TAKARA DRY-WAVE TG1209 User manual

※The dimensions in （ ）are of TG1609
1330（1730）
1200（1600）
1268（1668）
210（410）455
303
20 20 20 20 20
303 303
455
〜900
800
56
86
4.2
OPERATING ROD
BODY
BODY
BAR
MOUNTING SCREW
for OPERATING ROD HOOK
FIXING SCREW
for BODY
OPERATING
ROD HOOK
MOUNTING SCREW
for BASE
BASE
BASE
Please double check if all the components are included. If there are any missing or damaged parts please contact us or the retailer of the purchased item.
Thank you for purchasing our Up and Indoor Drying Rack. This prod-
uct is intended for hang drying laundry indoors by manually elevat-
ing and lowering a laundry drying pole that is mounted to the
cieling. Please read this guide carefully and exercise safety precau-
tions when using this product.
TG1209 TG1609
1
●This product is intended for indoor use only.
●It is not intended to be used for any other purpose
than hang drying laundry.
Parts Included
Installation Guide
Up and Down
Indoor Drying Rack
Capacity Load Weight : 8kg ※To the installer.
Please hand this guide over to the end user after installation.
①Name of Each Part
The following signs have been used in this Installation Guide
Attach this Installation if product is going to be transferred over to or lent to a third party
For any inquiries concerned with this product, please contact us or the retailer of the purchased item.
Spread of damage is expected Prohibited Actions Necessary to perform

Warning Can result in death or serious injury.
Caution Can cause injury or damage to property.
●It is not intended to be used for any other purpose than hang drying laundry.
●Because this product is intended for indoor use only,
please do not use outdoors or in the bathroom.
●Do not hang laundry that weighs over the 8kg capacity weight.
●Do no use if the pull cord is jammed or stuck.
●Risk of damage to property.
●Risk of damage to property.
●Risk of damage to property.
●Do not play with or swing around the OPERATING ROD. ●Can cause injury or damage to property.
●Stop using the product becomes unstable while using. ●Can cause damage to property.
●Do not install near combustion appliances. Keep away from combustion appliance
or heaters when hanging laundry.
●Install in places where laundry hung will not block or obstruct fire alarms,
heatingand cooling duct outlets, or any other ventilation outlet.
●Can cause injury or damage to property.
●Can cause fire hazards.
●Can cause inadequate ventilation and fire hazards.
●For families with small children, be careful not to hang onto or bump into product. ●Can cause injury or damage to property.
Caution Can cause injury or damage to property.
●When using electric tools, make sure to make the proper torque adjustments.
Refrain from using an Impact Drill.
●Make sure that the location where the base will be mounted is firm and strong.
Mount the base in a leveled location which is firm and strong.
●There may be damaged threads or screws and risk of the
STEEL DRYING RACK falling.
●There may be damaged threads or screws and risk of the
STEEL DRYING RACK falling.
●Can cause damage to property.
●Do not mount in locations where the ceiling has a slope. ●Can cause damage to property.
●Locate the ceiling joist and use a screw that is most suiting.
2
※Decision on the location of mounting should be made after discussing it with owner of the product.
Sign Important Matter Hazards・Damages
Sign Important Matter Hazards・Damages
Sign Important Matter Hazards・Damages
②Safety Cautions
③Mounting Instructions

