Suzuki SMD16 User manual

OPERATOR’S MANUAL
Multi-Function Display
Part No. 34916-98L20
Dec, 2018 Eng.
Printed in Japan
300 TAKATSUKA, MINAMI, HAMAMATSU, JAPAN
(Elemental Chlorine Free)
The paper used in this manual
is
elemental chlorine free.
A: DEC. 07, 2018
00019546410
Pub. No. OME-45060-A
(201812) SMD12/SMD16
34916-98L20
Multi-Function Display

i
IMPORTANT NOTICES
General
• This manual has been authored with simplified grammar, to meet the needs of international users.
• The operator of this equipment must read and follow the descriptions in this manual.
Wrong operation or maintenance can cancel the warranty or cause injury.
• Do not copy any part of this manual without written permission from SUZUKI.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and equipment specifications can change without notice.
• The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
• Save this manual for future reference.
• Any modification of the equipment (including software) by persons not authorized by SUZUKI will
cancel the warranty.
• The microSDXC logo is a trademark of the SD Card Association.
• The SD, SDHC and SDXC logos are trademarks of SD-3 LCC.
• Apple, App Store, iPhone, iPod, iPad are registered trademarks of Apple Inc, registered in the USA
and other countries.
• Android, Google and Google Play are registered trademarks of Google, Inc.
• FLIR is a registered trademark of FLIR Systems, Inc.
• Fusion-Link is a registered trademark of FUSION Electronics, Ltd.
• The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: SUZUKI MOTOR CORPORATION EUROPEAN LIAISON OFFICE -MARINE-
- Address: MINERVASTRAAT 16, 1930 ZAVENTEM, BELGIUM
• All brand and product names are trademarks, registered trademarks or service marks of their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal in
the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some SUZUKI products have a battery(ies). To see if your product has a battery, see the chapter on
Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery
before disposal to prevent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batteries must
not be discarded in standard trash, or at a trash site. Take the used bat-
teries to a battery collection site according to your national legislation and
the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd

ii
SAFETY INSTRUCTIONS
WARNING
CAUTION
Warning, Caution Prohibitive Action Mandatory Action
WARNING
CAUTION
The front panel of the display unit is made of glass. Handle it with care.
Injury can result if the glass breaks.
Read these safety instructions before you operate the equipment.
Indicates a condition that can cause death or serious injury
if not avoided.
Indicates a condition that can cause minor or moderate
injury if not avoided.
The radar antenna sends electromagnetic radio frequency (RF) energy. This
energy can be dangerous to you, especially your eyes. Do not look at the
radiator or near the antenna when the antenna is rotating.
The distances at which RF radiation levels of 100 W/m
2
and 10 W/m2exist are
shown in the table.
Check that no person is near the radar antenna before you turn on the radar.
Serious injury or death can occur if a person is hit by a rotating radar antenna.
Turn off the power immediately at the switchboard if water leaks into the
equipment or smoke or fire is coming from the equipment.
Failure to turn off the equipment can cause fire or electrical shock.
Do not open the equipment.
Only qualified persons can work inside the equipment.
DRS2D
DRS4A
DRS4D
DRS4DL
DRS6A
DRS12A
w/XN12A
DRS12A
w/XN13A
DRS25A
w/XN12A
DRS25A
w/XN13A
DRS4D-NXT
DRS6A X-Class
w/XN10A
DRS6A X-Class
w/XN12A
DRS6A X-Class
w/XN13A
DRS12A X-Class
w/XN12A
DRS12A X-Class
w/XN13A
DRS25A X-Class
w/XN12A
DRS25A X-Class
w/XN13A
Antenna
Model
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
Antenna
Model
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
N/A
N/A
0.4 ｍ
1.2 ｍ
0.1 m 1.4 ｍ
N/A 1.1 ｍ
DRS4DL+ N/A 0.9 ｍ
N/A 1.2 ｍ
0.2 m 2.4 ｍ
0.2 m 1.9 ｍ
0.5 m 5.3 ｍ
0.4 m 4.4 ｍ
N/A 0.7 ｍ
DRS6A-NXT N/A 0.7 ｍ
0.1 m 3 ｍ
N/A 2.2 ｍ
N/A 1.9 ｍ
0.3 m 3.1 ｍ
0.2 m 2.9 ｍ
0.8 m 7.7 ｍ
0.7 m 6.8 ｍ

SAFETY INSTRUCTIONS
iii
WARNING
Keep units other than the radar
antenna away from rain and
water.
