SUNTEC Klimatronic Progress 7.0 plus User manual

Progress plus
Instruction manual
GB

2
Figure 1 Figure 2
Figure 3 Figure 4
Figure 5 Figure 6 Figure 7
Figure 8 Figure 10
Please read this user’s manual carefully to ensure proper use, maintenance and installation.

3
SPECIFICATION
1. Do not use the unit on a socket under repairs or not installed properly.
2. Do not use the unit, follow these precautions:
A: Near to source of fire.
B: An area where oil is likely to splash.
C: An area exposed to direct sunlight.
D: An area where water is likely to splash.
E: Near a bath, a shower or a swimming pool.
3. Never insert your fingers, into the air outlet. Take special care to warn children of these dangers.
4. Keep the unit upward while transport and storage, for the compressor locates properly.
5. Before cleaning the air-conditioner, always turn off and disconnect the power supply.
6. When moving the air-conditioner, always turn off and disconnect the power supply, and move it slowly.
7. To avoid the possibility of fire disaster, the air-conditioner shall not be covered.
8. All the air-conditioner sockets must comply with the local electric safety requirements. If necessary, please check it for the requirements.
9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
10. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a
hazard.
Notes:
—If any parts damage, please contact the dealer or a designated repair shop;
—In case of any damage, please turn off the air switch, disconnect the power supply, and contact the dealer or a designated repair shop;
—In any case, the power cord shall be firmly grounded.
—To avoid the possibility of danger, if power cord is damaged, please turn off the air switch and disconnect the power supply. It must be replaced
from the dealer or a designated repair shop.
This air conditioner must be stored and transported upright, otherwise you may cause irreparable compressor damage. In case of doubt let
the unit rest for at least 24 hours before you start it.
Model No.
Klimatronic Progress 7.0 plus
Klimatronic Progress 9.0 plus
Klimatronic Progress 12.0 plus
Volt
230V~50Hz AC
230V~50Hz AC
230V~50Hz AC
Power consumption (EN14511)
780 W
980 W
1340 W
Cooling capacity
2050 W
2600 W
3500 W
Air Flow Volume
320 m³/h
320 m³/h
450 m³/h
Dehumification
1,0 Liter/h
1,2 Liter/h
1,5 Liter/h
Refrigerant
R410a
R410a
R410a
Measurements (BxHxT)
41,5 x 72,1 x 29,1 cm
41,5 x 72,1 x 29,1 cm
41,5 x 72,1 x 29,1 cm
Net Weight
23 kg
24 kg
25,5 kg

4
Name of Parts, Figure 1 Spare Parts, Figure 2
1. rear cover 5. caster 9. exhaust pipe
2. air inlet 6. power line 10. flat fixing clip
3. front cover 7. air inlet 11. square fixing clip
4. operation panel 8. air inlet
Appearance and Function of Control Panel, Figure 3
12. POWER Button 15. timer POWER button 18. water full indicator lamp
13. temperature –button 16. temperature + button 19. fan speed adjustment button
14. operation mode button 17. signal receiver window 20. LED Window
Operation Display, Figure 4
1. Auto Mode Icon
2. Fan Speed
3. Cooling Mode
4. Temp. and Timer Setting
5. Timer on
6. Temperature °C
7. Dry Mode Icon
Appearance and Function of Remote Controller, Figure 5
21. POWER Button; press this button will turn the machine on or off
22. Temperature setting button; this button is used to set the room temperature.
Each key press increases the room temperature about 1°C.
23. Speed Button; Press this button will choose high, middle or low ventilation speed.
24. Timer button; press to set the timer on or off
25. Temperature setting button; this button is used to set the room temperature.
Each key press reduces the room temperature about 1°C.
26. Mode Button; press this button will choose the function auto cooling, cooling, or dry.

