SUPERMICR R
CONTACT INFORMATION
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
PACKAGE CONTENTS
(Applies to single-pack only)
X9DRT-HF+
QUICK REFERENCE GUIDE REV. 1.00
ThismotherboardisdesignedtobeusedinanSMC-proprietary
server as part of an integrated system. No additional package
contents are included with the motherboard.
MNL-1334-QRG REV. 1.00
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
This motherboard supports up to 512 GB of 240-pin Registered (RDIMM)/Load
Reduced (LRDIMM) ECC or up to 128 GB of Unbuffered (UDIMM) ECC/Non-ECC
DDR3 800/1066/1333/1600 MHz 4-channel (per CPU) memory in 16 DIMM slots.
Note:For memory optimization,useonly DIMMmodulesthat havebeenvalidated bySupermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
FAN4 FA N3
I-SATA0
I-SATA1
JTPM1
X9DRT-HF+
JF2
JIPMB1
LE3
JPL1
JPB1
JWD1
JPG1
IPMI_LAN
P1 DIMMA1
P1 DIMMA2
P2 DIMMF2
P2 DIMME1
P1 DIMMD2
P1 DIMMD1
P2 DIMMH2
P2 DIMMH1
CPU1 Slot1 PCI-E 3.0 X8
P2 DIMMG1
P2 DIMMG2
P2 DIMMF1
P2 DIMME2
P1 DIMMB2
P1 DIMMB1
COM1
VGA
CPU1 Slot2 PCI-E 3.0 X8
LAN1
LAN2
USB2/3
P1 DIMMC1
P1 DIMMC2
BIOS
JBT1
Rev. 1.02
BMC
LAN CTRL
Battery
USB4
LE2
UIDSW1
LE1
USB1
LEM1
USB0
JPME1
JPME2
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CPU2
CPU1
Intel PCH
OPEN1st
Jumper Item # Description Default
JBT1 10 Clear CMOS See Chpt. 2 in User Manual
JPB1 20 BMC Enabled Pins 1-2 (Enabled)
JPG1 19 VGA Enabled Pins 1-2 (Enabled)
JPL1 21 GLAN1/GLAN2 Enable Pins 1-2 (Enabled)
JWD1 11 Watch Dog Pins 1-2 (Reset)
Connector Item # Description
COM1 26 Back Panel COM Port
JF2 16 SMC Proprietary Add-On Card for Power, FPControl & SATA Connections
JIPMB1 18 4-pin External BMC I2C Header (for and IPMI card)
JTPM1 23 TPM (Trusted Platform Module) Port 80 Header
LAN1 2 G-bit Ethernet Port 1
LAN2 3 G-bit Ethernet Port 2
(IPMI) LAN 1 IPMI Dedicated LAN
(I-)SATA 0 14 SATA 0 Connector
(I-)SATA 1 12 SATA 1 Connector
(CPU1) Slot1 13 PCI-E 3.0 x8 Slot for SMC-Proprietary Daughter (Add-On) Card
(CPU1) Slot2 15 PCI-E 3.0 x8 Slot for SMC-Proprietary Micro Low-Profile (LP) Card
UIDSW1 7 UID (Unit Idientifier) Switch
USB 0 5 Back Panel USB Port 0
USB 1 4 Back Panel USB Port 1
USB 2/3 17 Front Accessible USB Connections 2/3
USB 4 22 TypeA USB Connection (USB 4) for FrontAccess
VGA 6 Back Panel VGA Port
LED Item # Description Color/State Status
LED1 25 Onboard Standby PWR LED Green: Solid on Power On
LED2 8 UID LED Blue: On Unit Identified
LED3 24 HDD LED Green: On HDD/SATAActive
LEM1 9 BMC Heartbeat LED Green: Blinking BMC Normal
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
CPU Installation MicroLP Add-on Cards
Heat Sink Installation
Socket Keys
CPU Keys
1
5
1
9
1
15
1
14
1
10
1
4
1
8
1
13
1
3
1
7
1
12
1
17
1
18
1
19
1
20
1
2
1
6
1
11
1
16
1
21
1
26
1
22
1
23
1
24
1
25
1
1
Jumpers
Connectors
LED Indicators
Note: Item num-
bers are listed in
counterclockwise
order.
=mounting hole
1.
2.
OPEN1st
Screw #1
AOC-CIBF-m1 AOC-CGP-i2
AOC-CTG-i1S
Screw #2
Screw #4
Motherboard
Screw #3
Mounting Hole
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators. Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
Insert the desired number of DIMMs into the memory slots, starting with P1-DIMMA1.
For memory to work properly, follow the tables below for memory population order.
Refer to the motherboard layout (at left) for the location of the DIMM slots.
Processors and their Corresponding Memory Modules
CPU# Corresponding DIMM Modules
CPU 1 P1-
DIMMA1 P1-
DIMMB1 P1-
DIMMC1 P1-
DIMMD1 P1-
DIMMA2 P1-
DIMMB2 P1-
DIMMC2 P1-
DIMMD2
CPU2 P2-
DIMME1 P2-
DIMMF1 P2-
DIMMG1 P2-
DIMMH1 P2-
DIMME2 P2-
DIMMF2 P2-
DIMMG2 P2-
DIMMH2
Processor and Memory Module Population for Optimal Performance
Number of
CPUs+DIMMs CPU and Memory Population Configuration Table
(For memory to work properly, please follow the instructions below.)
1 CPU &
2 DIMMs CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
1 CPU &
5-8 DIMMs CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1-
DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs &
4 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1
2 CPUs &
10-16 DIMMs CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots
2 CPUs &
16 DIMMs CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/
P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-
DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Back Panel IO Connectors
Memory Support
DIMM Installation
A. IPMI LAN E. USB 1
B. GLAN1 F. VGA
C. GLAN2 G. UID
D. USB 0
A
B
C
This board features a MicroLP
slot (see #13 on layout) for
use with MicroLP add-on
cards, including the following:
