sunjoe SWJ806E User manual

© 2020 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe®, LLC
R
OPERATOR’S MANUAL
Model SWJ806E Form No. SJ-SWJ806E-880E-MR7
ELECTRIC POLE + CHAIN SAW
8-INCH | 8-AMP
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, re
and/or serious injury. Save all warnings and instructions for
future reference.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
General Power Tool Safety
Warnings
mWARNING! When using electric yard tools, basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury, including the following:
Work Area Safety
1. Keep work area clean and well lit – Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases
or dust – Power tools create sparks which may ignite the
dust or fumes.
3. Keep children and bystanders away while operating a
power tool – Distractions can cause you to lose control.
Electric Safety
1. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators – There is an increased risk of electric shock
if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions
– Water entering a power tool will increase the risk of
electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the inuence
of drugs, alcohol or medication – A moment of
inattention while operating power tools may result in
serious personal injury.
2. Use personal protective equipment. Always wear
eye protection – Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is
in the o-position before connecting battery packs,
picking up or carrying the tool – Carrying power tools
with your nger on the switch or energising power tools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on – A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at
all times – This enables better control of the power tool in
unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts – Loose clothes, jewellery or long hair
can be caught in moving parts.
7. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used – Use of dust collection
can reduce dust-related hazards.

2
Power Tool Use and Care
1. Do not force the power tool. Use the correct power
tool for your application – The correct power tool will
do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not turn
it on and o – Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
3. Disconnect the battery packs from the power
tool before making any adjustments, changing
accessories, or storing power tools – Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
4. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool – Power
tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may aect the power tool’s
operation. If damaged, have the power tool repaired
before use – Many accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and clean – Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
7. Use the power tool, accessories etc. in accordance
with these instructions, taking into account the
working conditions and the work to be performed –
Use of the power tool for operations dierent from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualied repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
Chain Saw Safety Warnings
• Keep all parts of the body away from the saw chain
when the chain saw is operating. Before you start the
chain saw, make sure the saw chain is not contacting
anything. A moment of inattention while operating the
chain saw may cause entanglement of your clothing or
body with the saw chain.
• Always hold the chain saw with your right hand on
the rear handle and your left hand on the front handle.
Holding the chain saw with a reversed hand conguration
increases the risk of personal injury and should never be
done.
• Hold the power tool by insulated gripping surfaces
only, because the saw chain may contact hidden
wiring. Saw chains contacting a "live" wire may make
exposed metal part of the power tool "live" and give the
operator a electric shock.
• Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet is
recommended. Adequate protective clothing will reduce
personal injury by ying debris or accidental contact with
the saw chain.
• Do not operate the chain saw in a tree. Operation of a
chain saw while up in a tree may result in personal injury.
• Always keep proper footing and operate the chain
saw only when standing on a xed, secured and level
surface. Slippery or unstable surfaces such as ladders
may cause a loss of balance or control of the chain saw.
• When cutting a limb that is under tension, be cautious
of spring back. When the tension in the wood bers is
released, the spring-loaded limb may strike the operator
and/or throw the chain saw out of control.
• Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you o balance.
• Carry the chain saw by the front handle with the
chain saw switched o and away from your body.
When transporting or storing the chain saw, always
t the guide bar cover. Proper handling of the chain saw
will reduce the likelihood of accidental contact with the
moving saw chain.
• Follow instructions for lubricating, chain tensioning
and changing accessories. An improperly tensioned or
poorly lubricated chain may either break or increase the
chance for kickback.
• Keep handles dry, clean and free from oil and grease.
Greasy, oily handles are slippery and can cause loss
of control.
• Cut wood only. Do not use the chain saw for any other
purpose. For example, do not use the chain saw to cut
plastic, masonry or non-wood building materials. Use
of the chain saw for operations dierent than intended
could result in a hazardous situation.
Causes and operator prevention of
kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse
reaction, kicking the guide bar up and back towards the
operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the
saw which could result in serious personal injury. Do not rely
exclusively upon the safety devices built into your saw. As a
chain saw user, you should take several steps to keep your
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:

