NCR 7360-K780 Manual

Kit Instructions
Sliding Pack Left Hand
7360-K780
Issue A

The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR FastLane SelfServ™ Checkout is a trademark of
NCR Corporation in the United States and/or other countries. Other product names mentioned in this
publication may be trademarks or registered trademarks of their respective companies and are hereby
acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.
EMail: [e-mail]
Copyright © 2017
By NCR Corporation
Duluth, GA U.S.A.
All Rights Reserved

i
Revision Record
Issue Date Remarks
ANov 2017 First release.

Sliding Pack Left Hand
This kit contains sliding pack components for a 3–Bag bagwell module in an
NCRFastLane SelfServ™ Checkout (7360) unit with a Left-hand orientation.
Note: The NCRFastLane SelfServ™ Checkout (7360) can be configured for either Left-
hand or Right-hand orientations, which refer to the direction that customers scan and
bag items. Customers scan from left to right on Left-hand systems, and from right to
left on Right-hand systems.
Kit Contents

2 7360-K780 Sliding Pack Left Hand
Installation Procedures
Installing the Sliding Pack involves the following procedures:
1. Remove Scale Tray on the facing page.
2. Remove Rear Panel on page4.
3. Install Sliding Pack Left Hand on page5.
Note: Before you begin, the leveling feet should set on the floor and must be
leveled.

7360-K780 Sliding Pack Left Hand 3
Remove Scale Tray
To remove the Scale Tray, follow these steps:
1. Lift and remove the Scale Tray from the Bagwell.
Note: The Scale Tray will be installed on the Bagwell after installing the Sliding
Pack.

4 7360-K780 Sliding Pack Left Hand
Remove Rear Panel
To remove the Rear Panel from the Bagwell, do the following:
1. Remove the Scale Tray from the Bagwell. For more information, refer to Remove Scale
Tray on the previous page.
2. Remove nuts securing the rear panel to the Bagwell Frame.
3. Remove the rear panel by pulling it up until it unclips from the Bagwell Frame.

7360-K780 Sliding Pack Left Hand 5
Install Sliding Pack Left Hand
To install the Sliding Pack, do the following:
1. Remove the Scale Tray from the Bagwell. For more information, refer to Remove Scale
Tray on page3.
2. Remove the Rear Panel from the Bagwell. For more information, refer to Remove Rear
Panel on the previous page.
Note: The image below shows that the Scale Tray and Rear Panel has been removed
from the Bagwell.
3. Install rail bracket on the core side and secure it with three M6 flat head screws.

6 7360-K780 Sliding Pack Left Hand
4. Install rail bracket into the side of the bagwell and secure it with two M6 nuts.
5. Install the rear cover panel into the spacer panel and secure it with four M6 nuts.

7360-K780 Sliding Pack Left Hand 7
6. Install the spacer panel with cover panel to the rear side of the bagwell and secure it
with three M6 nuts.
7. Install the two housing bearing as shown in the image below and secure it with two
M5 screws on each housing bearing.

8 7360-K780 Sliding Pack Left Hand
8. Attach the leg support assembly and secure it with three M6 screws.
9. Slide in the two single rails into the housing bearing as shown in the image below.

7360-K780 Sliding Pack Left Hand 9
10. Align the Sliding Pack main frame with the Bagwell.
11. Extend the two rails from the Sliding Pack and align the holes with the mounting
holes of the rail bracket and then secure with five M6 screws on each rail.

10 7360-K780 Sliding Pack Left Hand
12. Install the lock stopper into the spacer panel doing the following.
a. Slide the sliding pack frame until the mounting holes in the spacer panel show
up.
b. Install the lock stopper into the spacer and secure each stopper with four M6
screws.

7360-K780 Sliding Pack Left Hand 11
13. Install the locking assembly on the main frame and secure it with three M6 nuts.
14. Install the stainless steel top tray on the main frame and secure with ten M4 screws.

12 7360-K780 Sliding Pack Left Hand
15. Install the leg support cover and secure it with M4 screws.
16. Install the scale tray to the bagwell by doing the following.
a. Slide the sliding pack frame until the top bagwell shows.

7360-K780 Sliding Pack Left Hand 13
b. Install the scale tray on the bagwell.
17. Adjust the leveling feet of the sliding pack by aligning the rail with the housing
bearing. Ensure that the rail slides smoothly in the housing bearing.

14 7360-K780 Sliding Pack Left Hand
18. Cover all holes using hole cover labels..