TechOne Hobby FPV Kraftei 650 EPO User manual

FPV Kraftei 650EPO

CG Position:150-160mm away from fuselage nose.
Item no.: 0880007FPV
1.EPO foam construction that is beautiful, crash-resistant and easy for maintenance.
2. Use T-Motor AIR40 motor, the flying speed can reach 200km/h,it also have very stable
flying performance at high speed and low speed.
3. Removable Motor bring the easy assembly without screw,it's very convenient for you.
4. FPV equipment can be installed easily on Independent platform.
Wingspan
Fuselage
Flying weight
Motor
ESC
Servo
Battery
Propeller
Camera
image transmission
Mounted Equipment
Flying control
702mm(28in)
470mm(18.5in)
280-300g(with battery)
AS2212-10 KV2280
30-40A
9g*2 pcs
3S 1800-2200mAh
5*5
702mm(28in)
490mm(19.3in)
385-400g(with battery)
AIR40 KV2450
F30A 2-4S
11g*2 pcs
4S 1300-1500mAh
5045
RunCam、Foxeer Arrow、FOXEER
FX 200MW-600MW
HawKeye Firefly Q6、RunCam HD 1080P、gopro 3-5
F4 F3
Kraftei 650 FPV Kraftei 650
/
/
/
/
FPV Kraftei 650

1.Lower wing + Upper Fuselage 1PC 3. Equipment Canopy 1PC
2.Rudder 1PC 4. FPV equipment platform 1PC
The following 1-4 are the common installation steps of the Kraftei version and the FPV Kraftei version.
1.Put the rudder into the corresponding slot of plane
0
body, make sure A=90 , then glue it well.
2. Put the servo horn into the corresponding slot of
aileron, fix it with screw.
3. Fix the servo arm on servo with screw, put the servo
and servo wire into the corresponding slot as picture,
then fix the servo with glue（solid gum)
4. Cross the Z head of pushrod on servo arm, then
install another head on the servo horn with clip.
The Following 5-11 are the installation steps of Kraftei version
5. Put the motor mount A into the corresponding slot of
plane body, then fix it with glue.
6. Fix the motor on the motor mount A with screw.
7. Fix the 5*5 propeller and spinner on the motor
output shaft with screw.
8. Connect the ESC and motor well, then put it into
the equipment cabin.
9. Insert the servo wire and ESC signal line into the
corresponding slot of receiver, fix the receiver on
the side wall of equipment cabin with 3M double side
tape.
10. Put battery into the equipment cabin, then fix
it with battery velcro.
FPV Kraftei 650

11. Fix the equipment canopy on the equipment cabin
with clip.
The following 12-20 are the installation steps
of FPV Kraftei version.
12. Put the cowl into the corresponding slot of plane
body, then glue it well.
13. Insert the motor mount B into the corresponding
slot, then fix it with glue.
14. Insert the rear screw of motor into the corresponding
big hole of motor mount, then clamp and rotate the
motor with a tool along the direction of arrow, make
sure rotate it in place.
15. Put the ESC into the fuselage and connect with the
motor well.
16. Fix the 5045 propeller on the motor with screw.
17. Insert the servo wire and ESC signal line into the
corresponding slot of receiver, fix the receiver on
the side wall of equipment cabin with 3M double
side tape.
18. Put the battery into the equipment cabin, then fix it
with battery velcro.
20. Fix the FPV equipment platform on the equipment
cabin through clip.
Safety is the first rule for any kind of flying. Third party insurance should be considered as a
basic essential. If you join a model club they usually have an insurance scheme as part of the
membership fee.
It is your personal responsibility to ensure you have adequate insurance. Make it your priority
to keep your models and radio control system in perfect order at all times. Check the correct
charging procedure for the batteries you are using. Make sure of all sensible safety systems
and precautions which are advised for your system.
Always fly with a responsible attitude. Please don’t fly your models dangerously, it is not wise to
fly near people or over their heads. Be SMART, fly SAFE. Always fly in such a way that you do
not endanger yourself or others.
Bear in mind that even the best RC system in the world is subject to outside interference. No
matter how many years of accident free flying you have under your belt, things can go wrong at
any time and in a matter of seconds. We hope you have many hours of pleasure building and
flying your new model.
FPV Kraftei 650
19. Install the camera, image transmission and flying
control on the FPV equipment platform.

FPV Kraftei 650
Spare parts
Wing+Fuselage
Item no.: 0931PJ001
Rudder
Item no. : 0931PJ002
Spinner
Item no. : 088306R
(Just For Kraftei version)
Motor mount A
Item no. : 088305
(Just For Kraftei version)
Motor mount B
Item no. : 0931PJ003
FPV Equipment platform
Item no. : 0931PJ004
Pushrod and control horn
Item no. : 0931PJ005
Accessories
Item no. : 0931PJ006
Motor: AIR40 KV2450
Item no. :1001022
Servo: 11g micro servo
Item no. :1003008A
ESC : F30A 2-4S
Item no. :1002017 Propeller: 5045 SF prop
Item no. :1004019
Motor: AS2212-10 KV2280
Item no. : 1001019
(Just For Kraftei version)
Servo: 9g micro servo
Item no. : 1003005B
(Just For Kraftei version)
ESC : 30Amp
Item no. : 1002005
(Just For Kraftei version)
Propeller: 5*5 SF prop
Item no. : 1004016
(Just For Kraftei version)