3
• Maintain a rm grip (right hand on the rear handle and
left hand on the front handle with thumbs and ngers
encircling the respective handles) and position your
body and arms to allow you to resist kickback forces.
Kickback forces can be controlled by the operator if
proper precautions are taken. Do not let go of the
chain saw.
• Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the unit in unexpected situations.
• Only use replacement bars and chains specied by the
manufacturer. Incorrect replacement of bars and chains
may cause chain breakage and/or kickback.
• Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain. Decreasing
the depth gauge height can lead to increased kickback.
Specic Safety Rules
mWARNING! SHOCK HAZARD! – To protect yourself
from electrocution, do not operate the electric pole + chain
saw within 50 ft of overhead wires. Failure to follow this
instruction could result in severe personal injury.
Operating Tips for Pole Chain Saws
• Note the extension cord's location relative to the tool.
While operating the pole chain saw, be careful not to trip
over the cord.
• Keep the cord away from the chain and the operator at
all times.
• Keep children, animals, and bystanders a safe distance
away from the pole chain saw and extension cord.
• Only the pole chain saw operator should be in the
work area.
• Do not use the pole chain saw to cut down trees.
• Always use two hands when operating the pole chain saw.
Grip the pole chain saw securely with one hand on the
trigger and the other hand on the pole.
• Before starting the pole chain saw, make sure that the saw
chain is not in contact with any object.
• Do not allow the pole chain saw to make contact with
grounded objects such as pipes, fences, and metal posts.
• Do not force the pole chain saw while cutting. Apply light
pressure. It will perform more eectively and safely if it is
used at the rate for which it was designed.
• Use extreme caution when cutting a limb that is under
tension. When wood tension is released, the limb could
spring back and strike the operator, causing severe injury
or death.
• Do not carry a plugged-in unit. Carry the pole chain saw
from one place to another with the unit unplugged. During
transport, hold the pole at its balance point (close to the
saw end), with the guide bar and chain facing to the rear.
When transporting or storing the pole chain saw, always t
the guide bar cover.
• Do not cut small brush and saplings with the pole chain
saw. Small branches may catch in the chain and be
whipped towards the operator, which could pull the
operator o balance.
Electrical Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
the electric pole + chain saw. Receptacles are available
having built-in GFCI protection and may be used for this
measure of safety.
2. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
3. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
Use this appliance only with a polarized UL-, CSA-, or
ETL-rated extension cord for outdoor, all-weather use.
The appliance plug will t into a polarized extension
cord only one way.
If the appliance plug does not t fully into the extension
cord, reverse the plug. If the plug still does not t, obtain
a correct polarized extension cord. A polarized extension
cord will require the use of a polarized wall outlet. The
extension cord plug will t into the polarized wall outlet
only one way. If the plug does not t fully into the wall
outlet, reverse the plug. If the plug still does not t,
contact a qualied electrician to install the proper wall
outlet. Do not modify the appliance plug, extension cord
receptacle, or extension cord plug in any way.
mWARNING! m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric pole + chain saw
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA-, or ETL-rated extension cord
for outdoor, all-weather use.
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
16
+50 ft - 100 ft
(+15 m - 30 m)
14

4
4. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
5. Do not abuse the cord. Never pull the electric pole + chain
saw by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
Kickback
mWARNING! Kickback may occur when the nose or tip of
the guide bar touches an object, or when the wood closes in
and pinches the saw chain in the cut.
AVOID CONTACTING THE GUIDE BAR TIP WITH ANY
OBJECT. In some cases, when the tip makes contact with an
object, it may cause a fast reverse reaction, kicking the guide
bar up and back towards the operator. Pinching the saw chain
along the top of the guide bar may also push the guide bar
rapidly back towards the operator. Either of these reactions
may cause you to lose control of the saw, which could result in
serious personal injury.
• When using as a pole chain saw, always use two hands
when operating the pole chain saw, one hand gripping the
trigger and the other hand gripping the pole. Use a rm
grip. Thumbs and ngers must wrap around the trigger
and the pole. When using as a chain saw, maintain a
rm grip (right hand on the rear handle and left hand on
the front handle with thumbs and ngers encircling the
respective handles) and position your body and arms to
allow you to resist kickback forces. Kickback forces can
be controlled by the operator if proper precautions are
taken. Do not let go of the chain saw.
• Keep all guards in place on the machine. Make sure they
are in proper working order.
• Do not overreach. Do not extend arms above shoulder
height when using as a pole chain saw or cut above
shoulder height when using as a chain saw. This helps
prevent unintended tip contact and enables better control
of the unit in unexpected situations.
• Keep solid footing and balance at all times.
• Never try cutting through two branches at the same time.
Only cut one at a time.
• Do not bury the guide bar nose or try to cut by boring the
guide bar nose into the wood.
• Watch for shifting of wood or other forces that may pinch
the chain.
• Use extreme caution when re-entering a previous cut.
• Use the low-kickback chain and guide bar supplied with
this electric pole + chain saw. Only use genuine
Snow Joe®+ Sun Joe®replacement parts designed
specically for use with this electric pole + chain saw.
• Never use a dull or loose chain. Keep the chain sharp and
properly tensioned.
• Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain. Decreasing the depth
gauge height can lead to increased kickback.
• Always observe the safety regulations and follow the
correct sawing techniques.
• Ensure safe carrying of the unit. Whenever the machine is
to be handled or transported, you must:
– Switch o the motor and wait for the chain to come to
a complete stop;
–Mount the guide bar cover;
–Hold the machine using the hand grips and
position the bar in the opposite direction to that used
during operation.
When using a vehicle to transport the machine, fasten the
tool rmly and position it so that it is not a danger to any
passengers.
• Before cutting, pruning, or delimbing for the rst time,
make sure:
– You have been specically trained to use this type
of equipment;
–You have carefully read the safety regulations and
user instructions contained in this manual;
– You practice rst on logs on the ground or attached
to trestles/saw horses, in order to get familiar with the
machine and the proper cutting techniques.
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
KICKBACK
DANGER ZONE

