CMPL�0938 is designed to run 15 – 30 secs
• Make sure there is a 2mm gap between push rod and push panel & rod slides freely
- If gap it too big, valve might not get pushed in fully giving short cycle
- If rod doesn’t slide freely, it may cause the valve to take longer to time out
• Check position of circlip on valve spindle; inner = short, outer = long
• Check water pressure; low water pressure = longer time
• Check ¼ turn stop-valve in inlet of valve� Partially closed may slow time adjustment of valve
• Check supply pressure and stopcocks are open
• Check lines are not flattened or kinked
• Check plumbing connections – tighten as required
• Check seal between spout and basin – replace seal or apply silicon sealant
• Check valve spindle (valve stem seal) – replace faulty cartridge

Page 9
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Maintenance
Spare Parts
SPPL.WB.KO1
Part No Description
CMPL-0255 Waste and Plug
CMPL-0938
Valve Housing (complete)
Valve Cartridge (15 – 30 seconds) tted as Standard
Valve Cartridge (5 – 7 seconds) alternative spare part
CMGE�0510 Spring for Push Basin front panel
CMPL-0836 Strainer;In-Line;Brass;1/2” BSP

Page 10
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Maintenance
SPPL.WB.KO2

Page 11
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
SPPL.WB.KO3
Maintenance

Page 12
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Cleaning Instructions
• All surfaces of the product should be cleaned with mild soap and water or a neutral product
• Carefully rinse away all surplus cleaning product
• IMPORTANT: Never use harsh or abrasive cleaners on stainless steel� Do not use chlorinated or bleach water
Maintenance

Page 13
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz

Page 14
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz

www.stoddart.com.au
International
Sales
Tel: [phone]
Email: [email protected]
Service / Spare Parts
Tel: [phone]
Email: [email protected]
Email: [email protected]
www.stoddart.co.nz
New Zealand Business Number: 6837694
New Zealand
Sales
Tel: [phone]
Email: [email protected]
Service / Spare Parts
Tel: [phone]
Email: [email protected]
Email: [email protected]
www.stoddart.com.au
Australian Business Number: 16009690251
Australia
Sales
Tel: [phone]
Email: [email protected]
Service / Spare Parts
Tel: [phone]
Email: [email protected]
Email: [email protected]