5
Operation Introduction, Figure 6
Before starting operations in this section:
1. Find a place where there is power supply nearby.
2. As shown in the figure on the right, install the exhaust hose, and adjust the window position well.
3. Insert the power cord into an grounded AC230V/50Hz socket;
4. Press the POWER button to turn on the air-conditioner.
5. After switching on, or over, the ventilator operates, but the compressor starts later. Cooling effect may require a further 10 minutes.
Before using
Notice:
1. Operation temperature range:
Check up whether the exhaust hose has been mounted properly.
Cautions for cooling and dehumidifying operations:
-When using functions on cooling and dehumidifying, keep an interval of at least 3 minutes between turning on and turning off.
-Power supply meets the requirements.
-The socket is forAC use.
-Do not share one socket with other appliances.
-Power supply is AC230V，50Hz
2. Cooling operation
-Press the “Mode” button till the “Cool” icon (seeFigure4)appears.
-Press the “Temp+”or“ Temp-”buttontoselectadesiredroomtemperature.(16°C-31°C)
-Press the “Fan Speed” button to select wind speed.
-Aftersetting, thecurrentroom temperatureisshownon thedisplay.
3. AutoMode
- Press the “Mode” button till the “Auto” icon (seeFigure4)appears.
-Press the “Temp+”or“ Temp-”buttontoselectadesiredroomtemperature.
-After setting, the roomtemperatureis showninthedisplay.
-inAutomode,thefanspeedischangeable.
-Automodemeans,thattheunitwill turnoff, whenthedesiredroomtemperature is reachedandit willturnon,if the roomtemperature changes again.
-If the room temperature is equal to or above 18 ° C, the unit can cool in the automatic mode. At lower temperatures the device will protect the compressor by
automaticallyswitching intoventilationmode.
4. Dehumidifyingoperation
Press the “Mode” button till the “Dehumidify Indicator Lamp” (see Figure 4)blinks
-Theunitwillsetthetemperatureandthefanspeedbyitself.
5. Timeroperation
TimerONsettingcooling:
-Whentheair-conditioner is OFF, press the “Timer” button andselectadesiredONtimethroughthetemperatureandtimesettingbuttons.
-ONtimecanberegulatedatanytimein0-24hours.
-Press the “Timer” button to confirm your setting.
Timer OFF settingcooling:
-Whentheair-conditioner ON, press “Timer” button and select a desired OFF time through the temperature and time setting buttons.
-OFFtimecanbe regulated at anytimein 0-24hours.
-Press the “Timer” button to confirm your setting.

6
TimerOnsettingdehumidifying:
-Choosethedehumidifyingmodeas describedin4.
- Whentheair-conditionerOFF, press “Timer” button and select a desired ON timethrough the temperature and timesettingbuttons.
- Timecanberegulatedatanytimein0-24hours.
- Press the “Timer” button toconfirmyoursetting.
TimerOFFsetting dehumidifying:
-Whentheair-conditionerON,pressthe“Timer” button and select a desired OFF time through the temperature and time setting buttons.
-OFFtimecanbe regulated at anytimein 0-24hours.
- Press the “Timer” button to confirm your setting.
6. Drainage
-When you plan to leave this unit unused for a long time, please remove the rubber blockage from the drainage hole at the bottom of unit, and
connect a drain hose to the lower fixing clip. All the water in the water tank will drain outside.
-If water pump is damaged, continuous drainage can be used, and under this condition, the water pump is not activated. The unit can also
work well.
-If water pump is damaged, intermittent drainage can also be used. Under this condition, when the water full indicator lamp lights up, please
connect a drain hose to the lower fixing clip, then all the water in the water tank will drain outside. The unit can also work well.
Installation Explanations
-A removal air-conditioner shall be installed in the flat and empty place all around.
Don’t block the air outlet, and the required distance around should be at least 30cm.
-Theunitshouldnotbeinstalledindry-cleaner.
Introduction to Exhaust Hose Installation
A) Temporary installation
1. Twist both ends of the exhaust hose into the square fixing clip and the flat fixing clip.
2. Insert the square fixing clip into openings at back of the air conditioner.
Hook the left side of the adapter into the opening at the rear cover. Conduct the right side at the
rear cover and press it down until the Adapter engages.
3. Put the other end of the exhaust hose to the near windowsill.
4.
Maintenance Explanations
Declaration:
1) Before cleaning, be sure to disconnect the unit from any electric supply outlet;
2) Do not use gasoline or other chemicals to clean the unit;
3) Do not wash the unit directly;
4) If the conditioner is damaged, please contact the dealer or repair shop.
1. Air Filter
-If the air filter becomes clogged with dust/dirt, the air filter should be cleaned once every two weeks.
-Dismounting
Open the air inlet grille and take off air filter.
-Cleaning
Clean the air filter with neural detergent in lukewarm（40°C）and dry it up in the shade.
Mounting
Putting the air filter into the inlet grille, replace the components as they were.
-Clean the Air-conditioner Surface
First clean the surface with a neutral detergent and wet cloth, and then wipe it with a dry cloth.