②Drill a pilot hole and temporarily secure the base by fastening a BASE
MOUNT SCREW in the slot for holding the base in place like in the
figure above. Leave an estimated 4mm space.
③Hang the BASE onto the screw fastened in for holding the base in place
then shift over, like shown in the figure below.
④Other than the screw in step ②, tighten all the other BASE MOUNT
SCREWS to secure the Base. Then tighten the screw fastened in step ②.
⑤Like shown in the figure to the left, check the directional positions of
the Base and the Body then attach the Body to the Base until a snap-
ping in place sound is heard.
⑥Check to see if the Base is stable
⑦Secure the Body using the 4 FIXING SCREWS for the BODY
⑧Mount the wall hook for the operating rod.
Decide on where to mount the hook. Then temporally hold the hook
in place with double-sided tape. Push the hook in place so that the it
doesnʼ t spin around and then fasten in the HOOK MOUNTING SCREW
(4×16).
⑨Double-check that the equipment functions properly.
After installing the equipment, check if the following functions oper-
ate properly.
・If the Body is securely mounted.
・If the pole elevates and lowers properly.
・If the pole is leveled when being stored away
・If the equipmentʼs locking mechanism functions properly.
・If the pole is leveled in its stored position.
①Decide on the
location to mount.
210（410）
（Edge of the BODY）
210（410）
（Edge of the BODY）
Where the Pitch of Ceiling Joist is 455 mm
Where the Pitch of Ceiling Joist is 303 mm
455455
43 303303303
210（410）
（Edge of the BODY）
210（410）
（Edge of the BODY）
Where the Pitch of Ceiling Joist is 455 mm
Where the Pitch of Ceiling Joist is 303 mm
455455
43 303303303
Slots for Holding Base in Place OPERATING ROD
OPERATING ROD
BASE
BASE
Slots for Holding Base in Place
Please read before mounting
4mm
3
●Discuss with the owner of the product before deciding on whether to place the lock part (location of the OPERATING ROD) on the right or left side.
Shown in the figure below, the LOCK part of the BODY should go on the right side of the 4 holes on the side of base can be seen. In addition, make
sure there is enough space for the screwdriver when mounting with a screw through the round whole on the side of the base.
●The screw that is included cannot be used if the ceiling is made of concrete. In such cases, please discuss with the manufacturer or a specialist.
●Please use a pan head screw if a screw other than the one that is included is going to be used.
※Mount the base respective to the 303 or 455mm pitch of the ceiling joist.
Push into place
until a snap
is heard
③
Check to see if the
slot on the side of
the base and the
thread groove of
the body are on
the same side.
⑦
⑦⑦
⑦⑦
⑤-2
⑤
Hang at first
Locking Part
⑤-1
※The dimensions in（ ）are of TG1609
BE AWARE that the body needs to be placed in the proper direction
when fastening the BODY MOUNT SCREWS ⑦. With the locking
mechanism on the right-hand side, positioning yourself towards
the front of the body, fasten the FIXING SCREW for the body.
Sectional view

Caution Can cause injury or damage to property.
●Do not elevate or lower the pole with laundry hung on the pole.
●Hanging laundry unevenly with more weight on one side than the other.
●Can cause damage to property.
●Can cause damage to property.
●Do not use during high winds. ●Can cause damage to property.
●Store away the pole when not in use. ●Can cause injury or damage to property.
●Stop using if the cord gets tangled up, starts to wear-down or
if any other complications arise. ●Can cause injury or damage to property.
●Do not pull on the cord itself or lower the pole in a slant position.
●Do not consecutively elevate and lower the pole.
●Can cause damage to property.
●Do not forcefully lower the pole more than 900mm from the ceiling. ●Can cause the equipment to break.
●Can cause the equipment to break.
※The operating rod should always be
perpendicular to the pole
※The operating rod should always be
perpendicular to the pole
※The colored part is an indicator of the tip of the rod
1.To Lower the Pole
Insert the tip of the Operating Rod into the slot located at the center
of the pole, Then rotate it 90 degrees slowly lowering the pole to the
height of preference.
2.Lock the pole in place (or unlock)at the preferred height.
Locked Unlocked
■How to Lock
Make sure that the pole is locked into place when hanging clothes.
Leave the operating rod locked in place and do not forcefully remove
the operating rod.
Insert the tip of the operating rod
into the long slot in the body and
rotate it 90 degrees clockwise.
（Do not remove the rod）
■How to Unlock
Rotate the inserted operating rod
90 degrees counterclockwise and
remove the operating rod.
4
④Operational Instructions
Sign Important Matter Hazards・Damages

