Swiss Military SM34054 User manual

WWW.SWISSMILITARYTIME.CH
InstructIon manual
SM34054 Limited Edition
Calibre ETA E48.341
Thank you very much for buying a SWISS MILITARY BY CHRONO watch. Our watches
are made in Switzerland and bear the I «SWISS MADE» seal of approval. We guarantee
Swiss precision that serves tradition, innovation and competence. Your Limited Edition is
a sporting, multifunctional watch with innovative technology. Apart from showing the
time in an analogue form, it also has various extra digital displays.The following functions
can also be activated by simply pressing the pushers: weather, altimeter, chronograph,
alarm, timer, time zones and thermometer.
Important notice
Only authorised CHRONO AG service centres may be entrusted with any
service work.
Chrono AG
Service Center
Weissensteinstrasse 49
CH-4502 Solothurn
Switzerland
Weather
Changes in the weather are associated with changes in the atmospheric pressure. The
watch measures these changes in pressure and indicates weather trends using the hands.
Depending either on how the weather will develop, the hands point towards plus (good
weather) or minus (bad weather).The digital display also shows the absolute and relative
atmospheric pressure in hectopascal. More information can be found in section M.
Altimeter
The altimeter is an innovative function that shows the current height above sea level.The
altimeter should be recalibrated regularly to ensure a precise altitude measurement. Set
the altimeter to the effective height of a known point and repeat this procedure for new
values. Changes in the atmospheric pressure due to sudden changes in the weather may
affect the altimeter‘s display, even if the effective height has not changed. The accuracy
of the altimeter calls for an adjustment to the geographical location (hemisphere and
climate zone, section Q). More information can be found in section L.
Thermometer
When in the thermometer mode, the watch shows the ambient temperature. However, the
watch case is affected by your body temperature when the watch is worn and can lead
to inaccurate results. To ensure an optimum measurement, take the watch off your wrist
and wait for 15-30 minutes.
Contact with water
The watch is waterproof up to a pressure of 10 bar (100 m/330 ft), but is not suitable for
diving.The sensors do not work under water and there is a risk of water getting inside the
watch if you press the red pushers. Never press the push-pieces under water!

Pressure of
pushbutton C:
Decreases
continually
Pressure of
pushbutton A:
Increases
continually
Rapide correction
Long pressure of
pushbutton B:
(maintained when
buttons are being
pressed)
Activating background lighting
Pressure of
pushbutton C:
Decreases the
value gradually
Pressure of
pushbutton A:
Increases the
value gradually
Correction mode B
GENERAL OPERATION INFORMATION (continued)
B
GENERAL OPERATION INFORMATION
Pressure of
pushbutton B
(next index)
Navigating in the settings
Long pressure of
pushbutton A:
(LCD display
flashes)
Activating the correction mode
Pressure of
pushbutton C
(next sub-menu)
Navigating between sub-menus
Pressure of
pushbutton B:
- next menu
Double pressure:
- previous menu
Navigating between menus
Parking to the
nearest position:
09.15 h or 03.45 h
or
Pressure of
pushbutton B
(Parking hands
and activation
navigation)
Activating the navigation
End of energy
E . O . E .
End of life
E . O . L .
2 Times:
local + journey time
Thermometer
2 alarms
Timer
Chronometer
(ADD and SPLIT)
Date
Weather, ablosute
and realtive pressure
Altimèter
4275 m
Altitude difference
meter (option)
m
Digital display
Pushbutton C
Pushbutton B
Pushbutton A
Minute hand
Hour hand
Watch hands A
DISPLAY
633 893 - 11.08.2015 / ETA / 00
WWW.SWISSMILITARYTIME.CH
ETA E48.341
ETA E48.341

633 893 - 11.08.2015 / ETA / 00
: Settings
8.5
à
8.1
Selection
mode
„Options“
Sync
8.5
Selection
mode
„Sync“
Climate zone
8.4
Selection
mode
„Climate zone“
sleep
8.3
Selection
mode
„sleep“
beep
8.2
Selection
mode
„beep“
Units
8.1
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
Selection
mode
„Units“
Selection
mode
„Date“
Options
8
Selection
mode
„Options“
Temperature
7

+
Selection
mode
„Weather relative“
Weather
(absolute)
6.1

+
Selection
mode
„Weather absolute“
Selection
mode
„Temperature“
Weather
(relative)
6
Selection
mode
„Altitude“
Altitude diffe-
rence meter
(OPTION)
5.1
Selection
mode
„Altitude difference
meter“
(OPTION)
Selection
mode
„Weather
relative“
Altitude
5
m
4275 m
Selection
mode
„Alarme 1“
Alarme 2
4.1
Selection
mode
„Alarme 2“
Selection
mode
„Altitude“
Alarme 1
4
Selection
mode
„Alarme 1“
Timer
3
Selection
mode
„Timer“
Chrono
2
Selection
mode
„Date“
Time “T2”
1.2
Selection
mode
„Time T2“
Time “T1”
1.1
Selection
mode
„Time T1“
Selection
mode
„Chrono“
Date
1
C
NAVIGATION

