Team Corally C-53008 User manual
When you enter this screen, press and to choose the right neutral pulse
position of the servo and enter to frequency setting.
Press and to choose the right frequency and enter swing/manual screen.
In this screen, press and to change the amplitude of the pulse width.
In this screen, press and to change the pulse width and
check the response of the servo to different pulse width.
ESC Settings
Li-Po Battery Analyzer
The Smartbox can check the total cell number, total voltage, each cell voltage, highest voltage and lowest
voltage and the voltage difference between the highest voltage and lowest voltage.
Servo Tester
The Smartbox can check the input voltage, servo travel position and peak current of your servo.
The default servo neutral position is 1520us/100Hz and 760us/100Hz. If the testing servo is not
1520us/100Hz and 760us/100Hz, please enter CUSTOM and set the servo neutral position (range: 200-
2000us) and frequency(range: 50-200Hz) by yourself.
There are two kinds of mode “Swing Mode” and “Manual Mode” to make the servo swing and check
the servo travel position.
Swing Mode: The Smartbox will send out a signal to make the servo swing automatically
Manual Mode: The Smartbox allows you to change the PPM signal and check the servo’s response to the
signal.
Input PPM Signal Monitor
The Smartbox can check the output voltage from the receiver, the receiver’s PPM signal / pulse width and
frequency.
Connect the Smartbox as
shown, turn on the ESC and
follow these steps.
Press button to enter
different programmable items,
press or buttons
to browse all the options and
press button to confirm
your selection and then the
screen will go back to the main
program menu
Connect the Smartbox and the battery as shown, monitor battery voltage as follows
Connect the Smartbox with the receiver as shown, and
turn on the ESC and the transmitter. Please note that the
Smartbox must be inserted in the Throttle Channel and
a RX powerpack or the ESC can be inserted to any free
channel of the receiver to supply power to the receiver.
When all is connected, the Smartbox will display the output
voltage from the receiver, the receiver’s frequency and the
neutral pulse position.
Hold full throttle and hold full brake to check the receiver’s
PPM signal / pulse width.
Safety Notes
• This Smartbox is not a toy and only suitable for users from age 14+
• Never allow water, moisture, oil or other materials to get in contact or inside the Smartbox. It may damage
the Smartbox completely.
• Never disassamble the Smartbox or modify the components on the PC board
• We strongly suggest to use the original wires and connectors supplied in the ESC packaging
• To avoid short circuit, please keep the connectors away from any metal parts.
• Never connect a battery with reversed polarity.
Team Corally can never be held responsible for any damage caused or related to the
non-compliance with the above instructions.
Suitable for Cerix Pro 120
Cerix Pro 120 1S
Cerix PRO 160
Revoc Pro 160
...
Input Voltage 6 - 10V DC
Input Current 500mA
Idle Current < 20mA
Dimensions 85x55x13mm
Weight 46g
Technical SpecificationsConnectivity
Features
• ESC Settings
• Servo Tester
• PC Interface - Link ESC to PC
• Motor KV/RPM Tester
• Input PPM Signal Monitor
• LiPo Battery Analyzer
Introduction
Setting up all parameters of your ESC made easy with this digital
programmer. The bright LCD screen let you run through all the
programs and within seconds the values have been changed. This
programmer can also be used as interface between your PC and
the ESC to update your firmware or to do even more set-ups.
The TC Smart Box offers six-in-one functions:
Functions
ESC Setting
The TC Smartbox can work as an individual device to program the ESC. The options of each parameter are
displayed on the LCD screen.
Servo Tester
The TC Smartbox can check the input voltage, servo travel position and peak current of your servo.
PC Interface
The TC Smartbox can work as an USB adaptor to link the ESC with your PC.
The user can update the firmware of the ESC or program the ESC by the TC CONNECT software on PC.
Motor KV/RPM Tester
The TC Smartbox can check the motor KV, RPM and input voltage.