Fire or electrical shock can occur if
water gets inside the equipment.
Do not disassemble or modify the
equipment.
Fire or electrical shock can occur if
the equipment is disassembled or
modified.
Do not operate the equipment with
wet hands.
Electrical shock can occur.
Do not depend on one navigation
device for the navigation of the
vessel.
Always check your position against
all available aids to navigation, for
the safety of vessel and crew.
A radar is an excellent
anti-collision aid, but remember
to keep watch for possible
collision conditions.
Always keep a watch while
underway.
Do not leave any objects near the
radar antenna.
Fire, electrical shock or injury can
result if something gets caught in the
radar antenna.
Use the correct fuse.
A wrong fuse can cause fire or
serious damage to the equipment.
Do not maneuver the vessel based
on the depth indication alone.
Grounding can occur.
CAUTION
The fish finder picture is not
refreshed when the picture
advance setting is “OFF”.
Do not use high-pressure cleaners
to clean this equipment.
This equipment has the waterproof
rating outlined in the specifications, at
the back of this manual. However, the
use of high-pressure cleaning
equipment can cause water ingress,
resulting in damage to, or failure of,
the equipment.

SAFETY INSTRUCTIONS
iv
The ARPA function is a valuable aid
to navigation. However, the naviga-
tor must check all aids available to
avoid collision.
- The ARPA automatically tracks an
automatically or manually acquired
radar target and calculates its course
and speed, indicating them with a
vector. Since the data generated by
the ARPA depends on the selected
radar targets, the radar must be
optimally tuned for use with the
ARPA, to ensure required targets will
not be lost or unnecessary targets,
like sea returns and noise, will not be
acquired and tracked.
- A target is not always a landmass,
reef, ship, but can also be returns
from the sea surface and from clutter.
As the level of clutter changes with
the environment, the operator must
correctly adjust the sea and rain
clutter controls and the gain control so
that the target echoes do not dis-
appear from the radar screen.
WARNING
The plotting accuracy and response of this
ARPA meets IMO standards. Tracking
accuracy is affected by the following:
• Tracking accuracy is affected by course
change. One to two minutes is required to
restore vectors to full accuracy after an
abrupt course change. (The actual amount
depends on gyrocompass specifications.)
•
The amount of tracking delay is inversely
proportional to the relative speed of the
target. Delay is approx. 15-30 seconds for
the higher relative speed; approx. 30-60
seconds for the lower relative speed. The
following factors can affect accuracy:
- Echo intensity
- Radar transmission pulse length
- Radar bearing error
- Gyrocompass error
- Course change (own ship and targets)
CAUTIO
CAUTION
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining
0.01% of the pixels may drop out or
blink, however this is not an indication of
malfunction.
About the TFT LCD
A safety label is attached to the display unit. Do
not remove the label. If the label is missing or
damaged, contact a SUZUKI agent or dealer
about replacement.
Name: Warning Label (1)
Type: 86-003-1011-3
Code No.: 100-236-233-10
Safety Labels
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.