4〜5cm
3.To Store Away the Bar
Slowly pull the center of the bar down using your hand about 4-5cm
then release the bar.
To lower the bar to a
lower height
To raise the bar to a
higher height
※When the bar is slanted（Horizontal Adjustment）
After installment, elevate and lower the bar 2 or 3 times to fit in
the cords and make adjustments to level out the bar.
The adjustment to one side of the cords is about ±5mm. If there is
any resistance when adjusting the screw, refrain from making any
further adjustments and readjust the opposite cord.
※If there is problems storing away the bar via the process mentioned above, then
lower the bar to the very bottom and try the process over again.
※If the bar sways when storing away and
does not get stored back in storage
place, then push up the bar up.
Moreover, the bar stores away more
smoothly when pushed up with the
operating rod.
If the bar becomes unleveled while operating, then make adjustments to the
screw at the tip end of the bar to level the bar out, shown in the figure.
■Things to be careful about when hanging laundry.
・Do not apply all the load weight on
only one part of the pole.
・Do not hang over 8kg of laundry. ・Hang the laundry evenly across the pole.
5
Do not consecutively elevate and lower the bar.
Moreover, Don not forcefully pull the bar down too fast.
■Reference to how much laundry can be hung onto this product.
For example, 1 day load of laundry
for a family of 4.
Long Sleeve White Dress Shirt・Blouse 4Pieces
Short Sleeve Shirt・T Shirt 4Pieces
Socks (using a sock drying rack)5Pieces
Bath Towel 2Pieces
Sweat Suits 2Pieaces
Total Est. 7.5kg
Est. 250g
Est. 200g
Est. 200g
Est. 150g
Est. 500g
Est. 900g
Est. 1000g
Est. 600g
Est. 300g
Long Sleeve White Dress Shirt（Mixed Fabric）
Short Sleeve Shirt（Mixed Fabric）
T Shirt（Cotton）
Towel（Cotton）
Bath Towel（Cotton）
Sweat Suit（Cotton）
Jeans（Cotton）
Skirt（Mixed Fabric）
Kids Skirt Pants（Mixed Fabric）
Weight of Laundry
（to be used as a reference）At time of Spin Dry
〈researched by our company〉

200115
Item Number: TG1209/TG1609
Gross Weight: 3100g/3800g
Product Name: Up and Down Indoor Drying Rack
Purpose: Indoor Laundry Drying Rack
Material: Aluminum, Stainless, Steal, ABS, POM, PA6resin, etc.
Country of Origin: China・Japan Finished: Japan
Q.The pole doesnʼt elevate and lower smoothly.
A.Is the cord not tangled or worn-out? Please fix the tangle or ware-out.
A.Is there any laundry jammed on the bar? Remove any laundry from the bar.
1.Wet and wring out a soft cloth to wipe off any dirty spots.
2.For stains and other spots that are hard to remove, use a soft
cloth with diluted neutral detergent to rub off.
Q.The BODY is unstable.
A.Stop operating and consult directly with the contractor.
6
⑦
⑤
Caution Can cause injury or damage to property.
●Perform periodic check ups on whether the rack is stable or not. ●Can cause injury or damage to property.
●When cleaning the rack, do not use thinners, benzine or alcohol,
or any other type of glass cleaner that may contain organic solvents.
●Risk of causing the surface of the rack to dissolve, deform or distort in
some way.
●Do not use a hard brush or scrub brush. ●Can cause damage to equipment.
Maintaining the Rack
⑥Thinking, Did It Breakdown?
Basic Specifications
Sign Important Matter Hazards・Damages
2-2-30NagataEminenceBld.2F,
NagataNaka,HigashiOsaka-City,Osaka,
577-0013,Japan
TEL:[phone]
https://www.takaranet.co.jp/eng/
TAKARAINDUSTRYCO.,LTD.