Sycamore SY2416 User manual

Installaon instrucons : Kinec 12/24 volt Receiver
SycamoreLED.com
LS26 8XT
Technical helpline : 0113 2866686
*Please email [email protected] to register your product
1) Please read these instrucons carefully before commencing any work
2) It is strongly recommended that this unit is installed by a qualied electrician
3) To prevent electrocuon switch the power o at the mains supply before installing or maintaining this ng
4) Ensure others cannot restore the electrical supply without your knowledge
5) The PSU must be rated 12 or 24VDC and be compable with the pre-wired connector system of this product
6) Never exceed the waage stated
IMPORTANT—Please read prior to installaon
TECHNICAL INFORMATION
Thank you for purchasing this SycamoreLED.com product. Please make sure instrucons are followed carefully prior to and during installaon and product
is not altered, otherwise warranty may not be valid. For technical support or warranty informaon please visit www.sycamoreLED.com, or call our dedicat-
ed technical helpline [phone].
APPLICATIONS
1) This LED receiver is exclusively designed for 12 or 24 volt the Light Eming Diode (LED) lamps used indoors.
INSTALLATION
1) The unit conforms to the direcve 2004/108/EC for the electromagnec compability and the low voltage direcve 2006/95/EC.
2) The receiver can only be used with the LED lamps
3) The receiver is only suitable for use indoors. Protect the LED power supply against excessive heat (permissible operang temperature range
–20 to +45 degree C)
4) The loads indicated on the receiver must neither exceed nor below the following values; 0—48W at 12 volt and 0—96w at 24 volt
5) Connect the LED Lamps to the LED receiver with the correct polarity according to the schemac drawing
6) The maximum of the output cable to the LED Lamps should not exceed 2m in order to meet the EMC standard
7) If the LED receiver is used for purposes other than originally intended or it is connected in the wrong way, no liability can be taken over for
possible damages
Input voltage 200-240v +/-10% 50Hz Ambient Temperature ta: Max 45 C
Output voltage 12 or 24Vdc +/-0.5V Case Temperature tc: Max 80 C
Rated power 4Amp Protection degree IP20

Installaon instrucons : Kinec 12/24 volt Receiver
SycamoreLED.com
LS26 8XT
Technical helpline : 0113 2866686
*Please email [email protected] to register your product
1) Connect the controller’s input to the 12/24 volt led driver
2) Press controller “pairing key” for 3 seconds, release when indicator light ashes slowly (ashes once per second)
3) Press the selected kinec energy wall switch once (do not press several mes connuously), when the indicator light goes o it means
pairing is successful.
4) Upto 10 switches can be paired with a single receiver using the above procedure. There is no maximum amount of receivers that can be
controlled by a single switch.
1) Long press the controller “pairing key” for 12 seconds, the indicator light will ash from slowly to quickly. Aer indicator light is o it
means that all paired switch informaon is cleared. If you need to use this controller again, please pair
Pairing to Kinec Switches
TECHNICAL INFORMATION
Thank you for purchasing this SycamoreLED.com product. Please make sure instrucons are followed carefully prior to and during installaon and product
is not altered, otherwise warranty may not be valid. For technical support or warranty informaon please visit www.sycamoreLED.com, or call our dedicat-
ed technical helpline [phone].
Clear Pairing to Kinec Switches
App Download and pairing
Search “Smart Life” in the App store or via Google play. Or scan the qr code below.
IOS Android
Pairing Via Wi
1) Use your mobile phone or tablet device to download the app and follow the prompts to register your account.
2) Click the add device (+) icon, top right in the app and select “lighng” , then the “light source (wi-) ”tab
3) Power on the controller, and conrm the indicator light is ashing quickly (twice per second). If the indicator lights is not ashing quickly,
press and hold the “pairing key” for around 10 seconds, the indicator light will ash from slow to fast to sll, release when the indicator light
is sll. Then wait for 3 seconds and the indicator light will ash quickly (twice per second).
4) Click “conrm indicator light rapidly blink” and enter the Wi password, it will connect aer a period of twenty seconds. The indicator light
will then go o on the receiver, and you will be noed in the app upon successful connecon.
5) Aer the pairing with the network is successful, you can use the mobile app to control, create scenes and set mer controls.
The receivers can also be added to both Amazon Alexa and Google home compable devices via the smart life skills and scanning for devices in the Alexa
and google home app.
On rst installaon the receiver only connects to 2.4GHz Wi-Fi. For hubs with both 2.4GHz and 5Ghz the two bands will need to be separated or the 5Ghz
turned o temporarily.
Pairing Key