TECHNIMOUNT EMS TECHNI-IV POLE Original operating instructions

TECHNI-IV POLE
Quick Installation
EMS
TM
© 2023 Technimount E.M.S. Holding Inc. QI-TIVP-202305EN-01 | Page 1 of 5
Intended Use
This procedure is used to help EMS personnel effectively
install the Techni-IV Pole and its strap on a Technimount
Xtension Pro™ Assistant CCT/ECMO mobile structure.
Product and medical device manufacturer names
are Trademarks™ or Registered Trademarks®of their
respective holders.
Image references within this document may differ from
actual product. For more information or to ensure product
options and availability, please contact Technical Support
at techsuppor[email protected].
Technimount E.M.S. Holding Inc.
C/O: Regulatory Affairs
3770 Jean Marchand Street, Suite 100-C
Quebec (QC) G2C 1Y6
Canada
www.technimount.com
T + 1 581.700.6613
TF + 1 888.639.2758 (North America)
Unpack the Techni-IV Pole
1. Inspect the shipping box(es) for signs of damages, before accepting shipment. Take pictures and report
them promptly if applicable.
2. Move the shipping box(es) to the location of the installation.
3. Open the shipping box(es).
4. Unpack the box(es) and ensure that all shipping and packaging materials have been properly removed,
prior to installation.
NOTE: Keep all packaging material for future use.
5. Identify all the components and hardware included for the installation, then set aside. Refer to the "Safety
Measures" section for details.
6. Inspect the items for signs of damages. Take pictures and report them promptly if applicable.

TECHNI-IV POLE
Quick Installation
EMS
TM
© 2023 Technimount E.M.S. Holding Inc. QI-TIVP-202305EN-01 | Page 2 of 5
Safety Measures
WARNING -Part Breakage
Do not use powered tools to screw the hardware during installation, as there is a potential risk of
damage to the threads.
WARNING -Risk of Injury
Regulations and standards for safety are the sole responsibility of the end user. Ensure that the
installation specifications meet the local and regional compliance requirements before use. Product
incompatibility could cause unpredictable functioning resulting in injury to the patients or EMS
personnel.
CAUTION -Safe Handling and Operation
-Do not modify the product, or any of its components and use only as per described in this
document. Modifying the product or improper use could cause unpredictable functioning, resulting
in injury to the patients or EMS personnel.
-The end user and administrator are responsible for providing proper training to any personnel
susceptible of contact with the product prior to use. Installation, operation, and maintenance should
only be performed by trained personnel.
-Improper use of the Technimount product may damage the device or cause injury to the patients or
EMS personnel.
CAUTION -Working Load/Load Balance
The Techni-IV Pole is approved for ambulance transport. The maximum weight capacity approved for
transport is 1.5 L or 1.5 kg (50 fl oz or 3.3 lbs).
CAUTION -Follow Instructions for Use
-Always read and abide by all the safety guidelines identified, as well as follow instructions provided
within this document.
-Refer to the stretcher’s user manual for safety precautions and user instructions for the safe use of
the Stryker Power-PRO™ XT stretcher.
Required Tools
-Philips screwdriver, #2
-Key, 7/16 in.

TECHNI-IV POLE
Quick Installation
EMS
TM
© 2023 Technimount E.M.S. Holding Inc. QI-TIVP-202305EN-01 | Page 3 of 5
Stretcher Orientation and Techni-IV Pole Position
Patient head end
Patient right
Patient left
Patient foot end
Figure 1: Stretcher orientation and Techni-IV Pole position (patient left shown here)
Required Parts
1
3
2
4
5
1. Techni-IV Pole
2. Strap
3. Flat head Philips drive screws
¼ - 20 X 1 in. (2X)
4. Washers (2X)
5. Nylon-insert locknuts ¼ - 20
(2X)
Figure 2: Techni-IV Pole parts

TECHNI-IV POLE
Quick Installation
EMS
TM
© 2023 Technimount E.M.S. Holding Inc. QI-TIVP-202305EN-01 | Page 4 of 5
Install the Techni-IV Pole
1. Locate the two (2) holes on the mobile structure top plate intended for the installation of the
Techni-IV Pole (Figure 3 A).
2. Place the Techni-IV Pole on the mobile structure top plate aligning the screw holes, then insert the two (2)
screws (Figure 3 B).
3. From under the mobile structure top plate, insert a washer and locknut on each screw, then tighten the
screws while holding the locknuts using a key 7/16 in. and Philips screwdriver #2 (Figure 3 B).
(A) (B)
Figure 3: Techni-IV Pole installation on the mobile structure top plate
4. Insert the center loop of the strap on the Techni-IV Pole (Figure 4 A).
5. Hook the eyelet at the end of the strap into one of hooks located at the top of the Techni-IV Pole to install
(Figure 4 B).
(A) (B)
Figure 4: Strap installation

TECHNI-IV POLE
Quick Installation
EMS
TM
© 2023 Technimount E.M.S. Holding Inc. QI-TIVP-202305EN-01 | Page 5 of 5
6. Use the strap buckles to adjust the size of the strap on the Techni-IV Pole, depending on the size of the IV
bags used.
The installation of the Techni-IV Pole and its strap on the Xtension Pro™ Assistant CCT/ECMO mobile structure is
complete (Figure 5).
Figure 5: Techni-IV Pole installed on the Xtension Pro™ Assistant CCT/ECMO mobile structure