Sun King SK-735 User manual

封面封底128克铜版纸，表面过环保漆
内页70g书写纸，全黑白印刷
尺寸：210x142mm
说明书
注意
最后保修内容
做到封底

www.sunking.com
USER MANUAL
MODEL:
SK-735, SK-737,
SK-738, SK-739
24/32/40/43 INCH TV

3
TABLE OF CONTENTS
4. IMPORTANT SAFETY INSTRUCTIONS
5. ASSEMBLING AND PREPARING
6, 7. BATTERY CONTROL UNIT
8. KNOW YOUR TV
9. TV, BATTERY CONTROL UNIT & ANTENNA CONNECTION
10. REMOTE CONTROL
11. OPERATING THE TV
12. SWITCH ON THE TV
SELECT DTV INPUT SOURCE
13. AUTO TUNE CHANNELS
WHEN TV IS TUNING
14. FREE TO AIR CHANNEL LIST
15. PLAYING CONTENT USING USB
16. CHECKING SIGNAL INFORMATION
17. CHANGE VOLUME, CHANGE CHANNEL
18. PICTURE MODE, SOUND MODE
19. TROUBLESHOOTING
TABLE OF CONTENTS

4
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near
water.
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus not operating normally
or has been damaged in any way such
as; the power-supply cord or plug is
damaged, liquid has spilled into it,
objects have fallen into it, or it has been
dropped.
Do not expose to liquid drops or
splashes and do not place objects filled
with liquids, such as vases, cups, etc. on
or over the apparatus (e.g. on shelves
above the unit).
Clean only with a dry cloth.
Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
Only use attachments/
accessories specified by the
manufacturer.
IMPORTANT SAFETY INSTRUCTIONS

5
INSTALLATION PROCEDURE
ASSEMBLING AND PREPARING
1. Open the package and make sure all the accessories are included.
2. Attach the stand to the TV set.
3. Connect an external device to the TV set.
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
• Do not use any unapproved items to ensure the safety and product life span.
• Any damages or injuries caused by using unapproved items are not covered by the warranty.
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
• The items supplied with your product may vary depending on the model.
• Product specifications or contents of this manual may be changed without prior notice due to upgrade of
product functions.
• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39
inches) thick and 18 mm (0.7 inches) width.
• Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into
your TV’s USB port.
CAUTION
NOTE
ASSEMBLING AND PREPARING

6
BATTERY CONTROL UNIT
BATTERY CONTROL UNIT

7
BATTERY CONTROL UNIT INTERFACE
SUN KING™ HOME SYSTEM KEYPAD
SUN KING™ HOME SYSTEM GSM
Sun King™ Home System keypad works as our normal lamps, tokens / keycodes need to be manually entered for it to work.
Clients need to pay via mobile money, receive keycodes, input the keycode into the system, turn it ON, then operate.
Sun King™ Home System GSM is GSM enabled. Meaning it can communicate with the controlling platform, (i.e. Angaza) by
pressing the sync button (which is only visible in the GSM unit). It can be traced or located using satellite signals the same
way as mobile phones. It can also be operated remotely, turning on / off without interacting with the unit physically. When
clients pay Angaza automatically communicates with the units.
BATTERY CONTROL UNIT
1
5 6 7 8
2 3 4
3 4 5 6
1 2
1. GSM signal status
2. Status LED: PAYG indication blinks when keys are pressed
3. Keypad
4. Sync button
5. PAYG days indicator
6. Battery status indicator
7. Solar charge status indicator
8. Long press to switch ON or OFF
1. Status LED: PAYG indication blinks when keys are pressed
2. Keypad
3. PAYG days indicator
4. Battery status indicator
5. Solar charge status indicator
6. Long press to switch ON or OFF

8
KNOW YOUR TV
KNOW YOUR TV
1. TV POWER CABLE CONNECTION PORT Connects your TV to the battery control unit
2. FLASH DISK CONNECTION PORT Connects your TV to external USB devices
3. EARPHONES CONNECTION PORT Connects your TV to an external sound output such as earphones
4. HDMI PORT CONNECTION Connects your TV via HDMI cable
5. VIDEO PORT CONNECTION Connects your TV to an external video/sound source
6. ANT IN DVB-S/S2 Connects your TV to satellite dish
7. ANT IN DTV/ATV Connects your TV to DVB-T/T2, or DVB-C, or analogue aerial to get
clear channel reception
8. CI SLOT Insert the CI card to this slot, to watch the scrambled TV channels
from CI card vendor
TV cable is firmly fixed to the TV then
connected to the battery control unit.
Antenna or satellite cable is
connected to the right port.
1
IMPORTANT
8
HDMIEARPHONEUSBDC-IN LINK LRVIDEO
ANT IN
DVB-S/S2
ANT IN
DTV/ATV
AV IN
1 2 3 4 5 6 7
6 7

9
TV, BATTERY CONTROL UNIT & ANTENNA CONNECTION
TV, BATTERY CONTROL UNIT AND ANTENNA CONNECTION
1. Connect your TV to the battery control unit using the TV cable.
2. Connect your TV to the aerial or satellite dish.
3. Power on the battery control unit.
4. When the TV cable is connected properly to the TV, and the TV is powered by the remote controller or by the power
button on the TV, the power indicator light on the bottom of the TV will glow GREEN.
5. If you subscribe to the pay TV service, you will get one CI module (a big card), along with a smart card (small card). Insert
this CI module to CI slot to watch the related pay channels.
Smart Card
CI Module