Input PPM Signal Monitor
The TC Smartbox can check the output voltage from the receiver and the receiver’s PPM signal/pulse width
and frequency.
LiPo Battery Analyzer
The TC Smartbox can be used as a batterypack analyzer and tester to check the total cell number, total volt-
age, each cell voltage, highest voltage and lowest voltage and the voltage difference between the highest
voltage and lowest voltage.
INSTRUCTION MANUAL TC SMART BOX
Application
There are 4 program buttons on the TC Smartbox
Press this button to ENTER into the referred menu or to CONFIRM your selection
Press this button to PAGE DOWN or SCROLL DOWN in the menu / selection
Press this button to PAGE UP or SCROLL UP in the menu / selection
Press this button to EXIT and go back to previous menu
Page 1 Page 2 Page 3 Page 4
Battery Balance
Connector
Motor Sensor
Connector
LCD Screen
2 Lines - 16 Characters
USB to PC
I/O Connector
ENTER key
INC+ key (Up)
DEC- key (Down)
EXIT key (Esc)
ENTER
DEC-
DEC-
INC+
INC+
EXIT
ENTER
ENTER
EXIT
ENTER
ENTER
ENTER
When the screen displays the programed item, you can press the button to go back to the main
program menu and start to program next item.
Note: The programmable items in the menu may be differ between the different type of ESC’s
DEC-
DEC-
DEC-
DEC-
DEC-
DEC-
INC+
INC+
INC+
INC+
Connect RX Power
4.8 - 7.4V
or
ESC with battery
connected
ENTER
*Remark 1
*Remark 2
*Remark 3
ENTER ENTER
ENTER
ENTER
ENTER
ENTER
INC+
INC+
INC+
DEC-
DEC-
DEC-
CORELESS- TITANIUM GEAR
HIGH VOLTAGE 6V - 8.4V
HIGH SPEED
Warranty and Service
If material defects or manufacturing faults should arise in a product distributed or manufactured by Team Corally,a division
of JSP Group Intl BVBA, and purchased by a consumer, weTeam Corally acknowledge the obligation to correct those faults
or defects within the limitations described below. This manufacturers warranty is in addition to, and does not affect, the
legal or contractual rights of the consumer which arise from the purchase of such products. Team Corally guarantees the
consumer that its products are free from material, manufacturing, and construction faults, as determined by the general
state of knowledge and technology valid at the time of manufacturing. The fault responsible for causing the damage must
be proven to have been present in the product at this time. Claims for compensation arising from consequential damage
or product liability will not be considered valid unless they fall under premptory provisions of the law. If material defects or
manufacturing faults should arise in a product distributed or manufactured by Team Corally in the European community
(EC) and purchased by a consumer,then Team Corally undertakes to correct those defects within the limitations described
below.
This manufacturer’s declaration does not affect the consumer’s legal or contractual rights regarding defects arising from
the purchase contract between the consumer and the dealer or reseller.
Extend of the Warranty
If a claim is made under warranty, we take at our discretion to repair or replace the defective goods. We will not consider
supplementary claims, especially for reimbursement of costs relating to the defect (e;g. installation / removal costs) and
compensation for consequent damages unless they are allowed by statute. This does not affect claims on legal regula-
tions, especially according to the product liability law.
Provisions of the Warranty
The purchaser is required to make the warranty claim in writing, and must enclose original proof of purchase (e.g. invoice,
receipt, delivery note) and the appropriate warranty card. He must send the defective goods to our local represen-
tatives or directly to Team Corally, a division of JSP Group Intl BVBA, Geelseweg 80, 2250 Olen,
Belgium at his own risk and cost.
The purchaser should state the material defect or manufacturing fault, or symptons of the fault, as accurate as possible,so
that we can check if our warranty obligation is applicable. The goods are transported from the consumer to us, and from
us to the consumer, entirely at the risk and cost of the consumer.