7
Troubleshooting
Troubles
Possible Causes
Suggested Remedies
Unit does not start when pressing POWER
button
- Water full indicator lamp blinks, and water tank
is full.
Dump the water out of the water tank.
- Room temperature is higher than the setting
temperature. (Electric heating mode)
Reset the temperature
- Room temperature is lower than the setting
temperature. (Cooling mode)
Reset the temperature
Not cool enough
- The doors or windows are not closed.
Make sure all the windows and doors are
closed.
- There are heat sources inside the room.
Remove the heat sources if possible
- Exhaust air hose is not connected or blocked.
Connect or clean the exhaust air hose.
- Temperature setting is too high.
Reset the temperature
- Air inlet is blocked.
Clean the air inlet.
Noisy
- The ground is not level or not flat enough
Place the unit on a flat, level ground if possible
- The sound comes from the flowing of the
refrigerant inside the air conditioner
It is normal.
several operation icons will blink
- at a room temperature higher or equal 18°C, Auto mode and cooling mode will work together.
If the room temperature is equal to or above 18 ° C, the unit can cool in the automatic mode. At
lower temperatures the device will protect the compressor by automatically switching into ventilation
mode.
E0 Code
There is evidence that this error massage is
caused to a room temperature which is too high.
It can also caused by a temporary fault at the
rating between incoming- and outcoming
temperature.
Please turn off the unit and turn in on after 30
minutes. If this fault is everlasting, your
PROGRESS unit should be checked by a
professional.
E2 Code
Water tank full
Please empty the water tank.
Can I switch the PROGRESS unit on
immediately after unpacking it?
No.
The PROGRESS unit must be placed upright for
at least 24 hours after every transport.
Otherwise the compressor may be damaged
and there is no capacity.
When switching on the PROGRESS unit I sense
a smell. What should I do?
Production-related cause or incorrect storage of
unit at e.g. dusty areas.
Odour development can arise on first use and
after a longer period of non-use by storing in
unsuitable areas (e.g. dusty areas).
Run the unit for ½ a day. The smell will
disappear after a while. In the case of intensive
odour development, air the room.
Can I operate the PROGRESS unit WITHOUT
the extract air hose?
Yes, but only in dehumidification mode.
To achieve temperature adjustments, surplus
coldness must be discharged.
At which intervals should the activated carbon
filter of the PROGRESS unit be replaced?
To use the purpose of the filter fully, it should be
replaced every 6 months.

8
How can I increase the efficiency of the
PROGRESS unit?
External circumstances exist which may impact
the efficiency of the PROGRESS unit. Room
insulation, use of wall/window adapter, ratio of
window space (solar radiation), operation of
electrical units in the room (EDP), presence of
several persons in the room. You can increase
the efficiency of the PROGRESS unit
accordingly by adjusting such circumstances.
Compressor does not activate
Depending on ambient temperatures and
PROGRESS unit type it may take approx. 10
minutes after starting the compressor until the
cooling capacity is reached.
PROGRESS unit deactivates.
On reaching the set required temperature, the
PROGRESS unit switches off automatically.
Check manual setting of the required
temperature as well as the TIMER setting.
How is the m² or m³ data of the manufacturer
calculated
The m² or m³ data of the manufacturer for the
various PROGRESS units are average values
related to a room height of 2.5 metres. It must be
considered that such data can be clearly
underscored or exceeded under certain
circumstances. Circumstances which work
against efficiency of the PROGRESS units
include e.g. bad insulation of the building, large
window areas, south facing, attic apartment,
many additional heat sources, such as e.g.
number of persons, EDP, light, kitchen units,
washing units etc.
PROGRESS unit does not cool correctly
You achieve the most effective and economical
cooling comfort if you already cool the room to
be cooled when the room temperature is not yet
heated up. Air conditioners operate more
effectively if the temperature is to be maintained.
To drastically cool the air and inventory in a fully
heated room requires much more time and
energy.

10
EC-Declaration of Conformity
The unit complies with the essential health and safety requirements of the European Union. The EC declaration of conformity is the basis for the CE
marking of this unit.
ERP REGULATION
This high-quality single-channel portable air conditioning unit is in accordance with the rules and regulations of the European Union, in particular the
new ERP Regulation 626/2011 to a "local air conditioner."
REFRIGERANT
(CE) N 842/2006: This air conditioner contains the refrigerant R410A. The amount of refrigerant is less than 1kg, and is in a closed cooling circuit. The
coolant does have zero ozone depletion potential, but is a so-called greenhouse gases under the Kyoto Protocol and may thus contribute to global
warming, if it is released to the atmosphere. Therefore only trained technicians with refrigerant certificate make a filling or emptying. Suntec your air
conditioner does not have to use if used properly and undamaged coolant circuit can be refilled with refrigerant.
GWP: R410A(R32/125: 50:50): 1975
NOTE CONCERNING PROTECTION OF ENVIRONMENT
This product must not be disposed of via normal household waste after its service life, but must be taken to a collection station for the
recycling of electrical and electronic devices. The symbol on the product, the operating instructions or the packaging indicate such
disposal procedures. The materials are recycable inaccordance withtheir respective symbols. By means of re-use, material recycling or
any other form of recycling old appliances you are making an important contribution to the protection of our environment. Please ask
your local council where your nearest disposal station is located.