5
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
SAFETY ALERT – Indicates
a precaution, a warning or
a danger.
Wear personal protective
equipment, including
close-tting clothing.
The rotating part will continuously
run for several seconds after you
turn o the machine.
Double Insulation.
WARNING! Do not expose the unit
to rain or wet conditions.
CAUTION! Avoid contacting the
guide bar tip with any object. Tip
contact may cause the guide bar
to move suddenly upward and
backwards, which may cause
serious injury to the user.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
WARNING! SHOCK HAZARD
– Keep at least 50 ft (15 m)
away from power lines. Do not
overreach. Keep proper footing
and balance at all times.
Keep bystanders and children
a safe distance away.
SWITCH OFF! Remove plug from
outlet immediately if the cord is
damaged or cut.
Symbols SymbolsDescriptions Descriptions
DANGER! ROTATING BLADES
–Keep hands and feet away from
openings while the saw is running.
SWITCH OFF! Remove plug from
outlet before cleaning or conducting
maintenance checks.
Wear protective gloves and
non-slip footwear when using
the machine and handling debris.
50 ft
(15 m)

6
Technical Data
Rated Voltage........................................................120V ~ 60 Hz
Power .............................................................................. 8-amp
No Load Speed ............................................... 5500 ± 10% rpm
Bar/Chain Length ................................................ 8 in. (20.3 cm)
Cutting Thickness ...................................... Max: 7.5 in. (19 cm)
Recommended: 6.5 in. (16.5 cm)
Telescopic Shaft ................................................... 6.3 ft to 8.6 ft
(1.93 m to 2.63 m)
Overhead Reach ..................................................... 15 ft (4.6 m)
Oil Tank Capacity ................................................. 2  oz (60 ml)
Pole Chain Saw Weight...................................... 8.4 lbs (3.8 kg)
Chain Saw Weight .............................................. 5.5 lbs (2.5 kg)
1. 8 in. cutting chain
2. 8 in. guide bar
3. End cover nut
4. Front hand guard
5. Chain/sprocket end cover
6. Front hand grip
7. Removable cutting head
8. Cutting head lock
9. Cam-lock for telescopic pole
10. Oil tank cap
11. Oil level indicator window
12. Soft grip
13. Telescoping pole
14. Handle lock
15. Trigger switch
16. Removable handle
17. Appliance cord
18. Safety lock button
19. Cutting bar sheath
20. Hex key wrench/blade screwdriver
21. Extension cord restraint hook
Know Your Electric Pole + Chain Saw
Read the owner’s manual and safety instructions carefully before operating the electric pole + chain saw. Compare the illustration
below to the electric pole + chain saw in order to familiarize yourself with the location of the various controls and adjustments.
Save this manual for future reference.
R
R
1
2
4
6
3
5
7
Back of the cutting head
10
11
8
12
13
14
15
16
17
19
20
21
Back of the removable handle
18
9

7
Unpacking
Carton Contents
• Electric chain saw
• Telescoping pole
• 8 in. (20.3 cm) guide bar
• 8 in. (20.3 cm) cutting chain
• Hex key wrench/blade screwdriver
• Extension cord restraint hook
• Cutting bar sheath
• Manual with registration card
1. Carefully remove the electric pole + chain saw and check
to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric pole +
chain saw. The packaging is made of recyclable materials.
Properly dispose of these materials in accordance with
local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
Assembly
mWARNING! Always wear heavy-duty gloves when
handling the bar and chain. Mount the bar and chain very
carefully so as not to impair the safety and eciency of the
machine. If in doubt, contact an authorized Snow Joe®+
Sun Joe®dealer or call the Snow Joe®+ Sun Joe®customer
service center at 1-866-SNOWJOE (1-866-766-9563).
mWARNING! Unpacking and assembly should be
completed on a at and stable surface, with adequate space
for moving the machine and its packaging.
mDANGER! Never start the motor before installing the
guide bar, chain, and chain cover. Without all these parts in
place, the clutch can y o or explode, exposing the user to
potentially serious injuries.
mWARNING! To avoid serious personal injury, read and
understand all safety instructions provided.
mWARNING! Before performing any maintenance, make
sure the tool is unplugged from the power supply. Failure to
heed this warning could result in serious personal injury.
Installing/Replacing the
Guide Bar and Chain
Tools and supplies required:
• Dual-tipped hex key wrench/blade screwdriver (supplied)
• Heavy-duty work gloves
NOTE: When replacing the guide bar and chain, use only
identical replacement parts. Make sure the electric pole +
chain saw is disconnected from the power supply before
proceeding with installation.
1. Using the supplied hex key wrench, unscrew the end
cover nut and remove the chain/sprocket end cover
(Figs. 1 & 2).
2. Remove the cutting bar and chain from the mounting
surface (Fig. 3).
R
Fig. 1
End cover nut
Hex key wrench
R
Fig. 2
Chain/sprocket end
cover