v
TABLE OF CONTENTS
FOREWORD................................................................................................................. xiv
SYSTEM CONFIGURATION ........................................................................................ xvi
1. SYSTEM INTRODUCTION ....................................................................................1-1
1.1 Controls .....................................................................................................................1-2
1.2 Remote Control Units (option) ................................................................................... 1-5
1.2.1 Remote Control MCU-002 ............................................................................. 1-5
1.2.2 Remote Control Unit MCU-004...................................................................... 1-6
1.2.3 Control Unit MCU-005 ................................................................................... 1-7
1.2.4 Remote Control Unit group settings .............................................................. 1-9
1.3 How to Turn the Power On or Off ............................................................................ 1-11
1.4 How to Adjust the Brilliance of the Display and Power Switch and Hue.................. 1-12
1.5 Home Screen and Displays .................................................................................... 1-13
1.6 How to Select the Display........................................................................................ 1-14
1.6.1 How to select the display from the home screen......................................... 1-14
1.6.2 How to select the display from the quick page ............................................ 1-15
1.7 How to Edit the Display Icons.................................................................................. 1-16
1.7.1 How to add the new display icon ................................................................. 1-16
1.7.2 How to edit the display icon......................................................................... 1-17
1.8 Hidden Functions..................................................................................................... 1-18
1.9 Data Area ................................................................................................................ 1-20
1.9.1 How to change the order of the data ........................................................... 1-20
1.9.2 How to change the contents of the data box ............................................... 1-21
1.9.3 How to add data to the data area ................................................................ 1-21
1.9.4 How to delete the data box.......................................................................... 1-22
1.9.5 How to change the display method for data in the data box........................ 1-22
1.9.6 How to adjust the transparency of the data area......................................... 1-22
1.9.7 How to use the data box as the display for the FURUNO SC-33 ................ 1-23
1.10 MicroSD Cards ........................................................................................................ 1-24
1.11 Plotter Introduction .................................................................................................. 1-26
1.12 Radar Introduction ................................................................................................... 1-27
1.13 Sounder (Fish Finder) Introduction.......................................................................... 1-28
1.14 Settings Menu.......................................................................................................... 1-29
1.15 Function Gesture ..................................................................................................... 1-32
1.16 Language................................................................................................................. 1-33
1.17 Man Overboard (MOB) ............................................................................................ 1-34
1.18 Wireless LAN Settings............................................................................................. 1-35
1.18.1 How to connect the existing LAN................................................................. 1-35
1.18.2 How to create the local wireless network .................................................... 1-37
1.19 How to Create and Login to Your My TimeZero™Account ..................................... 1-38
2. ENGINE DISPLAY .................................................................................................2-1
2.1 Engine Display Overview........................................................................................... 2-1
2.2 Engine Display........................................................................................................... 2-1
2.2.1 Engine display examples............................................................................... 2-2
2.2.2 How to switch between Engine displays........................................................ 2-7
2.2.3 How to edit the Engine display ...................................................................... 2-8
2.2.4 Fuel management system ........................................................................... 2-12
2.2.5 SC-33 data display ...................................................................................... 2-13

TABLE OF CONTENTS
vi
2.3 Troll Mode ...............................................................................................................2-14
2.3.1 How to Use the Troll.....................................................................................2-14
2.3.2 How to display and operate from the slide-out menu...................................2-14
2.3.3 How to cancel the troll mode........................................................................2-15
2.4 QR Code .................................................................................................................. 2-16
2.4.1 How to create QR Code ...............................................................................2-16
2.4.2 How to view QR Code logs ..........................................................................2-17
2.4.3 Emailing the QR codes ................................................................................2-17
2.5 Reset Data ............................................................................................................... 2-18
2.6 SMD Modules...........................................................................................................2-18
2.7 Engine Alarms..........................................................................................................2-20
2.7.1 How to check the Alarm ...............................................................................2-20
2.7.2 List of Caution message...............................................................................2-21
2.8 CZone ......................................................................................................................2-22
2.8.1 How to use CZone .......................................................................................2-22
2.8.2 CZone control...............................................................................................2-23
2.8.3 CZone modes...............................................................................................2-25
2.8.4 CZone monitoring.........................................................................................2-28