633 893 - 11.08.2015 / ETA / 00
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
- 1 sec
Confirms recorded
data, quit the settings
menu.
(Display stops
flashing)
+ 1 sec
6
- 1 min
Selection
„second“
+ 1 min
5
- 1 h
Selection
„minute“
+ 1 h
4
Selection
mode
„Settings“
(Display flashes)
3
During the last
5 seconds, the
display „t1“
flashes and „beeps“.
RESET
STOP
2
START
1
I
TIMER
The split-time total is not reset so that two different times that are very close together can be measured.
5
Reset to zero
7
5
STOP TOTAL (Display Stop )
6
4
STOP Splitt (display Split )
5
Splitt
4
Run
3
Splitt
2
START
1
H
TIMING MODE (SPLITT)
SPLIT-TIME or INTERMEDIATE TIME function
Reset to zero
5
STOP Read
4
RUN
3
STOP Read
2
START
1
G
TIMING MODE (ADD)
ADD function
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
+ 1 day
Confirms recorded data,
quit the settings menu
+ 1 day
4
+ 1 month
Selection
„day“
+ 1 month
3
+ 1 year
Selection
„month“
+ 1 year
2
Display
flashes
1
Date
(mode 12h)
(MM.DD.YY)
Date
(mode 24h)
(DD.MM.YY)
F
CORRECTION THE DATE (perpetual calendar)
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
- 1 min
Quit mode
settings
+ 1 min
4
- 1 h
Selection
„minute“
+ 1 h
3
Long pressure of
pushbutton A:
start mode
settings
2
Pressure of
pushbutton A
(display flashes)
1
E
CORRECTION TIME “T2”
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
Quit mode settings
Seconds „00“ and
quit mode settings
Quit mode settings
5
- 1 min
Selection
„second“
+ 1 min
4
- 1 h
Selection
„minute“
+ 1 h
3
Long pressure of
pushbutton A:
start mode
settings
2
Pressure of
pushbutton A
(display flashes)
1
D
CORRECTION TIME “T1”

633 893 - 11.08.2015 / ETA / 00
Once EOE mode
has been reached
the watch must
reseted.
P
END OF ENERGY (EOE)
E . O . E .
every 4 seconds
O
END OF LIFE (EOL)
E . O . L .
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
Long pressure of
pushbutton C
RESET
Pressure of
pushbutton A
START/STOP
The small flashing R signals that the
altitude-difference measuring function is activated.
Back to display
Note: The information cycles for
the altitude-difference measuring
function are repeated 3 times.
7
Display:
Average vertical speed
during the descent over
the elapsed time
(303 ft/min)
6
Display:
Total altitude lost
over the elapsed
time
(26895 ft)
5
Display:
Average vertical speed
during the climb over
the elapsed time
(62 m/min)
4
Display:
Total altitude gained
over the elapsed
time
(+ 5206 m)
3
Selection display of
altitude diference
Display:
Elapsed time, rum time,
or stopped time
(3 days, 18 hours,
55 minutes)
2
Selection display of
altitude difference
meter
(display changes
every 3 seconds)
1
N
ALTITUDE DIFFERENCE METER (OPTIONAL)
m
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
 +
Confirms recorded
data, quit the
settings menu
3
 +
- 1 hPa
+ 1 hPa
2
 +
Selection
mode
„Settings“
1
M
WEATHER
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
Confirms recorded
data, quit the
settings menu
3
- 1 m
+ 1 m
2
Selection
mode
„Settings“
1
L
ALTIMETER
4275 m
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
Confirms recorded
data, quit the
settings menu
3
„Continuous pro-
cessing“ mode:
- 1. minutes
- 2. hours
Pushbutton A: +
Pushbutton C: -
(Display flashes)
4
Selection
mode
„Settings“
3
ALARM
OFF
2
ALARM
ON
1
K
ALARM 1 + 2

633 893 - 11.08.2015 / ETA / 00
Time-Out after
15 seconds:
Back to the mode
„Date“
(Display „analog/
digital“ in accordance
with the last choice).
The hour hand corrects
one step clockwise
Confirms the new
option and quits the
settings menu
The hour hand corrects
one step clockwise
The minute hand corrects
one step clockwise
Confirms and starts
synchronisation of
the hour hand
The minute hand corrects
one step clockwise
Selection
mode
„Options“
Sync
Changes
clima:
T, M, A, tr, P
Confirms the new
option and quits the
settings menu
Changes
hemisphere:
North/South/noSET
Possible settings:
No Set: Standard atmospheric model,
fixed temperature at sea level = 15° C
North: T (temperate), M (mediterranean), A (arid),
tr (tropical), P (polar)
South: T (temprerate), M (mediterranean), A (arid),
tr (tropical)
Selection
mode
„Sync“
Climate zone
Quit mode
„EcoBatt“
Quit mode
„EcoBatt“
Quit mode
„EcoBatt“
Navigation
sub-menus
Quit menu
„Option“
Long pressure:
start mode
„EcoBatt“
Selection
mode
„climate zone“
sleep
- if oF: Beeping activated
- if on: Beeping deactivated
Confirms the new option
and quits the settings menu
- if oF: Beeping activated
- if on: Beeping deactivated
Selection
mode
„sleep“
beep
Changes right
option
Confirms the new
option and quits the
settings menu
Changes left
option
Selection
mode
„beep“
Units
Selection
mode
„Units“
Q
OPTIONS