8
3. Remove the old chain from the bar.
4. Lay out the new saw chain in a loop and straighten
any kinks. THE SHARP SIDE OF THE TEETH MUST
FACE AWAY FROM YOU IN THE DIRECTION OF THE
CHAIN ROTATION INDICATED ON THE GUIDE BAR
. If the teeth face backwards,
turn the loop over (Fig. 4).
5. Starting at the tip, mount the chain drive links into the
bar groove, leaving a loop at the back of the bar. The
chain will loosely t until it is placed on the sprocket
(Figs. 5 & 6).
NOTE: Make certain of the direction of the chain
.If the chain is mounted
backwards, the saw will vibrate abnormally and will not
cut.
6. Hold the chain in position on the bar and place the loop
around the sprocket. Fit the bar ush against the mounting
surface so that the bar studs are in the long slot of the bar
and the adjusting pin is in the chain tension pin hole
(Fig. 7).
7. Adjust the chain tension as needed by adjusting the
chain tensioner screw with the supplied at-tip blade
screwdriver. Make sure to align the chain tensioner screw
with the pin hole (Fig. 8).
8. Replace the chain/sprocket end cover. Tighten the end
cover nut, but leave the bar free to move for tension
adjustment.
R
Fig. 3
Cutting bar
Chain
Fig. 4
Chain rotation
Sharp cutting edge
Chain drive link
R
Fig. 5
R
Fig. 6
Loop
R
Fig. 7
Sprocket Bar studs
Chain tension pin hole
(with adjusting pin)
Fig. 8
Chain tensioner
Blade screwdriver

9
9. Remove all slack from the chain by turning the chain
tensioner screw clockwise until the chain seats snugly
against the bar with the drive links in the bar groove
(Fig. 9).
NOTE: The chain is correctly tensioned when there is no
sag on the underside of the guide bar; the chain is snug,
but can be rotated by hand without binding. For more
information on chain tensioning, see the maintenance
section beginning on pg. 15.
10. Tighten the end cover nut using the hex key wrench.
NOTE: If the chain is too tight, it will not rotate. Loosen the
end cover nut slightly and turn the chain tensioner 1/4 turn
counterclockwise. Lift the tip of the guide bar up and retighten
the end cover nut. Ensure that the chain can be rotated by
hand without binding.
NOTE: A new chain tends to stretch; check the chain tension
frequently, and adjust tension as required.
Pole Chain Saw Assembly
The machine comes in the chain saw mode. To convert it to a
pole chain saw, follow the instructions below.
1. Pull the handle lock toward you (Fig. 10).
2. While pulling the handle lock, use the other hand to grasp
the front hand grip and slide the removable cutting head
up to remove it (Fig. 11).
3. Connect the removable cutting head and the telescoping
pole by aligning their ends together and sliding the
removable cutting head downwards until it clicks into
position (Fig. 12).
4. Connect the removable handle and the telescoping
pole by aligning the their ends together and sliding the
removable handle upward until it clicks into position
(Fig. 13).
mWARNING! Always make sure that both the cutting
head lock and the handle lock are locked securely before
using the pole chain saw.
Fig. 9
Chain tensioner
Blade screwdriver
Fig. 10
Removable handle
Handle lock
Fig. 11
Removable cutting head
Front hand grip
Handle lock
R
Fig. 12
Removable cutting head
Telescoping
pole
Fig. 13
Telescoping pole
Removable handle

10
Chain Saw Assembly
1. To remove the cutting head from the telescoping pole,
PULL the cutting head lock back to release, and grasping
the front hand grip, SLIDE UP to remove the cutting head
(Fig. 14).
2. To remove the handle from the telescoping pole, pull the
handle lock back to release, and SLIDE DOWN to remove
the handle (Fig. 15).
3. Connect the cutting head with the removable handle by
aligning their ends together and slide the cutting head
downward until it clicks into position (Fig. 16).
mWARNING! Always make sure that the handle lock is
locked securely before using the chain saw.
Operation
Starting and Stopping
mCAUTION!
• Before starting the saw, remove the oil tank cap and add
bar & chain oil to the top of the oil level window
(Fig. 17). One minute of use will consume approximately
0.15  oz (4 ml) of oil. Rell when the oil level drops to
1/4 of a tank.
NOTE: Your electric pole + chain saw is equipped with an
automatic oil pump for bar and chain oiling. You must add
bar and chain oil or your electric pole + chain saw will not
function.
• Starting, stopping, and restarting an electric motor
repeatedly within a few seconds can generate a great deal
of heat and damage the motor. To protect the life of your
electric pole + chain saw, always wait at least ve seconds
after stopping before restarting the saw.
mWARNING! Be sure that the chain is not in contact with
any object when you start the motor.
mWARNING! Keep hands away from chain. Keep hands
on handles. Do not overreach.
A good, rm grip on the tool using both hands will help you
maintain control. When using as a pole chain saw, place one
hand on the soft grip and the other hand on the removable
handle with your thumbs and ngers encircling the pole and
handle. When using as a chain saw, maintain a rm grip by
placing your right hand on the rear handle and left hand on the
front handle with thumbs and ngers encircling the respective
handles. A rm grip combined with proper positioning of the
handle against your body will help you maintain control of the
saw. Do not let go of the saw while it is in operation.
R
Fig. 14
Removable cutting head
Cutting
head lock
Front hand grip
Fig. 15
Telescoping pole
Handle lock
Removable handle
R
Fig. 16
Removable
handle
Removable cutting head
R
Fig. 17
Oil level
window
Minimum level mark
Oil tank cap