Invalidation of the Warranty
The consumer cannot make a claim under warranty when the fault is affecting the use of the product arising from nat-
ural wear, competition use, or improper use (including installation) or external forces. The consumer’s adherence to the
building and operating instructions relevant to the model, including the installation, operation,use of, and maintenance of,
model-related components cannot be supervised by Team Corally.Therefore Team Corally is in no way liable for loss, dam-
age, or costs resulting from improper use, or behaviour in any way connected to the above described provisions. Unless
otherwise required by law, Team Corally is in no way whatever liable to provide compensation for damages arising from
the improper use of the model (including personal injury, death, damage to buildings, loss of turnover,loss of business, or
interruption of business, or any other direct, or indirectly caused, consequential damage).
Duration of Validity
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in the European
Community (EC) counted from the date of purchase. The claim period is 12 months from the date of purchase of the
product by the consumer from a dealer outside the European Community (EC) counted from the date of purchase. If a
defect arises after the end of the claim period, or if evidence or documents required according to this declaration in order
to make the claim valid are not presented until after this period, then the consumer forfeits any rights or claims from this
declaration. The guarantee period is not prolonged by the granting of any claims within the framework of this warranty,
especially in the case of repair or replacement. The guarantee period also does not restart in such cases.
Warranty Expiration
If we do not acknowledge the validity of a claim based on this declaration within the claim period, all claims based on this
declaration will expire after six months from the time of registering the claim; however this cannot occur prior to the end
of the claim period.
Applicable Law
This declaration, and the claims, rights and obligations arising from it,are based exclusively on the pertinent Belgium Law,
without the norms of international private law, and excluding UN retail law. Place of fulfilment for liabilities arising from this
declaration is Olen, Belgium. Court of jurisdiction is Turnhout, Belgium.
Copyright
This manual is protected by a copyright. Any publication, transmission or commercial use of this manual is prohibited
without written permission. Team Corally and JSP Group Intl BVBA assumes no responsibility for printing errors in this
manual. This manual is subject to technical changes.
WEEE: At the end of this device’s useful life, please remove all the batteries and dispose of them
separately. Take electrical appliances to the local collection points for waste electrical and elec-
tronic equipment. Other components can be disposed of in domestic refuse.
Thank you for your co-operation!
Declaration of Conformity
Team Corally SMARTBOX
Declaration of conformity in accordance with the statutory rules 426/2000
and directive 1999/5/EC (R&TTE)
Team Corally, a division of JSP Group Intl BVBA declares under sole responsibility that the Smartbox programmer
with reference nr C-53008 to which this declaration relate, conforms with the following harmonized standards
and EU legislations;
EN 60950-1 ed. 2
EN 61000-6-3 ed. 2
Olen - Belgium
12 March 2016
Stefan Engelen
Ceo
Page 5 Page 6 Page 7 Page 8
Team Corally
Geelseweg 80
2250 Olen
Belgium
Tel: +32 14 25 92 94
Motor KV/RPM Tester
The Smartbox can check the motor KV, RPM and input voltage.
PC Interface - Connect ESC to PC
The Smartbox can be used to link the ESC with your PC. You can update the firmware of the ESC or
program the ESC using the TC Connect software.
ENTER
INC+
INC+
DEC-
DEC-
Connect the Smartbox with the ESC, receiver, motor, motor sensor cable and battery as shown, and turn on
the ESC and set the pole number (range: 2, 4, 6, 8,...28.) of the motor by pressing and
button.
After you set the motor pole number, move the trigger to get the motor KV and when the trigger is moved
to full throttle, you can read the motor RPM value from the screen.
> to PC
ENTER
Connect the Smartbox as shown, turn on the ESC and proceed
When the above screen is displayed, you can start to program the ESC using the PC.
Note: Please click FIRMWARE UPDATE to check whether there is an updated version for the Smartbox.
If you find an update for the Smartbox, please click UPDATE to update your Smartbox.
INSTRUCTION MANUAL TC SMART BOX
