Team losi Ten mt User manual

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

2TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Age Recommendation: Not for children under 14 years. This is not a toy.

CONTENTS

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in dam-

age to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and

responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with

incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and mainte-

nance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon

Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM

or Spektrum.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.

For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

updates and more. Click on the Support tab at WWW.LOSI.COM and follow the product

registration link to stay connected.

COMPONENTS

• Losi®TEN-MT RTR with AVC® technology: 1/10-Scale 4WD Monster Truck (LOS03006 T1/T2)

• Spektrum™ DX2E 2.4GHz Transmitter (SPM2330)

• Spektrum™ 4-Channel DSMR®AVC Surface Receiver (SPMSRS4201)

• Spektrum™ 9KG 23T Waterproof Servo (SPMS605)

• Dynamite®Fuze™ 130A Sensorless Brushless Waterproof ESC (DYN4955)

• Dynamite®Fuze™ 550 Brushless Motor 3800Kv (DYNS1616)

• 4 AA batteries (for transmitter)

TABLE OF CONTENTS

CONTENTS.................................................................................................................2

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS.........................3

QUICK START.............................................................................................................3

CHARGING THE BATTERY.........................................................................................3

INSTALLING THE BATTERY........................................................................................4

SPEKTRUM DX2E RADIO SYSTEM...........................................................................4

SRS4201 AVC TECHNOLOGY RECEIVER ................................................................4

INSTALLING THE TRANSMITTER BATTERIES...........................................................4

SRS4201 STABILITY ASSIST RECEIVER....................................................................5

DRIVING PRECAUTIONS...........................................................................................5

POWERING ON THE VEHICLE...................................................................................5

BEFORE RUNNING YOUR VEHICLE ..........................................................................5

AVC SENSITIVITY ......................................................................................................5

DISABLING AVC.........................................................................................................6

PERFORMING A CONTROL DIRECTION TEST..........................................................6

RUN TIME...................................................................................................................6

CHANING THE TRAVEL ADJUST SETTINGS..............................................................6

DYNAMITE FUZE 130A SENSORLESS BRUSHLESS ESC (DYN4955)......................6

DYNAMITE FUZE 3800KV BRUSHLESS MOTOR (DYNS1616) ................................8

TROUBLESHOOTING GUIDE .....................................................................................8

LIMITED WARRANTY ................................................................................................9

FCC INFORMATION............................................................................................10

IC INFORMATION...............................................................................................10

WARRANTY AND SERVICE CONTACT INFORMATION ..........................................10

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION................................10

REPLACEMENT PARTS ......................................................................................36–37

OPTIONAL PARTS....................................................................................................37

EXPLODED VIEWS.............................................................................................38–41

As the user of this product, you are solely responsible for operating in a manner that does not

endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside

your control. This interference can cause momentary loss of control, so it is advisable to

always keep a safe distance in all directions around your model as this margin will help avoid

collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor,

electronic speed control and battery, because they generate high temperatures. You may

burn yourself seriously touching them.

• Do not put ﬁngers or any objects inside rotating and moving parts, as this may cause

damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car.Always turn off

the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio

equipment.

SAFETY PRECAUTIONS AND WARNINGS

2TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Your new Horizon Hobby vehicle has been designed and built with a combination of

waterproof and water-resistant components to allow you to operate the product in many

“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your

vehicle should NOT be treated like a submarine. The various electronic components used in the

vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how-

ever, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts

in the electrical cables, will be susceptible to corrosion if additional maintenance is not

performed after running in wet conditions. To maximize the long-term performance of your

vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose to run in wet

conditions. If you are not willing to perform the additional care and maintenance

required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and

complying with the following precautions could result in product malfunction

and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you

have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before

use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the

manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water

is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certiﬁed

as water-resistant or waterproof. If the motor becomes excessively wet, apply very light

throttle until the water is mostly removed from the motor. Running a wet motor at high

speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of

operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or

larger spur gear. This will increase torque (and motor life) when running in mud, deeper

puddles, or any wet conditions that will increase the load on the motor for an extended

period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the

body removed, place the vehicle upside down and pull full throttle for a few short bursts

until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose or hanging objects

away from rotating parts when performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can

of compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a

garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove

any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing

light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue

to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings

with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

QUICK START

Please read the entire manual to gain a full understanding of the TEN-MT RTR vehicle, ﬁne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings

and instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline

or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to

initialize. Always power the transmitter ON before the vehicle and power it OFF

after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos

are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

Choose a battery designed to work with the Dynamite®Fuze™ 130A Sensorless BL

Waterproof ESC. We recommend the Dynamite®7.4 5000mAh 2S 30C LiPo: Hardcase

with EC3™ connector (DYN9005EC). Choose a charger designed to charge 2S Li-Po

batteries. We recommend the Dynamite®Prophet™ Sport Li-Po 35W AC Battery Charger

(DYNC2005CA). Refer to your battery and charger manuals for usage, safety, and charging

information.

CHARGING THE BATTERY

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

4TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

INSTALLING THE BATTERY

1. Ensure the ESC is powered OFF

2. Turn the vehicle over.

3. Turn knob to release the battery door.

4. Install the fully charged battery in the vehicle.

5. Connect the battery to the ESC.

6. Close the battery door and twist the lock.

7. Power ON the transmitter, then the vehicle.

IMPORTANT: Secure the ESC wires so they do not interfere

with the gearing.

SPEKTRUM DX2E RADIO SYSTEM 1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. BIND Button Puts the transmitter into Bind Mode

4. ON/OFF Switch Turns the power ON/OFF for the transmitter

5. ST. REV Reverses the function of the steering when the wheel is turned left or right

6. Indicator Lights

-Solid green light—indicates adequate battery power

-Flashing green light—indicates the battery voltage is critically low. Replace batteries

7. TH. REV Reverses the function of the speed control when pulled back or pushed forward

8. ST Trim Adjusts the steering center point

9. TH Trim Adjusts the throttle neutral point

10. ST Rate Adjusts the sensitivity of AVC

11. Antenna Transmits the signal to the model

SRS4201 AVC TECHNOLOGY RECEIVER

12. BIND

13. DISABLE

14. AUX 2

15. AUX 1

16. THR

17. STR

INSTALLING THE TRANSMITTER BATTERIES

1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.

2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the

transmitter’s battery case.

3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries.

Charging non-rechargeable batteries may cause the batteries to burst, resulting

in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose

of used batteries according to national regulations.

For more information on the transmitter, go to www.horizonhobby.com and click

on the support tab for the Spektrum DX2E to download the instruction manual.

4TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power,

you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is

not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries dis-

charged to a voltage lower than the lowest approved voltage may become dam-

aged, resulting in loss of performance and potential ﬁre when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.

Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Remove the body from the vehicle.

4. Connect a fully charged battery pack to the ESC.

5. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a ﬂat, level surface and motionless for at least 5

seconds.

6. Re-install the body on the vehicle.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement.All suspension arms and steering components

should move freely. Any binds will cause the vehicle to handle poorly.

Tip: To increase the ride height and ground clearance of your vehicle, install the included

shock spacers. The stock shock spacer measures 4mm. You can add one or both of the

medium (2 mm) and/or small (1 mm) spacers to increase vehicle height and ground

clearance.

2. Charge a battery pack.Always charge the battery pack as per the battery and/or

charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim

so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

AVC®SENSITIVITY

The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the

sensitivity, the AVC®system becomes more sensitive to the vehicle drifting left or right.You

would use maximum sensitivity during high speed driving or drag racing, when you want

the vehicle to stay in a straight line. As the sensitivity value increases, the amount of

steering travel decreases.

Turn the ST RATE knob counter-clockwise to reduce the sensitivity.

Turn the ST RATE knob clockwise to increase the sensitivity.

IMPORTANT: The ST RATE knob will only adjust the sensitivity when

the transmitter is bound to a DSMR®receiver. When the transmitter

is bound to a DSM®, DSM2®or DSM Marine receiver,

the ST RATE knob controls the steering dual rate.

SRS4201 STABILITY ASSIST RECEIVER

AVC®– ACTIVE VEHICLE CONTROL™

The Spektrum SRS4201 receiver features Active Vehicle Control™(AVC®) technology that

responds similar to traction control in full-scale vehicles. In addition to traction control,AVC

technology also increases steering stability during high speed driving or while driving over

rough terrain.As you increase the AVC sensitivity, the system increases steering stability and

traction control, similar to reducing the amount of steering rate in a computer transmitter.

Reducing the sensitivity value increases the amount of steering control from the transmitter.

The SRS4201 receiver also enables you to quickly turn AVC on or off if you participate

in organized racing.

IMPORTANT: You must use digital servos with the SRS4201 receiver. Do not use analog

servos as they willl reduce the performance of the system and may cause overheating.

CALIBRATING THE RECEIVER

1. With the vehicle on a ﬂat, level surface, insert the Bind Plug in the BIND port on the

receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The orange LED ﬂashes, indicating the receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Press and hold the BIND button while powering on the transmitter.

6. Release the BIND button when the orange LED slowly ﬂashes.The transmitter and receiver

are linked when the orange LED is solid.

7. Pull the transmitter trigger to Full Throttle.

8. Push the transmitter trigger to Full Brake, then return the trigger to center.

9. Turn the transmitter steering wheel to Full Right.

10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.

The orange LED ﬂashes once.

11. Remove the Bind Plug, then power off the receiver to save the settings.

12. Power off the transmitter.

FORWARD BRAKE/REVERSE

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

6TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-SCBE RTR, AVC: 1:10 4WD SCBE • INSTRUCTION MANUAL

DISABLING AVC® TECHNOLOGY

If you participate in organized racing, you may be required to turn AVC off. To turn AVC off:

1. Insert a Bind Plug in the BIND port on the receiver.

2. Insert a second Bing Plug in the DISABLE port on the receiver.

3. Connect a fully charged battery pack to the ESC.

4. Power on the ESC. The orange LED ﬂashes, indicating the receiver is in bind mode.

5. Center the ST TRIM and TH TRIM dials on the transmitter.

6. Press and hold the BIND button while powering on the transmitter.

7. Release the BIND button when the orange LED slowly ﬂashes.The transmitter and receiver

are linked when the orange LED is solid.

8. Pull the transmitter trigger to Full Throttle.

9. Push the transmitter trigger to Full Brake, then return the trigger to center.

10. Turn the transmitter steering wheel to Full Right.

11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.

The orange LED ﬂashes once.

12. Remove the Bind Plugs, then power off the receiver to save the settings. The receiver will

continuously blink to indicate AVC is disabled.

13. Power off the transmitter.

IMPORTANT: You must calibrate the receiver each time it is placed in bind mode.To activate

AVC, see the steps in "Calibrating the Receiver."

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating

increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.

The battery connectors may become hot during driving. Batteries will lose performance

and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries

and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the

vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move

forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel

input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to

turn the steering wheel.

CHANGING THE TRAVEL ADJUST SETTINGS

1. Hold the trigger in the full brake position and turn the steering wheel to Full Right while

powering on the transmitter. The LED ﬂashes rapidly, indicating the programming mode is

active.

2. Throttle End Point: Continue holding full throttle.Turn the TH TRIM knob to adjust

the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob

to adjust the full brake end point. Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left position. Turn

the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST

TRIM knob to adjust the right end point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.

The minimum Travel is 75%, and the Maximum travel is 150%.

IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate

the SRS4201.

SPECIFICATIONS

Type Sensorless

Constant/Peak 130A/760A

Resistance 0.0004 Ohm

Function Forward/Brake–Forward/Brake Reverse

Operation Proportional forward, proportional reverse with braking delay

Input Voltage 7.4V–14.8V (The motor in this vehicle will not support 14.8V)

BEC Output 6V/3A

Overload Protection Thermal

Dimensions (LxWxH) 53.5mm x 36mm x 36mm

Weight 79 g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the input voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause

(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that

the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON.

If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause

(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

DYNAMITE®FUZE™ 130A SENSORLESS BRUSHLESS ESC (DYN4955)

For sensorless brushless motors:

1. Connect the ESC terminal A (typically designated by a blue wire) to the motor’s terminal

A (red wire on a Dynamite®Fuze™ sensorless motor). This may also be changed in

Programming Item 12, Motor Rotation, without changing wire connections.

2. Connect the ESC terminal B (typically designated by a yellow wire) to the motor’s terminal

B (blue wire on a Dynamite®Fuze™ sensorless motor).

3. Connect the ESC terminal C (typically designated by an orange wire) to the motor’s

terminal C (black wire on a Dynamite®Fuze™ sensorless motor).

NOTICE: Always disconnect the battery from the ESC when you have ﬁnished operating

your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC

will continue to draw current when connected to the battery, resulting in possible dam-

age to the battery through over discharge.

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is

neutral and the throttle travel range is at 100%. Disable any special functions such as

ABS, etc.

3. Press the SET button while powering ON the ESC. Release the button as soon as the red

LED starts to ﬂash.