11
mWARNING! Do not operate the electric pole + chain
saw in a tree, on a ladder, or on a scaold. Using the tool
under such circumstances is extremely dangerous.
mCAUTION! The chain will continue to run for several
seconds after turning o the tool.
Do not use the electric pole + chain saw under wet conditions.
Use extreme caution when cutting small brush, saplings,
or limbs under tension because slender and tense material
may catch the saw and be whipped toward you, pull you o
balance, or spring back.
Do not use the electric pole + chain saw to cut vines and/or
small underbrush.
mWARNING! Do not let familiarity with this type of tool
prevent you from taking all necessary precautions. Remember
that a careless fraction of a second is sucient to inict
serious injury.
mWARNING! Do not cut trees near electrical wires.
mWARNING! Failure to lubricate the chain will cause
damage to the bar and chain. Use only a good quality bar
and chain oil designed specically for use with chain saws.
One minute of use will consume approximately 0.15  oz.
(4 ml) of oil.
NOTE: It is normal for oil to seep from the saw when not in
use. To prevent seepage, empty the oil tank after each use.
When storing the unit for a long period of time (3 months or
longer), be sure the chain is lightly lubricated; this will prevent
rust on the chain and bar sprocket.
mWARNING! Be aware of the cord while operating the
saw. Keep the cord away from the chain. Be careful not to trip
over the extension cord.
1. Prior to each cutting session, run through the daily
checklist (see pg. 17).
2. Connect the electric pole + chain saw to a working 120 V
outlet using a heavy-duty outdoor extension power cord.
3. Push the appliance cord through the rst two slots of
the extension cord restraint hook, push the extension
cord through the remain two slots of the extension cord
restraint hook (Fig. 18). Then connect the cords.
4. To turn the tool ON, push and hold the safety lock button
(located on the removable handle) with your thumb and
then squeeze the trigger with your ngers. Once the tool is
running, you can release the safety lock button (Fig. 19).
5. To turn the tool OFF, release the trigger switch (Fig. 16).
NOTE: Do not press the trigger switch until you are ready
to make a cut.
Adjusting the Telescoping Pole
(Optional)
When being used as the pole chain saw, the machine is
equipped with a telescoping pole which provides up to
15.1 ft (4.6 m) of overhead reach. To adjust the telescoping
pole, follow the instructions below.
1. Disconnect the saw from the power supply.
2. Unclip the cam-lock to release the pole (Fig. 20).
Fig. 18 Extension cord
restraint hook
Appliance cord
Extension cord
Fig. 19 Safety lock
button
Trigger
switch
Fig. 20
Cam-lock

12
3. Extend the pole to the desired length (Fig. 21).
NOTE: Push poles toward each other to shorten the pole
or pull them away from each other to lengthen the pole.
Only extend the pole to the minimum length required to
reach the limb to be cut.
4. Lock the pole in position by closing the cam-lock (Fig. 22),
and ensure that the pole is secure. If the pole telescopes
when the cam-lock is closed, the nut may need tightening.
mWARNING! Failure to lock the telescopic pole cam-lock
as directed could result in personal injury.
Tightening the Bolt (Optional)
The retaining bolt may need tightening to secure the
telescoping pole in place.
To tighten the bolt, unclip the cam-lock. Using the hex key
wrench, tighten the cam-lock nut, then close the cam-lock.
Ensure that the pole is secure. The wrench may be required
to loosen the cam-lock nut if you need to adjust the pole to a
dierent height (Fig. 23).
Cutting Tips for Pole Chain
Saw
Proper Cutting Stance
• Balance your weight with both feet on solid ground.
• Your body should always be to the left of the chain line.
• The most typical cutting application is to position the
unit at an angle of 60° or less depending on the specic
situation (Fig. 24). As the angle of the pole chain saw shaft
to the ground increases, the diculty of making the rst
cut (from the underside of limb) increases.
Fig. 21
Telescoping pole
Fig. 22
Cam-lock
Fig. 23
Hex key wrench
Cam-lock nut
R
Fig. 24
60º MAXIMUM

