SUNMORY MF19306 User manual

User Manual
Shelf floor lamp with USB and outlet
6. Assembling
Assembling diagram is on the back, please read it carefully at first.
7. Usage
On/off：Pull the chain switch.
CCT：You can change the CCT every two pulls.
8. Warranty and Our mission
Light the world, Warm your heart, which is the goal that we have been
pursuing. We’d like to provide the best lamps and service to you. We provide
a 36-month warranty for you. If you have any questions or suggestions,
please contact us ( E-mail: [e-mail] ) soon, we would do our best to
solve the problem and improve ourselves. Wish you enjoy the lamp and our
service.
1. Introduction
Thank you for purchasing our solid wood shelf floor lamp. Please read the
following instructions carefully before assembly. If you have any question,
please contact us by E-Mail ( [e-mail] ) .
2. Product Features
1.DIY assembly, modern minimalist style, classic color scheme. The
versatile design brings not only a beautiful luminaire, but also convenient
storage options.
2.The multi-tiered shelves allow you to display vases, books, plants etc for
decoration.
3.Different light bulbs with E26 base can be applied to meet different
ambience needs.
4.The lamp is an upgraded version of 2021, updated from 1 outlet to 2
outlets.Wish you will enjoy it.
3. Parameter
4. Cautions
1.Please keep it in a dry environment and don’t touch the lamp with wet
hands.
2.For a longer service life, please do not use the lamp in hot or corrosive
surroundings.
3.Please make sure that the voltage is 100-120V, which is standard for US.
This product can only be used between 100-120V.
4.Unplug before cleaning.
5.Each shelf can take a maximum load of 10 Lb. Please make sure not to
put more than 10 Lb on each shelf.
6.If you have any question, please contact us by E-mail.
7.The total power of the 2 AC output ports is 1080W, please do not use
electrical appliances that exceed the power.
5. Package List
Brand SUNMORY
Model
Power For Bulb
Power For Outlet
Power For USB
Material
Socket Type
Switch
Recommended Bulb
Size For Shade
Size For Lamp
Bulb
Voltage
Power
Brightness
CCT
Life
MF19306
MAX 60W
MAX 1080W
5V 2A
Wood + Fabric
E26
Pull Switch
A19/ST64/ST58
10.23 x 10.23 x 14.56 inches
10.23 x 10.23 x 63 inches
100-120V
9W
800lm
3000K-5000K-4000K
30000h
a Top panel * 1 b Drawer panel * 1 c Middle panel * 1 d Bottom panel * 1
e Wire clamp * 6 f Screw 2 * 9
( 1 For spare)
g Screw 1 * 9
( 1 For spare)
h Lamp shade * 1
i Wooden pole * 12 j Screw 3 * 6
(2 For spare)
k lamp nut * 1 +
l Lamp holder * 1
m USB and outlet box * 1
n Screwdriver * 1 o Hex wrench * 1 p EVA coshion * 1 q Top iron frame * 1
r Down iron frame * 1 s Bulb * 1 t Dam-board *1+
v Drawer stuck * 1
u Drawer * 1
k
t
v
Lamp
l
Manufacturer: Dongguan Mingjian Lighting Technology Co., Ltd
Address: Room 201, Building No.18, Houjie Section, Houda Road, Houjie Town,
Dongguan City, China
Distributor: Shenzhen Yioumai Technology Co.,LTD
Address: 2/F,BLDG.9,Fu'an Phase II Gongyecheng NUM. EXT. Xintian Community, Fuhai
ST. Bao'an DIST., Shenzhen, China

Step 5: Tighten the wooden
poles and fix them on the middle
panel.
Step 8:Tighten the wooden poles
and fix them on the storage panel.
Step 9: Fix the top panel on
the poles firmly with the
screw 1( 4PCS ) via hex
wrench.
Step 16-17: Clip the wire into the wire clamps. Step 18: Tear off the sticky side of the lampshade
and install the bulb. Then install the drawer and drawer stuck.
Step 1: Use the hex wrench to fix
the bottom panel and the wooden
poles( 4PCS ) firmly with screw 1(4
PCS ). Note that the concave side
of the bottom panel is facing down.
Step 3-4: Put the middle panel on the
wooden poles through screws 2.
Step 10: Use the screwdriver to fix
USB and outlet box and dam-board to
the drawer panel with screw 3( 7PCS) .
Step 11-12: As shown in the picture, make the end cable
of the lamp holder, washer and wing nut pass through
the top panel. Fix the lamp holder on the top panel with
a wing nut, and then fix the wire with the USB and socket
box with the included nut.
Step 2: Stick the EVA cushion to the bottom of
the bottom panel. Rotate screw 2(4PCS) and
fix them to the top of the wooden poles.
Step 13: Stick the lampshade to
the iron frames. Note that the
concave side of the iron frame
face down.
Step 14: Fix the lampshade on the
lamp holder with the lamp nut.
Step 15: Clamp the wire clamps on
the lamp poles.
Step 7: Pass the drawer panel
through screws 2 and place it on
the wooden poles.
i
dg
o
g
g
g
01
f
p
f
f
f
02
c
03 04 05
ff
f
f
06
b
07 08
g
g
gg
09
m
n
j
10
11 12 h
q
r
13
16 17 18
k
14
e
15
Step 6: Rotate screw
2(4PCS) and fix them to the
top of the wooden poles.
Video Installation tutorial
http://service.sunmory.com