4. Calibrate the throttle points by pressing the SET button once after each step.

- Neutral (1 ﬂash)—leave the throttle at rest, untouched

- Full throttle (2 ﬂashes)—pull the throttle fully back

- Full brake/reverse (3 ﬂashes)—push the throttle fully forward

5. The motor will run 3 seconds after the last step is completed.

Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside

motor wires. The center wire must remain in the center and cannot be moved to another

motor tab.

6TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

DESCRIPTIONS

1. Running Mode

-Forward Only with Brake

Intended for competition use, this mode allows only forward and brake controls.

-Forward/Reverse with Brake

This mode is the basic all-around mode, allowing forward, reverse and brake controls.

To engage reverse while moving forward, apply the brake until the vehicle has come to

a complete stop, release brake, then apply the brake again. While braking or in reverse,

engaging the throttle will result in the vehicle immediately accelerating forward.

2. Drag Brake Force

Adjusts the amount of brake automatically applied when the throttle is returned to the

neutral position.This simulates the engine braking effect of a full-scale vehicle, allowing

improved turn-in and your vehicle’s general response to controls.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the

battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output

power shuts off and the red LED ﬂashes twice repeatedly.

The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,

if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery

pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a

8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po

battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives

a very soft initial acceleration and level 4 gives a stronger initial acceleration.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking,

but can also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Initial Brake Force (minimum brake)

Adjusts the minimum amount of braking power when the brakes engage. The default

value is equal to the drag brake value. A high value can lock the wheels when the brake

is used.

8. Neutral Range

Adjusts the throttle sensitivity around the neutral point.A higher value results in the

throttle having to be moved more for the vehicle to move forward, backward or brake.

9. Timing

Adjusts the motor drive current timing. More timing gives more performance, but can

lower efﬁciency and cause damage to the motor and/or ESC by overload or overheating.

NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor

timing correctly can result in damage to the motor and ESC. Refer to the manufacturer

instructions for recommended timing settings.

The Following Programmable Items require the optional Digital ESC Program Box:

10. and 11. Available Items are subject to ﬁrmware updates to the ESC and the optional

digital program box.

12. Motor Rotation

Allows you to make this change in the ESC so no wires need to be changed between the

ESC and the motor.

13. Li-Po Cells

Allows the ESC to automatically detect or manually set the number of cells in your Li-Po

battery back.

PROGRAMMABLE ITEMS

Basic Items

PROGRAMMABLE VALUE Default Settings

1 2 3 4 5 6 7 8 9

1 Running Mode Forward w/ brake Forward/Reverse w/ brake Forward/Reverse

2 Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%

3 Low Voltage Cutoff non-protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

4 Start Mode Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9

PROGRAMMABLE ITEMS

Advanced Items

PROGRAMMABLE VALUE Default Settings

1 2 3 4 5 6 7 8 9

5 Max Brake Force 25% 50% 75% 100% disable

6 Max Reverse Force 25% 50% 75% 100%

7 Initial Brake Force = Drag Brake Force 0% 20% 40%

8 Neutral Range 6% (Narrow) 9% (Normal) 12% (Wide)

9 Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º

10 Reserved Item

11 Reserved Item

12 Motor Rotation Counterclockwise Clockwise

13 Li-Po Cells Auto Calculate 2 Cells 3 Cells 4 Cells 5 Cells 6 Cells

ESC FUNCTIONS AND MODES

The ESC includes programming options so you can adjust the way your vehicle performs.

Refer to the included settings table to adjust the ESC for your driving conditions.

ESC PROGRAMMING PROCEDURE

Programming is accomplished using the SET button on the ON/OFF switch or Digital Program

Box (DYNS3005).

1. Connect a fully charged battery to the ESC.

2. Power ON the ESC using the ESC switch.

3. Hold the SET button for 1 second until the green LED blinks, then release the SET button

to enter programming mode.

4. Press and release the SET button as needed to get to the desired menu option (the Green

LED will blink corresponding to the menu item number). Programming menu items 1

through 9 are accessible using the SET button on the ESC. Programming menu items 10 and

above are only accessible using the optional ESC programming card. Programming of menu

items 10 and 11 is only possible after ﬁrmware updates to the ESC programming card.

5. When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks.

6. Press the SET button to move among the settings based on how many times the red LED

blinks (Refer to the table for more information).

7. Save the setting by holding the SET button for 3 seconds.

8. Power OFF the ESC switch and repeat the instructions above to change other settings.

Tip: If desired, the ESC programming can be returned to default settings

by powering ON the ESC and holding the SET button for 5 seconds.

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

8TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing for the stock platform. It offers an

ideal balance between speed, power and efﬁciency. Should you decide to customize your

vehicle with optional batteries or motors, it may be necessary for you to change the pinion or

spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater

torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with

fewer teeth will reduce torque and increase top speed. Care should be taken when installing

larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor

and ESC. When testing different gearing options, pay close attention to the temperature of

the motor and speed control to ensure you are operating within the temperature range of the

components. The motor or ESC should never be so hot that it cannot be touched. If tempera-

tures are too hot, a different gearing combination with a lower pinion gear and/or higher spur

gear is suggested.

CHANGING THE PINION GEAR/GEAR RATIO

1. Unscrew the gear cover screw and remove the gear cover.

2. Loosen the motor screws and slide the motor back.

3. Place the new pinion on the end of the motor shaft so the set screw is located

over the ﬂat on the shaft.

4. Position it so the teeth line up with the spur gear and secure the pinion by tightening

the set screw.

5. Set the gear mesh.

6. Reinstall the gear cover.

DYNAMITE®FUZE™ 3800KV BRUSHLESS MOTOR (DYNS1616)

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting it is only necessary when changing

motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When

the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If

the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Unscrew the gear cover screw and remove the gear cover.

2. Loosen the motor screws and slide the motor back.

3. Put a small piece of paper between the pinion and spur gears.

4. Push the gears together while tightening the motor screws.

5. Remove the paper. Check the mesh at 3–5 different locations around

the spur gear for a small amount of movement.

6. Reinstall the gear cover.

NOTICE: For a 2S Li-Po battery, use the included 16T Pinion gear. For a 3S Li-Po battery,

use the optional 14T (Mod 1) pinion gear (LOSA3574).

NOTICE: If you use the 16T (Mod 1) pinion gear with a 3S Li-Po battery, damage to the

vehicle, ESC, and/or motor will occur.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels

do not rotate

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Steering does not work Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Servo gears or motor damaged Replace or repair servo

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

ESC gets hot Motor over-geared Use smaller pinion or larger spur gear

Driveline bound up Check wheels and transmission for binding

Poor run time and/or sluggish

acceleration

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Poor range and/or glitching Transmitter batteries low Check and replace

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

8TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased

(the “Product”) will be free from defects in materials and workmanship at the date of

purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due

to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,

installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv)

attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable

technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon

will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be

defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase

is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,

REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be

assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals). This

warranty gives you speciﬁc legal rights, and you may also have other rights which vary from

state to state. Horizon reserves the right to change or modify this warranty at any time without

notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.

Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live

and use the Product in, please use the Horizon Online Service Request submission process

found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping without additional

protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.horizonhobby.com/content/_service-

center_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included

items, and a brief summary of the problem.A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and RMA number are clearly

written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without notiﬁcation or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁcation. Service estimates are

available upon request.You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as

Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of

use and ownership. If received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging return shipment of

the un-serviced Product, through a carrier of the sender’s choice and at the

sender’s expense. Horizon will hold non-compliant Product for a period of 60

days from notiﬁcation, after which it will be discarded.

10/15

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

10 TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Country of Purchase Horizon Hobby Contact Information Address

United States of America Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/ 4105 Filedstone Rd.

Champaign, Illinois 61822 USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales websales@horizonhobby.com

800-338-4639

United Kingdom Service/Parts/Sales:

Horizon Hobby Limited

sales@horizonhobby.co.uk

+44 (0) 1279 641 097

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS, United Kingdom

Germany Horizon Technischer Service service@horizonhobby.de

+49 (0) 4121 2655 100

Christian-Junge-Straße 1

25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH

France Service/Parts/Sales:

Horizon Hobby SAS

infofrance@horizonhobby.com

+33 (0) 1 60 18 34 90

11 Rue Georges Charpak

77127 Lieusaint, France

Warranty and Service Contact Information

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This product contains a radio transmitter with wireless technology which has been tested and

found to be compliant with the applicable regulations governing a radio transmitter in the

2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your Spektrum

transmitter, please be sure to

maintain a separation distance of

at least 5 cm between your body

(excluding ﬁngers, hands, wrists,

ankles and feet) and the antenna

to meet RF exposure safety re-

quirements as determined by FCC

regulations.

The following illustrations show

the approximate 5 cm RF exposure

area and typical hand placement

when operating your Spektrum transmitter.

IC Information

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product

is in compliance with the essential requirements and other relevant provisions of the

R&TTE and EMC Directive.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a designated

collections point for the recycling of waste electrical and electronic equipment. The separate

collection and recycling of your waste equipment at the time of disposal will help to conserve

natural resources and ensure that it is recycled in a manner that protects human health and

the environment. For more information about where you can drop off your waste equipment for

recycling, please contact your local city ofﬁce, your household waste disposal service or where you

purchased the product.

10 TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

36 TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

36 TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Part # English Deutsch Français Italiano

DYN4955 Fuze 130A Sensorless Bl WP ESC: 4WD SCT 1/8 Fuze 130A Sensorless Bl WP ESC: 4WD SCT 1/8 4WD SCT 1/8 - Contrôleur Brushless Fuze 130A Fuze 130A ESC BL senza sensori WP: 4WD SCT 1/8

DYNS1616 FUZE 550 BL Motor 3800kv FUZE 550 BL Motor 3800kv Moteur Brushless Fuze 550 3800Kv FUZE 550 motore BL 3800kV

LOS230018 Body Set, Painted:TEN MT BK/BLUE Karosserieset lackiert:TEN MT schwarz /blau TEN MT - Carrosserie peinte noire et bleue Set carrozzeria verniciata: TEN MT nero/blu

LOS230019 Body Set, Painted:TEN MT BLACK/GREEN Karosserieset lackiert: TEN MT schwarz /grün TEN MT - Carrosserie peinte noire et verte Set carrozzeria verniciata: TEN MT nero/verde

LOS231015 Front and Rear Shock Towers: TEN MT/SCBE Dämpferbrücke v/h: TEN MT/SCBE TEN MT/SCBE - Supports d'amortisseurs avant

et arrière

Torrette ammortizz. ant./post.: TEN MT/SCBE

LOS231016 Chassis and Brace:TEN MT Chassis und Halter: TEN MT/SCBE TEN MT - Châssis et renfort Telaio e trapezio:TEN MT

LOS231017 Battery Box: TEN MT Akkubox: TEN MT TEN MT - Boitier batterie Scatola batteria: TEN MT

LOS231018 Body Post Set: TEN MT Karosseriehalterset: TEN MT TEN MT - Support de carrosserie Supporti carrozzeria: TEN MT

LOS231019 Radio Tray: TEN MT RC Halterset: TEN MT TEN MT - Platine radio Piastra radio:TEN MT

LOS231020 Wing Mount: TEN MT Flügelhalter: TEN MT TEN MT - Fixation d'aileron Supporto alettone: TEN MT

LOS232015 Wheel Hex w/Pins (4): TEN MT Radmitnehmer m. Stifte (4):TEN MT TEN MT - Hexagones de roues avec goupilles (4) Esagone ruota con perno: TEN MT

LOS232016 Center Diff Mount Set: TEN MT Mitteldiffhalter Set: TEN MT TEN MT - Support de différentiel central Set supporto diff. centrale: TEN MT

LOS232017 Center Dogbone (2): TEN MT Antriebsknochen mitte (2):TEN MT TEN MT - Cardan central (2) Cardano centrale (2):TEN MT

LOS232018 Axle Dogbone (2): TEN MT Antriebsknochen Achse (2):TEN MT TEN MT - Cardan de pont (2) Giunto cardanico (2): TEN MT

LOS233006 Front & Rear Shock Body: TEN MT Dämpfergehäuse: TEN MT TEN MT - Corps d'amortisseur avant et arrière Corpo ammortizzatore ant./post.:TEN MT

LOS233007 Rear Shock Shaft (2): TEN MT Stoßdämpferkolben Set hinten (2):TEN MT TEN MT - Tige d'amortisseur arrière (2) Stelo ammortizzatore posteriore (2): TEN MT

LOS233008 Front Shock Shaft (2): TEN MT Stoßdämpferkolben Set vorne (2): TEN MT TEN MT - Tige d'amortisseur avant (2) Stelo ammortizzatore anteriore (2): TEN MT

LOS233009 Shock Spacer Set: TEN MT Stoßdämpferdistanzstücke Set: TEN MT TEN MT - Entretoise d'amortisseur Set distanziale ammortizz.: TEN MT

LOS233010 Servo Arm Set: Ten MT Losi Servoarmset :Ten MT Ten MT - Set de palonnier de servo Set braccetto servocomando:Ten MT

LOS234010 Suspension Link Set: TEN MT Aufhängungsset: TEN MT TEN MT - Biellettes de suspension Set collegamenti sospensione: TEN MT