3. PLOTTER .............................................................................................................. 3-1
3.1 Chart Type ................................................................................................................. 3-1
3.2 Display Range............................................................................................................3-2
3.3 Orientation Mode........................................................................................................3-3
3.4 How to Move the Chart ..............................................................................................3-3
3.5 The Boat Icon.............................................................................................................3-4
3.5.1 Description .....................................................................................................3-4
3.5.2 How to show or hide the COG vector, heading line .......................................3-4
3.5.3 COG vector length .........................................................................................3-5
3.5.4 Boat icon orientation ......................................................................................3-6
3.6 How to Information About a Chart Object, Chart........................................................3-6
3.6.1 Chart object information .................................................................................3-6
3.6.2 Chart information............................................................................................3-7
3.7 How to Find the Range and Bearing Between Two Locations...................................3-8
3.8 Multiple Plotter Displays.............................................................................................3-9
3.9 Cartographic Text and Objects on Vector Charts ....................................................3-10
3.9.1 Control visibility of text and object information in vector charts....................3-10
3.9.2 Control visibility of cartographic objects in S-52 charts................................3-11
3.10 Alarms ......................................................................................................................3-13
3.10.1 XTE alarm ....................................................................................................3-14
3.10.2 Depth alarm..................................................................................................3-14
3.10.3 SST alarm ....................................................................................................3-14
3.10.4 Speed alarm................................................................................................. 3-15
3.10.5 Anchor watch alarm ..................................................................................... 3-16
3.10.6 Low fuel alarm..............................................................................................3-16
3.10.7 Other Alarm menu items ..............................................................................3-16
3.10.8 Alarms list.....................................................................................................3-17
3.11 Track ........................................................................................................................3-17
3.11.1 How to start, stop recording the track ..........................................................3-17
3.11.2 How to show or hide the track display..........................................................3-17
3.11.3 Track recording interval................................................................................3-18
3.11.4 Track color ...................................................................................................3-19
3.11.5 Track thickness ............................................................................................3-21
3.11.6 How to create a route with past track...........................................................3-21
3.11.7 How to create a route with track currently being recorded (track back) .......3-22
3.11.8 How to delete tracks.....................................................................................3-23
3.11.9 How to find the number of track points used................................................3-23

TABLE OF CONTENTS
vii
3.12 Plotter Menu ............................................................................................................ 3-24
3.13 NAVpilot Series Auto Pilot....................................................................................... 3-25
3.13.1 How to enable use of the NAVpilot.............................................................. 3-25
3.13.2 How to show the NAVpilot control box in the data area .............................. 3-26
3.13.3 How to make an automated turn with the NAVpilot .................................... 3-26
3.13.4 How to change the NAVpilot settings .......................................................... 3-26
3.14 ActiveCaptain .......................................................................................................... 3-27
3.14.1 How to activate ActiveCaptain..................................................................... 3-27
3.14.2 How to hide or show the ActiveCaptain display........................................... 3-27
3.14.3 How to find a marina.................................................................................... 3-27
3.14.4 How to show or hide ActiveCaptain items ................................................... 3-28
3.14.5 How to update the ActiveCaptain database ................................................ 3-28
3.15 My Friends (Social Network) ................................................................................... 3-29
3.15.1 How to setup My Friends............................................................................. 3-29
3.15.2 How to show or hide the My Friends display ............................................... 3-29
4. 3D DISPLAY, OVERLAYS ....................................................................................4-1
4.1 3D Display ................................................................................................................. 4-1
4.1.1 How to activate the 3D display ...................................................................... 4-2
4.1.2 How to make the 3D view clearer.................................................................. 4-3
4.2 Overlays .................................................................................................................... 4-4
4.2.1 Depth shading overlay................................................................................... 4-4
4.2.2 Satellite photo overlay ................................................................................... 4-6
4.2.3 Radar overlay ................................................................................................ 4-6
4.2.4 Tide info overlay ............................................................................................ 4-8
4.2.5 Tidal current overlay .................................................................................... 4-10
5. POINTS, EVENT MARKS......................................................................................5-1
5.1 About Points, Event Marks ........................................................................................ 5-1
5.2 How to Enter a Point, Event Mark ............................................................................. 5-2
5.2.1 How to enter a point (plotter and radar displays only) ................................... 5-2