10
REMOTE CONTROL BUTTONS
1. Power button: Press to turn ON and OFF
2. TV/Radio: Press to select TV/radio mode
3. PIC: Press to select picture mode
5. Skip backward: Press to go back to
previous scene or track
6. Play or pause: Press to play or pause
track/scene
7. Menu: Press to enter or exit menu mode
9. In ATV/DTV mode, press this button to go
back to the previous channel
12. Exit: Press to exit all on screen display
13. Enter: Press to confirm set up selection
17. Sound mode: Press for audio mode, or
audio language selection
15. Skip forward: Press to go front to the next
scene or track
16. FAV: Press +or -to switch channel from favorite
list, which was added from Programme Edit menu
14. Stop: Press to stop track or scene
18. EPG: Press to show the channel guide
19. Source: Press to display the input source list
10. Mute button: Press to turn the sound OFF
or ON
11. Info: Press this button to display information
about the current mode on the screen
8. Volume: Press up to increase volume
Press down to decrease volume
4. REC: Record TV programs on USB
REMOTE CONTROL

11
TV OPERATION STEPS
OPERATING THE TV
12. SWITCH ON THE TV
SELECT DTV INPUT SOURCE
13. AUTO TUNE CHANNELS
WHEN TV IS TUNING
14. FREE TO AIR CHANNEL LIST
15. PLAYING CONTENT USING USB
16. CHECKING SIGNAL INFORMATION
17. CHANGE VOLUME, CHANGE CHANNEL
18. PICTURE MODE, SOUND MODE
19. TROUBLESHOOTING

12
SWITCH ON THE TV
SELECT INPUT SOURCE
Point the remote to the TV and click on the POWER button on the remote.
Press SOURCE on the remote control. From the Input source displayed user can choose the source from DVB-T,
ATV (analogue TV), and Satellite TV. You can use the up or down to to move to Satellite. Then
press ENTER on the remote to select. Lastly press EXIT button when you are done.
When the user selects the satellite source, they should make sure the dish is set up well. The dish vendor should
help the user set it up (point to the right satellite). To verify it, the user should check the signal strength/quality.
TV will first display no signal
SWITCH ON THE TV

13
AUTO TUNE CHANNELS
WHEN TV IS TUNING
Press MENU on the remote control. Use or buttons to move to select tuning type.
If it is a satellite source, select BLIND SCAN from the tuning type list; if it is another source, select AUTO TUNE.
AUTO TUNE CHANNELS

14
FREE TO AIR CHANNELS LIST
Press ENTER on the remote control. You will see the displayed channel list.
The default setting will be of the TV displaying the free to air channels.
You may use the up down keys up or to move to see more options press ENTER to select.
Press the left/right key to change the group: free-to-air, scrambled, satellite etc.
FREE TO AIR CHANNELS LIST
SORT

15
PLAYING CONTENT USING USB
Insert USB/dongle in the USB port
Press SOURCE on the remote control.
From the input source displayed select Media Player.
You can use the up or down to move to Media Player.
Press ENTER on the remote to select. TV will display contents on the USB FLASH DISK, select item you want to play by
pressing ENTER.
Lastly press EXIT button when you are done.
PLAYING CONTENT USING USB
HDMIEARPHONEUSBDC-IN LINK LRVIDEO
ANT IN
DVB-S/S2
ANT IN
DTV/ATV
AV IN

16
CHECKING SIGNAL INFORMATION
CHECKING SIGNAL INFORMATION
To check the channel’s signal information: Press MENU, scroll down to the signal information (highlighted in blue) then press
ENTER to select. The displayed window will show information of the channel. Ensure your quality is above 30. Incase you do
not have the best quality adjust the positioning of the aerial.

17
CHANGE VOLUME, CHANGE CHANNEL
Press VOL to change sound volume.
Press CH to change/switch the channels.
CHANGE VOLUME, CHANGE CHANNEL

18
PICTURE MODE
SOUND MODE
Press PIC to switch to picture mode or you can change it on the main MENU.
There are four picture modes to choose from:
• Lowlight (long runtime): Only for longer runtime purpose.
• Standard (standard runtime): Suitable for watching the TV in the evening.
• Daylight (short runtime): Suitable for watching the TV during daytime.
• Superlight (very short runtime): Suitable for watching the TV in the sunlight.
Press SOUND to switch to SOUND mode.
There are three sound modes to choose from:
• Standard: Suitable for watching movies, news, drama and so on.
• Music: Suitable for watching music programs.
• Sports: Suitable for watching sports games.
PICTURE MODE, SOUND MODE

19
TROUBLESHOOTING
TROUBLESHOOTING
• Check the signal strength in “Signal Information” menu item (refer to page 16), if this menu item is grey, it means
no signal was detected.
• Try to change the aerial/dish position/height, until you get the signal strength information in the above step and
until it shows a good signal level.
• Try to check the aerial/dish cable connection on both sides.
• If that does not work, report to Customer Care.
If screen shows “NO SIGNAL”
If screen shows “DISABLED”
• Check the connection between TV and the battery control unit (most of the time, it is caused by a loose connection).
• If that does not work, report to Customer Care.
Disabled