13
Basic Cutting Procedure
This unit is designed for trimming small branches and limbs up
to recommended 6.5 in. (16.5 cm), not to exceed a max cut of
7.5 in. (19 cm) in diameter depending on type of wood.
Practice cutting a few small limbs using the following
technique to get the “feel” of using the saw before you begin a
major sawing operation.
• Take the proper stance in front of the tree with the
saw OFF (Fig. 24).
• Squeeze the trigger and let the chain accelerate to full
speed before entering the cut.
• Keep the saw running the entire time you are cutting;
maintain a steady speed.
• Allow the chain to cut for you; exert only light downward
pressure. If you force the cut, damage to the bar, chain, or
unit can result.
• PUSH and PULL – This reaction force is always opposite
to the direction the chain is moving when it is in contact
with the wood. Thus, the operator must be ready to
control the PULL when cutting on the bottom edge of the
bar, and PUSH when cutting along the top edge.
• Do not put pressure on the saw at the end of the cut.
Pruning
Pruning is the process of trimming limbs from a live tree.
• Remove long branches in several stages.
• Cut lower branches rst to allow the top branches more
room to fall.
• When pruning trees, it is important not to make the
nishing cut next to the main limb or trunk until you have
cut o the farthest lying limb. This will reduce the weight
and prevent stripping the bark from the main member.
• Under cut the branch 1/3 through for your rst cut.
Your second cut should over cut to drop the branch o
(Fig. 25). Be prepared to balance the weight of the pole
chain saw when the limb falls.
• Now make your nishing cut from the topside of the
branch smoothly and neatly against the main member so
the bark will grow back to seal the wound.
• Release the trigger ON/OFF switch as soon as the cut is
completed. Failure to follow proper cutting procedures will
result in the bar and chain binding and becoming pinched
or trapped in the limb.
Limbing
Limbing is the process of removing branches from a fallen tree.
• You should cut limbs one at a time. Remove the cut limbs
from the work area often to help keep the work area clean
and safe.
• Cut branches under tension from the bottom up to avoid
binding the bar and chain.
• Keep the tree between you and the pole chain saw while
limbing. Cut from the side of the tree opposite the branch
you are cutting.
If the Saw Becomes Pinched or Trapped
1. Wait for the blade to stop, wait ve minutes for the saw to
cool, unplug the power cord, and wear gloves to protect
your hands from the chain teeth.
2. If you can reach the limb from the ground, lift the limb
while holding the saw. This should release the “pinch” and
free the saw.
3. If the saw is still trapped, call a professional for assistance.
Cutting Tips for Chain Saw
Proper Cutting Stance
• Weight should be balanced with both feet on solid
ground.
• Keep your left arm and elbow locked in a "straight arm"
position to withstand any kickback force (Fig. 26).
• Your body should always be to the left of the chain line.
Fig. 25
Load
Second Cut
First Cut
1/3 Diameter
Finishing Cut
Fig. 26
Chain line Straight arm

14
Basic Cutting Procedures
mWARNING! Do not cut limbs or trees that are larger
than the maximum cutting thickness.
• Practice cutting a few small logs using the following
techniques to get the feel of using the saw before you
begin a major sawing operation.
• Take the proper stance in front of the wood with the saw
turned o (Fig. 26).
• Squeeze the trigger and let the chain accelerate to full
speed before entering the cut.
• Hold the saw with both hands rmly. Always keep your
left hand on the front handle and your right hand on the
rear handle so that your body is to the left of the chain
line.
• Keep the unit running the entire time you are cutting,
maintaining a steady speed.
• Let the chain do the work; exert only light downward
pressure. If you force the cut, damage to the bar, chain,
or unit can result.
• Do not put the pressure on the saw at the end of the cut.
• Always cut with both feet on solid ground to prevent
falling.
• Do not cut above chest height since it is dicult to
control kickback forces with a saw held high.
Limbing
Limbing is the process in which branches are removed from a
fallen tree. When limbing, leave larger lower limbs to support
the log o the ground. Remove the small limbs in one cut as
illustrated (Fig. 27). Branches under tension should be cut from
the bottom up to avoid binding the chain saw.
mWARNING! Pay special attention to where the
branches are lying on the ground and recognize the following
risks:
1). the branches may be under tension; 2). the direction in
which the branch will fall may dier from that anticipated;
3). the tree may be unstable after the branch has been cut.
Bucking a Log
mWARNING! Do not buck logs that are larger than the
maximum cutting thickness.
Bucking is the process in which a log is cut into lengths. It is
important to make sure your footing is rm and your weight is
evenly distributed on both feet. When possible, the log should
be raised and supported by the use of limbs, logs, or chocks.
Follow these simple directions for easy cutting:
• When the log is supported along its entire length as
illustrated (Fig. 28A), cut from the top (overbuck).
• When the log is supported on one end (Fig. 28B), cut 1/3
the diameter from the underside (underbuck). Then make
the nishing cut by overbucking to meet the rst cut.
• When the log is supported on both ends (Fig. 28C), cut
1/3 the diameter from the top (overbuck). Then make the
nishing cut by underbucking the lower 2/3 to meet the
rst cut.
1
2
1
Fig. 27
1
Fig. 28A
1
2
Fig. 28B