5.2.2 How to enter an event mark .......................................................................... 5-3
5.3 How to Display Point, Event Mark Information .......................................................... 5-4
5.4 Event Mark Comment................................................................................................ 5-5
5.5 Default Point, Event Mark Settings............................................................................ 5-5
5.5.1 Default point settings ..................................................................................... 5-5
5.5.2 Default event mark settings ........................................................................... 5-7
5.6 How to Find Number of Points Used ......................................................................... 5-7
5.7 Points List ..................................................................................................................5-8
5.7.1 How to show the points list ............................................................................ 5-8
5.7.2 How to sort the points list .............................................................................. 5-8
5.7.3 How to search the points list.......................................................................... 5-8
5.7.4 How to view and edit point details ................................................................. 5-9
5.7.5 How to edit a point on the screen ................................................................ 5-10
5.8 How to Move a Point ............................................................................................... 5-11
5.8.1 How to move a point on the screen ............................................................. 5-11
5.8.2 How to move a point from the points list...................................................... 5-12
5.9 How to Delete a Point.............................................................................................. 5-12
5.9.1 How to delete a point on the screen ............................................................ 5-12
5.9.2 How to delete a point from the points list..................................................... 5-12
5.9.3 How to delete all points ............................................................................... 5-12
5.10 How to Move a Point to the Screen Center ............................................................. 5-13
5.11 How to Show or Hide All Points or Points Names ................................................... 5-13
5.12 How to Set Point Density......................................................................................... 5-13

TABLE OF CONTENTS
viii
5.13 How to Go to a Point ................................................................................................5-14
5.13.1 How to go to an on-screen point ..................................................................5-14
5.13.2 How to go to a position selected on screen .................................................5-15
5.13.3 How to go to a point selected from the points list.........................................5-16
5.13.4 How to use the NAVpilot to steer to a point .................................................5-16
5.13.5 How to display the point information for the active goto point......................5-17
5.14 How to Restart or Cancel Navigation to a Point.......................................................5-17
5.14.1 How to restart navigation to a point..............................................................5-17
5.14.2 How to cancel navigation to a point .............................................................5-17
5.15 Boundary Lines ........................................................................................................5-18
5.15.1 How to show or hide boundary lines ............................................................5-18
5.15.2 How to find boundary lines data...................................................................5-18
5.15.3 How to find the number of boundary points used.........................................5-18
5.15.4 How to delete boundary lines.......................................................................5-19
5.15.5 How to edit boundary lines...........................................................................5-19
6. ROUTES................................................................................................................ 6-1
6.1 What is a Route?........................................................................................................6-1
6.2 How to Create a Route...............................................................................................6-2
6.2.1 How to create a new route from the plotter screen ........................................6-2
6.2.2 How to create a new route with points ...........................................................6-3
6.2.3 How to create a route from the points list.......................................................6-4
6.3 How to Edit a Route ...................................................................................................6-4
6.3.1 How to insert a route point on a route ............................................................6-4
6.3.2 How to move a route point on a route ............................................................6-4
6.3.3 How to delete a point (incl. route point) on a route ........................................6-5
6.3.4 How to remove a point from a route...............................................................6-5
6.3.5 How to extend a route ....................................................................................6-5
6.4 Routes List .................................................................................................................6-6
6.5 How to Find Number of Routes Created ....................................................................6-8
6.6 How to Find a Route on the Chart..............................................................................6-8
6.7 How to Delete a Route ...............................................................................................6-8
6.7.1 How to delete a route on the screen ..............................................................6-8
6.7.2 How to delete a route from the routes list ......................................................6-8
6.7.3 How to delete all routes..................................................................................6-8
6.8 How to Show or Hide All Routes ................................................................................6-9
6.9 How to Set Route Density ..........................................................................................6-9
6.10 How to Follow a Route .............................................................................................6-10
6.10.1 How to follow an on-screen route.................................................................6-10
6.10.2 How to follow a route selected from the routes list.......................................6-11
6.10.3 How to start navigation from a route point ...................................................6-11
6.10.4 How to show the detailed information about a route ....................................6-12
6.11 Operations When You Follow a Route.....................................................................6-12
6.11.1 How to restart navigation .............................................................................6-12
6.11.2 How to follow a route in the reverse direction ..............................................6-12
