01246 200 000 systemq.com
245
4
HD-CAM843 - HD-SDI IR Eyeball Camera With 2.8-12mm Lens
Features
•1080p At 25fps
•True Day Night
•2.8-12mm Varifocal
•40m IR Range
•Wide Dynamic Range
•Adjustable IR Brightness
Specication
FUNCTION SPECIFICATION
CCD 1/3” 2.1 Mega Pixel
Panasonic CMOS
Resolution 1080p @ 25fps
Lens 2.8-12mm Varifocal
Min. Illumination 0 Lux With IRs On
IR LEDs 2 (High Power)
IR Range 40m
Day/Night Mechanical
Digital Zoom
16x
Video Output 1V p~p, 75
Video Connection HD-SDI BNC Socket
CVBS Connection Analogue BNC Socket
Power/Current 12V DC (± 10%) 600mA
Power Connection 2.1mm Socket
Gain Control Automatic
IP Rating IP66
Operating Temp. -10°C ~ +50°C
Dimensions
205 x 98 x 98mm (Ex Bracket)
Options Available
PART CODE DESCRIPTION
HD-CAM843 2.8-12mm HD-SDI All-In-One
All specications are approximate. System Q Ltd reserves the right
to change any product specications or features without notice.
Whilst every eort is made to ensure that these instructions are
complete and accurate, System Q Ltd cannot be held responsible
in any way for any losses, no matter how they arise, from errors
or omissions in these instructions, or the performance or non-
performance of the equipment that these instructions refer to.
This symbol on the products and/or accompanying
documents means that used electronic equipment
must not be mixed with general household waste.
For treatment, recovery and recycling please return
this unit to your trade supplier or local designated
collection point as dened by your local council.
WEE/CG0783SS
Other Products To Consider
1080p HD-SDI
All-In-One IR Camera
With A 2.8-11mm
2.1 Mega Pixel Lens
CAM380
700TVL True Day-Night
Analogue Camera With
2 High Power LEDs,
WDR & UTC.
CAM840
MENU ITEM OPTIONS
MOTION ON / OFF
ON: 1. DET WINDOW:
WINDOW USE: 0~3 3
WINDOW ZONE: ON / OFF
DET HPOS: 0~60 0
DET VPOS: 0~40 0
DET HSIZE: 0~60 60
DET VSIZE: 0~34 34
2. SENSITIVITY: 0~10 5
3. MOTION OSD: OFF / ON
4. TEXT ALARM: OFF / ON
5. SIGNAL OUT: OFF / ON
SYSTEM 1. COM: CAM ID: 0~255 0
BAUDRATE:
2400 / 4800 / 9600
/ 57600 / 115200
2. IMAGE RANGE: USER / FULL / COMP
USER: OFFSET: 0~32 16
3. COLOR SPACE: HDCbCr / YUV / SDCbCr
4. FRAME RATE: 1080_25P / 720_25P /
720_50P
5. MONITOR: 0~3 0
6. FREQ: PAL / NTSC
7. CVBS: ON / OFF
8.
LANGUAGE:
ENG / CHN / CHN S
/ JPN / KOR
9. COLOUR BAR: OFF / ON
10. RESET
EXIT EXIT MENU SYSTEM
Fault Finding
The table below describes common problems and possible solutions.
Fault Possible Cause Possible Solution
Interference On The
Camera Picture
Poor or inadequate cabling
or an unregulated or poorly
regulated power supply.
Make sure you are using a regulated 12V DC power
supply.
No Picture The camera cannot function
without the correct working
power supply.
Test that the camera has the correct voltage
supplying it, you must do this with the camera
connected so that there is load on the PSU. The
camera should have at least 10.5V DC connected to it.
Poor or incorrect cable used.
Check there is and image at the camera end with a
test monitor using the CVBS test output. If there is
a picture here but not at the DVR it could be one of
the following:
A. Video loss in Composite cable as run too long,
usually you would get a picture up to around
100 meters. For longer cable runs you must use
a HD-SDI repeater every 100m. A maximum of
4 repeaters can be used per run.
B. Ensure that the BNC - BNC lead that you
connect between the camera and monitor has
no shorts or open circuits. If you are making
your own lead, don’t forget the lead must have
two wires connected to complete the circuit,
Video and Ground.
The Picture’s Colour
Changes Constantly
Fluorescent lighting emits an
electromagnetic eld which
can cause colour roll.
Move the camera further away form any uorescent
lighting.
Default settings are displayed in blue.
245
For more information on menu options and
what they do see online tip 295
295