LOS235017 5-40 x 1 1/4" BH Screw (8) 5-40 x 1 1/4" BH Schrauben (8) Vis BHC 5-40 x 1 1/4" (8) 5-40 x 1 1/4" viti a testa tonda (8)

LOS235018 Set Screw, M3 X 3mm (10) Madenschraubenset, M3 x 3 (10) Set de vis, M3 x 3mm (10) Vite di arresto, M3 X 3mm (10)

LOS236000 E-Clips 2.5mm (12) E-Clips 2.5mm (12) E-Clips 2,5mm (12) E-clips 2,5mm (12)

LOS236001 3.2mm x 7mm x .5mm Washer (10) 3.2mm x 7mm x .5mm Unterlegscheiben (10) Rondelle 3,2mm x 7mm x 0,5mm (10) Rondella 3,2mm x 7mm x 0,5mm (10)

LOS43010 Wheel and Tire Mounted (2): TEN MT Felge mit Rad montiert (2):TEN MT TEN MT - Pneu et jante montés (2) Cerchione e gomma montati: TEN MT

LOSA3576 1.0 Module Pitch Pinion,16T: 8E,SCTE Losi Ritzel 16Z Modul 1: 8E 8E, SCTE - Pignon module 1.0, 16T Pignone 16T modulo 1.0: 8E,SCTE

LOSA6198 5-40 x 1 7/8" Buttonhead Screw (4) 5-40 x 1 7/8" Halbrundschrauben (4) Vis à tête bombée 5-40 x 1 7/8" (4) 5-40 x 1 7/8" viti a testa tonda (4)

LOSA6240 5-40 x 1/2 Caphead Screw (8) Losi 5-40 x 1/2 Zylinderkopfschrauben (8) Vis CHC 5-40 x 1/2 (8) 5-40 x 1/2 viti a testa a brugola (8)

LOSA6256 4-40 x 1/2 Button Head Cap Screw (6) Losi 4-40 x 1/2 Rundkopfschrauben (6) Vis tête bombée 4-40 x 1/2 (6) 4-40 x 1/2 viti a testa tonda (6)

LOSA6262 8-32 x 1/2" FH Screws (10) Losi 8-32 x 1/2 Flachkopfschrauben (10) Vis FH 8-32 x 1/2" (10) 8-32 x 1/2" viti a testa piatta (10)

LOSA6270 5-40 x 3/8" Flat Head Screws (10) Losi 5-40 x 3/8 Flachkopfschrauben (10) Vis tête plate 5-40 x 3/8" (10) 5-40 x 3/8" viti a testa piatta (10)

LOSA6271 5-40 x 1/2" FH Screws (10) Losi 5-40 x 1/2 Flachkopfschrauben (10) Vis FH 5-40 x 1/2" (10) 5-40 x 1/2" viti a testa piatta (10)

LOSA6272 5-40 x 3/4" FH Screws (10) Losi 5-40 x 3/4 Flachkopfschrauben (10) Vis FH 5-40 x 3/4" (10) 5-40 x 3/4" viti a testa piatta (10)

LOSA6274 5-40 x 1 7/8" FH Screws (2) Losi 5-40 x 1 7/8 Flachkopfschrauben (2) Vis FH 5-40 x 1 7/8" (2) 5-40 x 1 7/8" viti a testa piatta (2)

LOSA6275 5-40 X 5/8" Flat Head Screws (10) Losi 5-40 X 5/8 Flachkopfschrauben (10) Vis tête plate 5-40 X 5/8" (10) 5-40 X 5/8" viti a testa piatta (10)

LOSA6277 5-40 x 3/8" BH Screws (8) 5-40 x 3/8" Rundkopfschrauben (8) Vis BH 5-40 x 3/8" (8) 5-40 x 3/8" viti a testa tonda (8)

LOSA6278 5-40 x 1/2" BH Screws (8) Losi 5-40 x 1/2 Rundkopfschrauben (8) Vis BH 5-40 x 1/2 (8) 5-40 x 1/2" viti a testa tonda (8)

LOSA6279 40 x 3/4" BH Screws (8) Losi 5-40 x 3/4 Rundkopfschrauben (8) Vis BH 40 x 3/4" (8) 40 x 3/4" viti a testa tonda (8)

LOSA6280 5-40 x 1" BH Screws (4) Losi 5-40 x 1 Rundkopfschrauben (4) Vis BH 5-40 x 1" (4) 5-40 x 1" viti a testa tonda (4)

LOSA6282 5-40 x 7/8" BH Screws Losi 5-40 x 7/8 Rundkopfschrauben Vis BH 5-40 x 7/8" 5-40 x 7/8" viti a testa tonda

LOSA6286 5-40 x 5/8 BH Screws (8) Losi 5-40 x 5/8 RundkopfSchrauben (8) Vis BH 5-40 x 5/8 (8) 5-40 x 5/8 viti a testa tonda (8)

LOSA6290 8-32 x 1/2 BH Screws (8) Losi 8-32 x 1/2 Rundkopfschrauben (8) Vis BH 8-32 x 1/2 (8) 8-32 x 1/2 viti a testa tonda (8)

LOSA6302 5-40 Locking Nuts, Steel Losi Stoppmmuter 5-40 Stahl (4) Nylstop, acier 5-40 5-40 dado autobloccante, acciaio

LOSA6306 4-40 Aluminum Mini-Nuts (10) Losi 4-40 Aluminium Mini-Muttern (10) Mini écrous en aluminium 4-40 (10) 4-40 mini dadi alluminio (10)

LOSA6350 #4 and 1/8" Hardened Washers Losi Unterlegscheiben #4 und 1/8 gehärtet Rondelles durcies #4 et 1/8" #4 and 1/8" rondelle

LOSA6947 5x11x4 Rubber Sealed Ball Bearing (4) Losi 5x11x4 Kugellager gekapselt (4) Roulements étanches 5x11x4 (4) 5x11x4 cuscinetti a sfera sigillati in gomma (4)

LOSA6956 12 x 18 x 4mm Ball Bearing (2) 12 x 18 x 4mm Kugellager (2) Roulement à bille12 x 18 x 4mm (2) 12 x 18 x 4mm cuscinetto a sfera (2)

LOSA6957 10x15x4 mm BB (2) with Nylon Retainer 10x15x4 mm Kugellager (2) mit Bundrand Roulements 10x15x4 ﬂasques nylon (2) 10x15x4 mm cuscinetti (2) con fermo in nylon

LOSA6958 6x12x4 mm BB (2) with Nylon Retainer 6 x 12 x 4 BB mm Kugellager (2) mit Bundrand Roulements 6x12x4 ﬂasques nylon (2) 6x12x4 mm cuscinetti (2) con fermo in nylon

