Sun Tastic PH08 series Parts list manual

1
Flame Heater – PH08 SERIES
ITEM # 126
ASSEMBLY AND OPERATION INSTRUCTIONS
DO NOT USE THE HEATER WHEN IT IS RAINING AND DO NOT LET ANY LIQUID
COME INTO CONTACT WITH THE GLASS TUBE WHEN THE HEATER IS IN USE.
FOR OUTDOOR USE ONLY
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
Read these instructions before using this appliance.The
appliance must be installed in accordance with these
instructions and local regulations. The use of this
appliance in enclosed areas can be dangerous and is
PROHIBITED.
• Perform leak test after each changing of LPG cylinder.
• Never check for leaks with a match or open flame.
•Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance.
IF YOU SMELL GAS
• Close the valve of the gas cylinder or regulator.
• Extinguish all open flames; do not operate any
electrical appliances.
• Check for leaks as detailed in these instructions.
•If odor persists, contact your dealer or gas supplier
***IMPORTANT NOTICE***
- Do NOT return to place of purchase-
For customer service and warranty issues
contact our Customer Service Center at:
0808 178 1018 OR
Email: [email protected]
Customer Service Hours: Mon. – Fri. 9:00 am – 5:00 pm, GMT
immediately!

2
PRECAUTIONS
· Installation and servicing should only be performed by a qualified person.
· Do not use the heater in an explosive atmosphere.
· Before each use, check the gas hose.
· Disconnect LPG cylinder before moving the heater.
· Do not attempt to alter any parts of the heater.
(Example: Using the heater without reflector or mesh protection guards.)
· The appliance shall not be used in basements or below ground level.
· The appliance must always be placed on a solid and level surface.
· Never replace or substitute the regulator. Use only the one that is suitable for the appliance category and
normal pressure of gas.
· Do not clean the heater with cleaners that are combustible or corrosive.
· Do not paint mesh protection guards, control box or reflector.
· The LPG gas cylinder valve should be turned off when the heater is not in use.
· Do not not use the heater when it is raining, and do not let any liquid splash on the glass tube when
the heater is working.
· Keep children away from the heater. Always be careful not to knock down the heater as this
will break the glass tube and may cause injury.
· Do not move the appliance when in operation.
· After a long break of operation, the gas parts in the control box of the heater and the gas hose should
be inspected for spiders, spider webs or other insects.
· Check the heater immediately if any of the following exists:
1. There is smell of gas.
2. The heater is not effectively producing heat.
3. The burner makes a popping noise during use (a slight popping noise is normal when the
burner is extinguished after use).
· If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas
supplier immediately.
· The gas hose and regulator assembly must be stored in a safe place to avoid any accidental
damage.
· Children and adults should be aware of the high surface temperature hazard, and should keep a
safe distance away to avoid clothes burning or igniting.
· Young children should be carefully supervised when they are in the working area of the heater.
· Clothing or other flammable material should not be hung from the heater, or placed on or near
the heater.
· Do not obstruct the flow of combustion products.
· Keep the ventilation opening of the cylinder enclosure free and clear of debris.
· Do not obstruct the ventilation holes of the cylinder housing.
· Shut off the valve of gas cylinder or the regulator before moving the appliance.
· The tubing or the flexible hose must be changed within the prescribed intervals.
· Use only the type of gas and the type of cylinder specified by the manufacturer.
· In case of violent wind particular attention must be taken against tilting of the appliance.