15
• It is easier to saw a log using the spiked bumper
(Fig. 28D).
–Dig the spiked bumper into the log and use it as a
pivot. Cut with an arched motion to make the bar
penetrate the wood.
–Repeat several times if necessary, changing the point
where you plant the spiked bumper.
–When bucking on a slope, always stand on the uphill
side of the log. When cutting through the log,
maintain control by releasing the cutting pressure
near the end of the cut without relaxing your grip on
the chain saw handles. Do not let the chain contact
the ground.
After completing the cut, wait for the saw chain to stop before
you move the chain saw. Always stop the motor before moving
from tree to tree.
Maintenance
Please contact an authorized Snow Joe®+ Sun Joe®dealer
or call the Snow Joe®+ Sun Joe®customer service center
at 1-866-SNOWJOE (1-866-766-9563) for all maintenance
operations not foreseen in this manual. Any operation
performed in an unauthorized service center or by unqualied
personnel will completely invalidate the warranty.
mWARNING! For your safety and that of others:
• Correct maintenance is essential to maintain the original
eciency and safety of the machine over time.
• Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
• Never use the machine with worn or damaged parts.
Damaged parts are to be replaced and never repaired.
• Only use original Snow Joe®+ Sun Joe®replacement
parts. Parts that are not of the same quality can seriously
damage the equipment, compromise safety, and invalidate
the warranty.
mWARNING! Always unplug the power cord before
performing any adjustments, maintenance, or repairs to your
electric pole + chain saw.
• Use protective gloves when handling the bar and chain.
• Keep the bar encased in its sheath, except when working
directly on the bar or the chain.
• Never dispose of oils or other polluting materials in
unauthorized places.
Motor Cooling
To avoid overheating and damage to the motor, always keep
the cooling air vents clean and free of sawdust and debris.
Chain Tension
Check the chain tension before using the saw when the chain
is cold. The correct tension of a cold chain is when there is no
slack on the underside of the guide bar; the chain is snug, but
you can rotate it by hand without binding.
During normal saw operation, the temperature of the chain
will increase. The drive links of a correctly tensioned warm
chain will hang approximately 0.050 in. (1.25 mm) out of the
bar groove (Fig. 29). Be aware that a chain tensioned while
warm, may be too tight upon cooling. Check the “cold tension”
before next use. The chain must be re-tensioned whenever the
ats on the drive links hang out of the bar groove (Fig. 29).
1
2
Fig. 28C
Fig. 28D
Spiked bumper
Spiked bumper
Fig. 29 Properly Adjusted Warm Chain
Approximately 0.050 in. (1.25 mm)
Flats are
visible here
Flats are not
visible here
Chain Needs Tensioning

16
NOTE: A new chain tends to stretch. Check the chain tension
frequently and re-tension as needed.
Nuts and Screws
Periodically check that all the nuts and screws are tightened
securely. Check that the cam-lock that controls the telescoping
pole is intact and in proper working order.
Chain Sharpening
mWARNING! To ensure that the saw works safely and
eciently, it is essential that the cutting components are
well-sharpened. It is highly recommended to replace the
chain once it loses its ability to cut cleanly and safely.
It is possible, however, to sharpen the existing chain if the
sharpening is carefully performed. Any work on the chain
and bar requires specic experience and special tools. For
safety purposes, we recommend you contact an authorized
Snow Joe®+ Sun Joe®dealer or call the Snow Joe®+
Sun Joe®customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Sharpening is necessary when:
• The sawdust looks like dust;
• Cutting becomes more dicult;
• The cut is not straight;
• Vibrations increase.
An authorized service center will sharpen the chain using the
right tools to ensure minimum removal of material and even
sharpness on all the cutting edges.
If you sharpen the chain yourself, use special round-section
les with the right diameter depending on the type of chain
(see “Chain Maintenance Table” pg. 18). You need a certain
amount of skill and experience to avoid damaging the cutting
edges.
Sharpen the chain as follows (Fig. 30):
• Secure the bar rmly, with the chain mounted, in a
suitable vise.
• Tighten the chain if it is loose.
• Mount the le in the guide and then insert it in the tooth at
a constant angle from the cutting edge.
• Sharpen in a forward motion a few times and repeat this
on all the cutting edges facing the same way (right or left).
• To move the chain forward, use a screwdriver.
• Turn the bar over in the vise and repeat on all the other
cutting edges.
• Check that the depth limiter tooth does not stick out
farther than the inspection tool and le any projecting
parts with a at le, rounding o the edges (Fig. 30).
• After sharpening, remove all traces of ling and dust
and lubricate the chain in an oil bath. Replace the chain
whenever:
– The length of the cutting edges decreases to 5 mm
or less;
– There is too much play between the links and the rivets.
Guide Bar Maintenance
When the guide bar shows signs of wear, turn it over on the
saw to distribute the wear for maximum bar life. Feathering or
burring of the bar rails is a normal process of bar wear. You
should smooth such faults with a le as soon as they occur.
Replace a bar with any of the following faults:
• wear inside the bar rails permitting the chain to
lay over sideways
• bent guide bar
• cracked or broken rails
• spread rails
Turn the saw over, check the underside of the guide bar, and
make sure that the lubrication holes and chain groove are free
from impurities.
You can purchase replacement parts for your Sun Joe®
SWJ806E electric pole + chain saw by ordering online at
sunjoe.com or, to order by phone, contact Snow Joe®+
Sun Joe®customer service at 1-866-SNOWJOE
(1-866-766-9563).
Fig. 30
Inspection tool
Depth limiter tooth
Cutting edge
Depth
limiter
tooth