6.11.3 How to stop following a route .......................................................................6-12
6.11.4 How to skip a point on a route......................................................................6-12
6.11.5 Waypoint switching mode ............................................................................6-13
6.11.6 Route auto zoom.......................................................................................... 6-13
6.11.7 XTE lines......................................................................................................6-14
6.11.8 Waypoint arrival notification .........................................................................6-14
6.11.9 End of route notification ...............................................................................6-14
6.11.10How to change the autopilot’s operation once you arrive ............................6-14
6.11.11Steering a route with the NAVpilot ...............................................................6-15
6.12 Fuel Level Indicators ................................................................................................6-15
6.13 SAR Operations .......................................................................................................6-16

TABLE OF CONTENTS
ix
6.14 Laylines ................................................................................................................... 6-17
6.14.1 How to enable/disable the layline feature.................................................... 6-17
6.14.2 How to show layline data in the data area................................................... 6-17
6.14.3 How to change the polar wind file................................................................ 6-18
6.15 Routes Menu ........................................................................................................... 6-18
7. RADAR ..................................................................................................................7-1
7.1 How to Transmit, Set the Radar in Stand-by ............................................................. 7-1
7.2 Tuning........................................................................................................................ 7-1
7.3 How to Adjust the Gain.............................................................................................. 7-2
7.4 How to Reduce the Sea Clutter ................................................................................. 7-4
7.5 How to Reduce the Rain Clutter ................................................................................ 7-4
7.6 Range Scale .............................................................................................................. 7-5
7.7 Orientation Mode ....................................................................................................... 7-5
7.8 How to Measure the Range and Bearing from Your Ship to a Target ....................... 7-6
7.8.1 How to display the range rings ...................................................................... 7-6
7.8.2 How to set the number of the range rings to show ........................................ 7-7
7.8.3 How to select the range rings mode .............................................................. 7-7
7.8.4 How to measure the range and bearing to an object..................................... 7-8
7.8.5 How to measure the range with the VRM...................................................... 7-9
7.8.6 How to measure the bearing with the EBL .................................................. 7-11
7.8.7 How to select the EBL reference ................................................................. 7-12
7.9 How to Measure the Range and Bearing Between Two Targets ............................ 7-13
7.10 How to Off-center the Picture .................................................................................. 7-13
7.11 Heading Line ........................................................................................................... 7-14
7.12 How to Reduce Radar Interference......................................................................... 7-14
7.13 Echo Average .......................................................................................................... 7-15
7.14 Guard Zone ............................................................................................................. 7-15
7.14.1 How to set the guard zone........................................................................... 7-15
7.14.2 How to activate or deactivate the guard zone ............................................. 7-16
7.14.3 How to hide the guard zone......................................................................... 7-16
7.15 Watchman ............................................................................................................... 7-16
7.16 Echo Trail ................................................................................................................ 7-17
7.16.1 How to show, hide echo trails...................................................................... 7-17
7.16.2 How to clear echo trails ............................................................................... 7-17
7.16.3 How to select echo trail length..................................................................... 7-17
7.16.4 How to select the echo trail mode (reference)............................................. 7-18
7.16.5 How to select echo trail color....................................................................... 7-18
7.16.6 How to select echo trail shading.................................................................. 7-19
7.17 How to Show, Hide or Cancel an Active Route ....................................................... 7-19
7.18 How to Show or Hide the Own Ship Icon ................................................................ 7-19
7.19 Echo Color............................................................................................................... 7-20
7.20 Background Color.................................................................................................... 7-20
7.21 Dual-Range Display................................................................................................. 7-21
7.22 Bird Mode ................................................................................................................ 7-22
7.23 Target Analyzer ....................................................................................................... 7-23
7.23.1 How to activate or deactivate the target analyzer........................................ 7-25
7.23.2 How to emphasize rain clutter or target echoes .......................................... 7-25
7.24 RezBoost™.............................................................................................................. 7-25
7.25 Connecting With FURUNO FAR-2xx7/FAR-15xx Series Marine Radars ................ 7-26
7.26 Radar Menu............................................................................................................. 7-27
7.27 How to Interpret the Radar Display ......................................................................... 7-29
7.27.1 False echoes ............................................................................................... 7-29
7.27.2 Search and rescue transponder (SART) ..................................................... 7-31
7.27.3 RACON (Radar Beacon) ............................................................................. 7-31