APPLIANCE STAND AND LOACTION
- The appliance is for outdoor use only. Do not use
it indoors or in an enclosed area.
- Always maintain proper clearance from combustible
materials ( i.e. top 800mm and sides 650mm minium. )
LEAK TEST
Gas connections on the appliance are leak tested at the factory prior to shipment. Possible
mishandling of the appliance during the shipment might contribute to product integrity as a whole.
A complete gas leak test must be performed again at the installation site. Please follow the
procedure below for leak test.
- Make a soapy solution of one part liquid detergent and one part water. The soapy solution can be
applied with spray bottle, brush or rag. Soap bubbles will appear where a leak is present.
- Make sure the control knob is in the “OFF” position (full disk = ●) on the control panel.
- Turn on the gas supply and check for bubbles from the hoses and connections. Presence of
bubbles means that a leak is present.
- If a leak is present, turn OFF the gas supply immediately, tighten any leaking fitting carefully,
turn gas back on and re-check for a leak.
- Never leak test while smoking or with an open flame.
INSTALLATION
Important safety requirements:
THIS APPLIANCE IS FOR OUTDOOR USE ONLY
1. This appliance shall not be installed or used indoors, in buildings, garages or any other
enclosed area.
2. DO NOT place articles on or against this appliance.
3. DO NOT use or store flammable materials near this appliance.
4. DO NOT operate this appliance unless it is fully assembled with reflector and protection mesh
guards in place.
5. Installation and repair should be done by a qualified service person. The appliance must be
inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners and
circulating air passages of the heater and burner be kept clean.
6. For use outdoors ONLY or in amply ventilated area. An amply ventilated area must have a minimum
of 25% of the surface area open. The surface area is the sum of the sum of the walls surface as
per below diagram.
3

4
PARTS LIST-1
Part NO. Part Name QTY Picture Remarks
Middle Plate 1
2 Control Box 1 Preassembled in
the Middle plate
3 Bottom Plate 1
4 Lower
Support
4
5 Upper support 4
6 Upper Plate 1
7 Plate cover 1 Preassembled in
the Middle plate
8 Glass tube 1
9 Damper 1 Preassembled in
upper plate
10 Reflector 1
1

5
PARTS LIST-2
Part NO. Part Name QTY Picture Remarks
11 Lower protection
guard
4
12 Connector 1
14 Fixing
bracket
4
15 Side panel 3
16 Front panel 1
17 Screw M3/16’’ 66 All preassembled in
relative parts
18 Handle 1
19 Chain 1
20 AA battery 1 Optional part
21 Wheels 2
22 Rubber ring 1

6
HEATER ASSEMBLY
Tools Required:
1 Phillips head screwdriver, 1 adjustable spanner
2. Take the control box(2) and the plate
cover(7) off the middle plate(1) by
unscrewing the screws(17)
4. Connect 4 upper supports (5) to the
lower supports (4) with screws(17),
then fix the upper plate(6) to 4 upper
supports(5) with screws(17).
1. Attach wheel (21) assembly to
bottom plate (3).
3. Connect and fix the 4 lower
supports(4) to bottom plate(3) and
middle plate(1) with screws(17)

7
6. Install a AA battery(20) into the
control box, then attach the control
box(2) underneath the middle plate(1)
with screws (17)
8. Attach the reflector (10) on the damper
(9) with screws(17).
5. Fix the plate cover(7) onto the
middle plate(1) with screws(17).
7. Carefully put the glass tube(8) up
through the center hole in the upper
plate(6)．Make sure the rubber ring is
attached on the lower end of the glass
tube(8). Move and sit the glass tube(8)
through the hole of the plate cover(7)
on the middle plate(1). Check and
ensure that the glass tube(8) covers the
center hole of the middle plate(1).

8
10.
11.
Completed
9. Hang the protection guards (11) onto
the frame by putting the hooks into the
holes of the frame. Affix the guards by
attaching the fixing brackets(14).
Screw the handle(18) onto the front panel(16). Attach the
connector(12) on the back of front panel with 2pcs
M4X8 bolts. Hook the chain(19) to the hole in control box,
then close the panel to the middle plate (panel is attracted by
magnets.)
Tips: The chain can hold the panel while operating the
controls.
Fix 3 side panels (15) with screws (17).
Note: Do not cover the side where the
control knob is located.

9
OPERATION
fi
OFF
LIGHT
LOW
HIGH

10

11

12