Streamline Streamrack VG-RS126 User manual

STREAMLINE
VG-RS126
Streamrack
Code:
Product:

INSTRUCTION MANUAL
INSTR-VG-RS126
English

2W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
STREAMLINE
®
Safety Regulations Use
Recommended Fixing Method
Required PPE
Warnings General
• Sharp edges
• Moving Components
• Pinch Risks
• Weight when moving
• Fall Risk
• Must be tied down in van
• Do not exceed a weight of 25kg when loading each shelf.
• Large objects should be secured in place during transit to prevent damage to
the racking unit.
• Do not climb on racking unit.
• Note: Extra caution should be taken when drilling holes into a vehicle. Take
care not to damage the bodywork or vital elements of the vehicle
when drilling.
• Position the vehicle in the desired location in the vehicle, if this is over a
wheel arch, the height configuration of the racking will need to be changed
(see below).
• Once positioned, measure the location of the floor brackets from the back
and side of the van. use these measurements to then check that he underside
of the van is clear from obstruction for drilling.
• Mark the hole centres of the fixing points on the floor brackets, three holes
should be marked on either side, with at least an additional 3 along the long
side of the unit. Move the racking to drill 8mm dia. holes in the
correct positions.
• Replace the racking unit in position and secure using M6x50 bolts and
washers, with M6 nylon nuts and washers fastening the bolts from the under
side of the van.
• The back panel of the racking should be securely fixed to the wall panels of
the van. It is recommended that all fixings should be to the inner skin of th
vehicle, not the wooden lining. Care should be taken that there is enough
space between the inner and outer skins to not damage the bodywork of
the vehicle.
• The shelf units have dedicated holes which can be used to secure them to the
walls of the vehicle. Ensure that the fixing points are free from obstruction
before drilling.
• Use suitable length M6 bolts with M6 washers and nylon nuts to secure the
racking unit.
Additional protective equipment such as a dust mask, non-skid safety shoes, hard hat
or hearing protection may be required depending on the safety regulations in the
operator surroundings.
Use personal protective equipment to avoid personal injury:
Protective Gloves Protective Footware

4W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
Streamline® Warranty
The warranty on all Machines and Equipment is
for 1 year (12-months) from RECORDED DATE
OF PURCHASE.
THIS WARRANTY EXCLUDES NORMAL
MAINTENANCE ITEMS, including but not limited
to HOSES, FILTERS, O-RINGS,
DIAPHRAGMS, VALVES, GASKETS,
CARBON BRUSHES and damage to motors
and other components as a result of failure to
replace normal maintenance items. THIS LIST
IS NOT EXHAUSTIVE.
If Streamline®receives notice of such defects
during the warranty period, Streamline®
will either, at its opinion, repair or replace
components which prove to be defective.
Replacement parts will only be supplied under
warranty, upon the inspection and approval of
the defective parts by Streamline®.
Should it be necessary to supply replacement
parts before the opportunity to inspect, these
will be charged at current prices and credit will
only be issued upon subsequent inspection and
warranty approval by Streamline®.
The customer is responsible for the cost of
return of the defective part. If warranty is
approved, Streamline®will pay for the cost
of the repaired or replacement part.
This warranty excludes the following conditions
and circumstances which are at the discretion
of Streamline®:
Wear and tear, misuse, abuse improper
maintenance, frost damage, the use of chemicals
other than those supplied or approved by
Streamline®, improper installation or repair,
unauthorised modification, incidental or
consequential costs, loss or damage, service,
labour or third party charges, the cost of
returning defective parts to Streamline®.
This warranty constitutes the exclusive remedy
of any purchaser of a Streamline®unit and is in
lieu of all other warranties, express or implied,
including without limitation any implied war-
ranty of merchantability or fitness for use, to
the fullest extent permitted by law. In no event
shall any implied warranty of merchantability or
fitness for use exceed the term of the applicable
warranty stated above and Streamline®shall
have no other obligation or liability.
Important
Unfortunately these rights cannot be
transferred to a third party.
STREAMLINE
®
Height Configuration
Maintenance
• The Streamrack is supplied in the low height configuration. It can easily be
changed to give additional height, ideal for being fitted over wheel arches.
• To change the height of the legs, first remove the 4x bolts holding the legs
onto the body of the racking on one side. Each leg has 2x bolts, fitted into
clinch nuts on the shelf unit.
• Once the bolts are removed, slide the legs down until the other set of hole’s
line up with the clinch nuts on the shelves.
• Re-fasten the bolts into the clinch nuts, ensure they are tight but take care
not to over-tighten as this may damage the unit.
• Repeat this for the legs on the opposite side.
• If water is spilled onto the device, wipe it clean with a dry, lint free, non-abrasive cloth to
prolong life
• Regularly check for excessive wear and tear, discontinue use if there is damage to any
fixings or fastenings on the unit.
General

6W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
• STREAMLINE® systems can be built according to customers’ exact requirements
• For non-standard systems, the user’s needs or specifications are listened to and turned
into reality.
• Whilst price is important, quality is remembered long after price is forgotten
• We insist on sourcing brand name products from around the world, only of a reputable
quality, and bring them together under the STREAMLINE® name
• All STREAMLINE® products carry a full one year’s warranty, according to the manufacturers’
standard terms and conditions of sale.
• We have an in-house technical helpline able to answer most of your questions relating to the
capabilities and functionalities of all STREAMLINE® products
• If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately
attend to sending you the correct item and arrange a collection of the wrong item without
any quibbles
• STREAMLINE® is backed by a comprehensive range with massive stocks providing you with a
‘one stop shop’ for all your requirements.
Flexibility
Quality
Service
Why Streamline®?
MANUFACTURED
IN THE
UNITED KINGDOM
CHECKED AND
TESTED BY
QUALITY CONTROL
Notes
STREAMLINE
®

Hamilton House, 8 Fairfax Road,
Heathfield Industrial Estate,
Newton Abbot
Devon, TQ12 6UD
United Kingdom
Telephone: [phone]
Email: [e-mail]
Visit: www.streamline.systems INSTR-VG-RS126