LOSB2021 Front Suspension Arm Set: 10-T Querlenkerset vorne: 10-T 10-T - Set de triangles avant Set braccetto sospensione anteriore: 10-T

LOSB2022 Rear Suspension Mount Cover: TEN-SCTE Querlenkerabdeckung hinten: TEN-SCTE TEN SCTE - Couvercle support suspension arrière Copertura supporto sospensione post.:TEN-SCTE

LOSB2023 Rear Suspension Arm Set: 10-T Querlenkerset hinten: 10T 10-T - Set de triangles Arr Set braccetto sospensione posteriore: 10-T

LOSB2100 Front Spindle & Carrier Set: 10-T Achsschenkel und Achsschenkelträger: 10-T 10-T - Set fusées et étriers avant Set fusello e portafusello anteriore: 10-T

LOSB2103 Rear Hub & Spacer Set: 10-T Hintere Aufhängung: 10-T 10-T - Fusées arrières et entretoises Set hub posteriore con rondelle: 10-T

LOSB2123 Steering Bellcrank Set: 10-T Servosaver Set: 10-T 10-T - Parties plastiques de sauve servo Set squadrette sterzo: 10-T

LOSB2124 Steering Posts/Tubes & Hardware: 10-T Stehbolzen für Servosaver: 10-T 10-T - Support, tubes et accessoires de direction Set comandi sterzo e hardware: 10-T

LOSB2211 Fr/R Pin Mount Cover Set: 10-T Abdeckung f. Querlenkerhalter: 10-T 10-T - Set de protections de supports de pivots Set copertura montante perno ant./post.: 10-T

LOSB2213 Pivot Pin Mount Set, Steel (4): 10-T Querlenkerhalter Set (4) Stahl: 10-T 10-T - Supports de pivots en acier Set montante perno girevole, acciaio: 10-T

LOSB2222 Front/Rear Sway Bar Kit: 10-T Querstabilisatorset v/h: 10-T 10-T - Barre antis roulis av./arr Kit barra antitorsione ant./post.: 10-T

LOSB2279 Steering Drag Link & Hardware: 10-T Lenkgestänge und Zubehör: 10-T 10-T - Barre d'ackerman et accessoires Rinvio trascinamento sterzo e hardware: 10-T

LOSB2904 Shock Plastics Set (4): 10-T Kunststoffteile Stoßdämpfer (4): 10-T 10-T - Set pièces plastiques d'amortisseurs (4) Set parti in plastica ammortizz. (4): 10-T

LOSB2905 Fr/R Shock Boots (8): 10-T Stoßdämpfermanschetten (8):10-T 10-T - Chaussettes de protection de tiges

d'amortisseurs (8)

Protezione stelo ammortizzatore ant./post. (8): 10-T

LOSB2906 Shock Rebuild Set (2): 10-T Stoßdämpfer Reparatur Set (2):10-T 10-T - Kit de réparation d'amortisseur (2) Set riparazione ammortizz. (2): 10-T

LOSB2909 Piston Pack (2): TEN-T/TEN-SCTE Stoßdämpferkolben: TEN-SCTE TEN-T/TEN-SCTE - Pack de piston (2) Pistoni (2): TEN-T/TEN-SCTE

LOSB2963 Rear Racing Spring Set: TEN LOSI Rennfedernsatz hinten: TEN Set de ressorts arrière de compétition - TEN Set molle racing posteriori:TEN

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI 37

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

Part # English Deutsch Français Italiano

DYNC2010CA Prophet Sport Plus 50W AC/DC Charger Dynamite Prophet Sport Plus 50W Gleich- und

Wechselstrom-Ladegerät

Chargeur Prophet Sport Plus 50W AC/DC Prophet Sport Plus 50W AC/DC caricabatteria

LOS230017 Body Set, Clear: TEN MT Karosserieset transparent:TEN MT TEN MT - Carrosserie transparente Set carrozzeria trasparente:TEN MT

LOSB2130 Rear Hubs, Aluminum: TEN Losi Radträger hinten, Aluminium: TEN TEN - Fusées arrière en aluminium Mozzi posteriori, alluminio:TEN

LOSB2825 Front Shock Body (2): 10-T Dämpfergehäuse vorne: 10-T 10-T - Corps d'amortisseurs avant (2) Set corpo ammortizzatore ant. (2): 10-T

LOSB2826 Rear Shock Body (2): 10-T Dämpfergehäuse hinten: 10-T 10-T - Corps d'amortisseurs arrière (2) Set corpo ammortizzatore post. (2): 10-T

LOSB2845 Fr/R Shock Shaft Set (4): 10-T Stoßdämpferkolbenstange v/h (4): 10-T 10-T - Set de Tiges d'amortisseurs avant et arrière (4) Set stelo ammortizzatore ant./post. (4): 10-T

LOSB2959 Front Racing Spring Set: TEN Federnsatz Racing vorne:TEN TEN -Set de ressorts avant de compétition Set molle racing ant.: TEN

LOSB2963 Rear Racing Spring Set:TEN Federnsatz Racing hinten: TEN TEN -Set de ressorts arrière de compétition Set molle racing post.:TEN

LOSB3575 Front/Rear HD Lightened Outdrive Set (2): TEN Antriebsklauenset v/h HD extra leicht: (2):TEN TEN -Noix de cardans av/arr renforcées allégées (2) Set trascinatori ant./post. HD (2): TEN

LOSB3576 Center HD Lightened Outdrives (2):TEN Antriebsklauenset mitte HD extra leicht: (2):TEN TEN -Noix de cardans centrales renforcées

allégées (2)

Set trascinatori centrali HD (2):TEN

LOSB4003 Front/Rear Steering Turnbuckle Set (6): 10-T

(Requires LOSB4023)

Gewindestifte Lenkung (6): 10T

(erfordert LOSB4023)

10-T - Biellettes de direction avant et arrière (6)

(nécessite LOSB4023)

Set tiranti ﬁlettati ant./post.(6): 10-T

(necessita LOSB4023)

LOSB4023 Rod End Set: 10-T (Requires LOSB4003) Losi Kugelpfannen Set (erfordert LOSB4003): 10-T 10-T - Set de Chapes (20) (nécessite LOSB4003) Set tiranti: 10-T (necessita LOSB4003)

LOSB4112 Adjustable Front Hinge Pin Holder Set: TEN Losi Querlenkerhalterset vorne einstellbar,

Aluminium: TEN

TEN - Support d’axes de suspension avant réglable Set piastrine regolabili anteriori:TEN

LOSB4113 Adjustable Rear Hinge Pin Holder Set:TEN Losi Querlenkerhalterset hinten einstellbar,