17
Chain Sprocket
Regularly check the condition of the sprocket and replace it
when wear exceeds 0.5 mm (Fig. 31).
Do not mount a new chain with a worn sprocket or vice-versa.
Troubleshooting
Troubleshooting Tips
Most diculties are easy to x. Consult the troubleshooting
table for common problems and their solutions. If you continue
to experience problems or need repairs beyond these minor
adjustments, please call 1-866-SNOWJOE (1-866-766-9563)
for assistance.
mWARNING! Always unplug the power cord before
performing any adjustments, maintenance, or repairs to your
electric pole + chain saw.
Troubleshooting Table
Daily Checklist, Cleaning
and Storage
Daily Checklist
To help maintain your electric pole + chain saw for optimum
performance, we recommend you complete this checklist prior
to each work session.
mWARNING! Do not plug in the power cord until you
have completed all of the daily checks.
• Inspect for any visible damage to the chain, guide bar, or
motor housing.
• Inspect the oil port and guide bar rails and clean them to
remove any debris.
• Check the chain tension.
• Check the chain teeth for sharpness.
• Check the bar and chain oil level; ll with only new chain
oil specically formulated for chain saws.
NOTE: If you notice anything unusual, such as a vibration or
or an odd sound, shut the saw OFF immediately. Remove the
power cord and check the saw for any damage.
If you cannot nd the cause of the problem or are uncertain
what to do, then have the saw inspected by an authorized
Snow Joe®+ Sun Joe®dealer or call the Snow Joe®+
Sun Joe®customer service center at 1-866-SNOWJOE
(1-866-766-9563) before using it.
mCAUTION!
• Remove the power cord and wait at least ve minutes for
the saw to cool before servicing or storing your unit.
• If you drop the saw, carefully inspect it for damage. If the
guide bar is bent, the housing is cracked, the handle is
broken, or if you see any other condition that may aect
the saw’s operation, DO NOT USE the tool. Instead, have
it serviced at an authorized Snow Joe®+ Sun Joe®
dealer or call the Snow Joe®+ Sun Joe®customer service
center at 1-866-SNOWJOE (1-866-766-9563).
Cleaning
Use only mild soap and a damp cloth to clean the electric pole
+ chain saw. Never let any liquid get inside the motor housing
and NEVER immerse any part of the saw housing in liquid.
Storage
• Ensure that the guide bar cover is in place when storing.
• Do not store the electric pole + chain saw near chemicals,
such as fertilizers or other harsh solvents. Do not expose
the plastic parts of the unit to brake uids, gasoline,
petroleum-based products, penetrating oils, or the like.
These products are often highly corrosive and may cause
permanent damage, weaken, or destroy the plastic parts
of your unit.
< 0.5 mm
Fig. 31
Problems Corrective Action
The saw
motor fails
to start
•Check that you installed the extension cord
properly into the saw power cord receptacle and
that you plugged the extension cord into a live
120 V outlet.
•Make sure that you fully depress and hold the
safety lock button before squeezing the ON/OFF
trigger switch.
•The chain is too tight; re-tension.
•The chain tension is too tight; re-tension.
• The chain oil tank is empty; rell.
•The lubrication holes are plugged; clean them out.
•The chain tension is too tight; re-tension.
•The guide bar or chain is damaged; inspect
and replace the damaged part.
The saw
runs, but
the chain
speed is
low
Bar and
chain
running
hot and
smoking
The saw
motor
runs, but
the chain
is not
turning

18
• When not in use, your machine should be stored indoors
in a dry and high or locked-up place, out of the reach of
children.
Support
If your Sun Joe®SWJ806E electric pole + chain saw requires
service or maintenance, please call 1-866-SNOWJOE
(1-866-766-9563) for assistance.
Model and Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Record the following numbers from the housing or handle of your
new product: Model #:
Serial #:
S W J 8 0 6 E
Chain Maintenance Table
33
3/8
inches mm
Drive Links Chain Pitch Chain Gauge File Diameter
inches mm inches mm
9.5 0.050 1.3 45/32