Aluminium: TEN

TEN - Support d’axes de suspension arrière réglable Set piastrine regolabili posteriori: TEN

LOSB7013 320S Force Wheel, Chrome (2) Losi 320S Force Wheel/ Chrome (2) Jante 320S Force Chrome (2) 320S cerchione force, cromo (2)

SPMS601H Extra High Torque Servo Extra High Torque Servo Servo couple très élevé Servocomando extra high torque

TLR233020 Front Spring Set, Hard (3 pair): 22T/SCT, SCTE TLR Stoßdämpferfedernset vorne, hart (3 paar):

22 T/SCT, SCTE

22T/SCT, SCTE - Ressorts d'amortisseurs avant,

durs (3 paires)

Set molle anteriori, dure (3 paia): 22T/SCT, SCTE

TLR234001 Carbon Front Tower: SCTE 2.0

(Requires LOS234009)

TLR SCTE 2.0: Dämpferbrücke vorne Carbon

(erfordert LOS234009)

SCTE 2.0 - Support d'amortisseurs avant en

carbone (nécessite LOS234009)

Torretta ant. in carbonio: SCTE 2.0

(necessita LOS234009)

TLR234002 Carbon Rear Tower: SCTE 2.0

(Requires LOS234009)

TLR SCTE 2.0 : Dämpferbrücke hinten Carbon

(erfordert LOS234009)

SCTE 2.0 - Support d'amortisseurs arrière en

carbone (nécessite LOS234009)

Torretta post. in carbonio: SCTE 2.0

(necessita LOS234009)

TLR234039 Hinge Pin Set,TiCN (6): SCTE TLR Scharnierbolzen Set, TiCN (6): SCTE SCTE - Set d'axes de suspension Ti-Cn (6) Set perni braccetti, TiCN (6): SCTE

TLR234040 Front Shock Shaft, TiCN (2): SCTE TLR Kolbenstange vorne, TiCN (2): SCTE SCTE - Axes de triangles avant Ti-Cn (2) Stelo ammortizzatore ant., TiCN (2): SCTE

TLR234041 Rear Shock Shaft,TiCN (2): SCTE TLR Kolbenstange hinten, TiCN (2): SCTE SCTE - Axes de triangles arrière Ti-Cn (2) Stelo ammortizzatore post., TiCN (2): SCTE

TLR334017 Ft Spindle Carrier, 15 Deg, +2mm,Alum: SCTE TLR SCTE Radträger 15° + 2mm, Alu SCTE - Étrier porte fusée, 15°, +2mm en

aluminium

Portafusello ant., 15°, +2mm, allu.: SCTE

TLR5062 Bleeder Shock Caps,Aluminum (2): TEN TLR TEN: Stoßdämpferendkappe Aluminium (2) TEN - Bouchons d'amortisseurs à purgeurs en

aluminium (2)

Tappi ammortizzatore con vite di spurgo, allu.

(2): TEN

TLR99004 TLR Embroidered Cargo Bag TLR Tasche Sac de transport TLR brodé Borsone TLR

TLR99014 TLR Foam Pit Mat TLR Schraubermatte Schaum Tapis de stand en mousse TLR TLR Foam Pit Mat

Optional Parts // Optionale Teile // Pièces Optionnelles // Parti Opzionali

LOSB3104 Front/Rear Gearbox Set: 10-T Diffgehäuse v/h Set: 10-T 10-T - Carter de transmission avant et arrière Set cellula ant./post.: 10-T

LOSB3436 40T Spur Gear, Mod 1:TEN-SCTE Zahnrad 40Z M1: TEN-SCTE TEN-SCTE - Couronne 40T, Mod 1 40T corona, Mod 1: TEN-SCTE

LOSB3553 Center Diff Outdrive Set (2): 10-T Diff Gehäuse u Dichtung Set : 10-T 10-T - Noix de cardan de diff central (2) Set trascinatore diff. centrale (2): 10-T

LOSB3563 Fr/R Diff Outdrive Set (2): 10-T Antriebswelle Vorne/hinten inkl. Zubehör: 10-T 10-T - Noix de cardan de sortie de diff avant et

arrière (2)

Set trascinatore diff. ant./post. (2): 10-T

LOSB3564 Fr/R Driveshafts (2): 10-T Antriebswelle v/h (2): 10-T 10-T - Arbres de cardans av ou arr (2) Albero trasmissione ant./post. (2): 10-T

LOSB3565 Fr/R CV Couplers (4): 10-T CV Kuppungsstücke v/h: 10-T 10-T - Coupleurs de cardans avant ou arr CVD (4) Accoppiatori CV ant./post. (4): 10-T

LOSB3566 Fr/R Axles (2): 10-T Losi Achsen vorne / hinten (2): 10-T 10-T - Pont av./arr. (2) Assi ant./post. (2): 10-T

LOSB3568 Diff Gasket & Misc: 10-T Vergaserdichtung + div: 10-T 10-T - Set de joints et goupilles de diff Giunta diff. & hardware: 10-T

LOSB3569 Diff Gear Set w/Hardware: 10-T Zahnräderset Differential m Zbh.: 10-T 10-T - Pignons de différentiels avec accessoires Ingranaggio diff. & hardware: 10-T

LOSB3571 Fr Ring & Pinion Gear Set: 10-T Stirnrad vorne & Ritzelset: 10-T 10-T - Pignon conique d'attaque et couronne

conique avant

Anello ant. & set pignoni: 10-T

LOSB3572 Rear Ring & Pinion Gear Set: 10-T Stirnrad hinten & Ritzelset: 10-T 10-T - Pignon conique d'attaque et couronne

conique arrière

Anello post. & set pignoni: 10-T

LOSB3590 Differential Gear Grease: TEN Differentialfett: TEN TEN -Graisse pour pignons de différentiel Grasso ingranaggio diff.: TEN

LOSB3591 Differential Screws (8): TEN Differentialschrauben (8): TEN TEN - Vis de différentiel (8) Viti differenziale (8): TEN

LOSB4022 Camber & Steering Ball Set (12): 10-T Kugelkopfset Lenkung & Spur (12): 10-T 10-T - Set de rotules de carrossage et direction (12) Camber & set sfere sterzo (12): 10-T

LOSB4109 Suspension Hinge & King Pin Set (10): 10-T Querlenkerstift (10): 10-T 10-T - Set d'axes de suspensions et d'axes de fusées (10) Braccetto sospensione & set king pin (10): 10-T

LOSB8154 Rear Wing & Hardware: 10-T 10-T Hinterer Flügel mit Zubehör Aileron arrière et visserie Alettone posteriore & hardware: 10-T

SPM2330 DX2E 2Ch DSMR Surface Radio w/SR310 DX2E 2Ch DSMR Surface Radio mit SR310 Émetteur DX2E 2 voies DSMR avec RX SR310 DX2E trasmittente DSMR a due canali con SR310

SPMSRS4201 Replacement Rx: SRS4201 DSMR AVC Ausstauschempfänger Rx: SRS4201 DSMR AVC Récepteur SRS4201 DSMR AVC de remplacement Ricevente di ricambio: SRS4201 DSMR AVC

TLR8202 Body Clips, Black (12): 22 Body Clips, schwarz (12): 22 22 - Clips de carrosserie noirs (12) Clip carrozzeria, neri (12): 22

TLR237000 5x8x2.5mm Bearings (2) 5x8x2.5mm Kugellager (2) Roulements 5x8x2,5mm (2) 5x8x2.5mm cuscinetti (2)

TLR245002 5-40 x 1/4" BH Screws (10) TLR 5-40 x 1/4'' BH Schrauben (10) Vis BH 5-40 x 1/4" (10) 5-40 x 1/4" viti a testa tonda (10)

TLR332001 HD Diff Housing, Integrated Insert:TEN TLR TEN : HD Diff Gehäuse TEN -Carter de différentiel renforcé, insert intégré Alloggiamento diff. HD, con inserti: TEN

TLR332051 Coupler Outdrive: SCTE 2.0 TLR Kupplungsstück für Antriebsklaue: SCTE 2.0 SCTE 2.0 - Noix de cardan Accoppiatore trascinatore: SCTE 2.0

TLR334000 O-Rings, Bleeder Shock Cap (8): TEN TLR O-Rings / Dämpferkappe mit Entlüftung (8):TEN TEN -Joints toriques de bouchons d'amortisseurs

à purge (8)

O-ring, tappo ammortizzatore con vite di spurgo

(8): TEN

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

38 TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

Exploded View // Explosionszeichnung // Vue éclatée des pièces // Vista esplosa delle parti

38 TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

LOSB8154

TLR8202

LOSB8154

TLR8202

Clear/Transparent/Transparente/Trasparente = LOS230017

Blue/Blau/Bleu/Blu = LOS230018

Green/Grün/Vert/Verde = LOS230019

LOS231020

LOSA6278

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI 39

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

TLR8202

SPMSRS4201

LOS231019

LOSA6350

SPMS605

LOS231019

LOSA6256

LOSA6350

LOSA6270

DYN4955

LOSA6262

LOS232017

LOSA6350

LOSA6262

LOS231016 LOS235017

LOS231017

LOS231016

LOS233010

LOSB2279

TLR237000

LOSB2124

LOSB2123

LOSA6350

TLR237000

LOSA6270

LOSA6277

LOSB2123

LOSB2124

LOSB2124 TLR237000

LOSB2123

LOSA6306

LOSA6275

LOSB4022

LOSA6275

LOSB4022

LOS234010 LOSA6256

LOSB4022

LOSA6256

LOSB4022

LOSA6277

CHASSIS EXPLODED VIEW

CHASSIS EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE DU CHÂSSIS

VISTA ESPLOSA DEL TELAIO

40 TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

LOS232017

LOSB3553

LOSA6270

LOS232016

LOSA6956

TLR332001

DYNS1616

TLR332001

TLR245002

LOS232016

LOSB3553

LOSB3436

LOSB3568

LOSA3576

LOSA6956

TLR332001

LOSB3570

LOSB3569

TLR332001

LOSB3569

LOSA6240

40 TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

REAR EXPLODED VIEW

HECK EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE ARRIÈRE

VISTA ESPLOSA DELLA PARTE POSTERIORE

REAR SHOCKS / STOSSDÄMPFER H

AMORTISSEURS ARR / AMMORTIZZATORI POSTERIORE

LOSB2904

LOSB2963

LOS233007

LOSB2906

LOSB2904

LOS233009

LOS233006

LOSB2904

LOSB2906

LOS233006

LOSB2904

LOSB2187

LOSB2963

LOS233008

LOSB2904

LOS233009

LOSB2906

LOSA6958

LOS234010

LOSA6286

LOS232015

LOSB3566

LOSB2103

LOSA6957

LOS231018

LOSB3564

LOSB3565

LOSB2023

LOSB3563

LOSA6274

LOSB2213

LOSB2022

LOSB4109

LOSA6302

LOSB4109

LOSA6302

LOSA6271

LOSB2103

LOSB3104

LOSB2211

LOSB2213

LOSA6282

LOSA6302

LOSB4022

LOSA6302

LOS231015

LOSA6280

LOSA6256

LOSB2906

LOSA6256

LOSA6279

LOSA6256

LOSB2906

TEN-MT RTR, AVC: 1:10 4WD • MANUALE DI ISTRUZIONI

FRONT EXPLODED VIEW

FRONT EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE AVANT

VISTA ESPLOSA DELLA PARTE ANTERIORE

LOSB2021

LOSB3564

LOSB2021

LOSA6290

LOSB2100

LOSB4109

LOSA6957

LOSA6958

LOS232015

LOSB3566

LOSB2100

LOSB3563

LOSA6286

LOS234010

LOSA6302

LOSA6272

LOSB4022

LOSA6302

LOSB4022

LOSA6282

LOSB4022

LOS232015

LOSB2100

LOSB3571

TLR332051

LOSA6947

LOSA6275

LOSB2211

LOSB2213

LOSB3104

LOSA6280

LOSB2906

LOS231015

LOSB3104

LOSB2211

LOSB2213

LOSA6275

LOS231015

LOSB4109

LOSB4109 LOSA6956

TLR332001

LOSA6956

LOSB3571

TLR332001

LOSB3569

LOSB3568

LOSA6256

LOSA6279

LOSA6256

LOS43010

LOSB3566

LOS43010

TEN-MT RTR, AVC: 1:10 4WD • INSTRUCTION MANUAL

LOSB2904

LOSB2963

LOS233007

LOSB2906

LOSB2904

LOS233009

LOS233006

LOSB2904

LOSB2906

LOS233006

LOSB2904

LOSB2187

LOSB2963

LOS233008

LOSB2904

LOS233009

LOSB2906

FRONT SHOCKS / STOSSDÄMPFER V

AMORTISSEURS AVANT / AMMORTIZZATORI ANTERIORE

Losi, DSM, DSM2, DSMR, AVC, Active Vehicle Control, EC3, Dynamite, Fuze, Prophet and the Horizon Hobby logo are trademarks or

registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Patents pending.

Updated 09/16 49177.1 LOS03006 T1/T2

WWW.LOSI.COM

Table of contents

Team Losi TEN MT User manual