Teknik Canal Heights 5419232 User manual

www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Canal Heights TV Stand
5419232
Smart stand
for the idiot box.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-24
25-28
29-32
33-34
35
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
50 lbs.
50 lbs.
19"
19"
41-1/2"
41-1/2"
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G SHELF (2)
H BACK (1)
I RIGHT FRONT PANEL (1)
J LEFT FRONT PANEL (1)
K FRONT CORNER (2)
L RIGHT REAR CORNER (1)
M LEFT REAR CORNER (1)
N RIGHT LEG ASSEMBLY (1)
O LEFT LEG ASSEMBLY (1)
P BRACE (2)
Q BACK BRACE (2)
R SHELF BRACE (2)
S DRAWER FRONT (1)
T DRAWER BACK (1)
U RIGHT DRAWER SIDE (1)
V LEFT DRAWER SIDE (1)
W DRAWER BOTTOM (1)
X DRAWER BRACE (1)
Page 3
A
B
C
D
E
F
G
H
W
K
L
N
O
P
Q
R
S
TU
V
G
I
J
K
M
P
Q
R

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
EXTENSION SETS SHOWN SEPARATED
1/2" MACHINE SCREW - 20
16
HIDDEN CAM - 25
3CAM SCREW - 25 4
1-1/2" FLAT HEAD SCREW - 13
12
EXTENSION SLIDE - 2
2
EXTENSION RAIL - 2
1
CAM COVER - 2
10
KNOB - 1
9
1-3/8" MACHINE SCREW - 10
13
3/4" MACHINE SCREW - 2
15
1/2" PAN HEAD SCREW - 12
17
SMALL HIDDEN
CAM - 4
5SMALL CAM
SCREW - 4
6
1-1/4" FLAT HEAD SCREW - 16
14
WOOD DOWEL - 40
7SMALL WOOD
DOWEL - 2
8
WARNING LABEL - 1
18
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
(Refer to the last step for proper
location and application)

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert thirteen CAM SCREWS (4) into the TOP (E).
Page 5
E
4
(13 used)

Step 2
Page 6
å Separate the EXTENSION SLIDES (2) from the
EXTENSION RAILS (1) as shown in the right enlarged
diagram. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the UPRIGHTS (C
and D). Use six 1/2" PAN HEAD SCREWS (17).
å NOTE: Use the exact holes shown in the RAILS.
å Insert sixteen WOOD DOWELS (7) into
the exact holes shown in the ENDS (A and B)
and UPRIGHTS (C and D).
C
BA
D
Open end
Open end
21
1
1
Mounting holes
Open end
7
(16 used)
1/2" PAN HEAD SCREW
(6 used in this step)
17
1

Step 3
419232
å Turn six CAM SCREWS (4) into the exact holes shown in
the REAR CORNERS (L and M) and BACK (H).
å Insert ten WOOD DOWELS (7) into the exact holes shown
in the REAR CORNERS (L and M) and BACK (H).
4
(6 used)
7
(10 used)
H
L
M

Step 4
Page 8
3
21
3
The arrow must
point toward the
edge of the board.
H
L
M
å Insert two HIDDEN CAMS (3) into the BACK (H).
å Fasten the REAR CORNERS (L and M) to the BACK (H).
Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the edges of the
BACK insert into the holes in the REAR CORNERS.
3
3

Step 5
Page 9
å Turn six CAM SCREWS (4) into the exact holes shown in the
FRONT PANELS (I and J) and FRONT CORNERS (K).
å Insert fourteen WOOD DOWELS (7) into the exact holes shown
in the FRONT PANELS (I and J) and FRONT CORNERS (K).
4
(6 used)
7
(14 used)
K
K
J
I

Step 6
419232
å Insert two HIDDEN CAMS (3) into the FRONT PANELS (I and J).
å Fasten the FRONT CORNERS (K) to the FRONT PANELS (I and J).
Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the edges of the FRONT
PANELS insert into the holes in the FRONT CORNERS.
3
3
K
K
J
I

Step 7
Page 11
K
K
J
I
B
D
A
C
å Insert four HIDDEN CAMS (3) into the ENDS (A and B)
and UPRIGHTS (C and D).
å Fasten the ENDS (A and B) and UPRIGHTS (C and D) to
the FRONT PANELS (I and J) and FRONT CORNERS (K).
Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the edges of the
ENDS and UPRIGHTS insert into the holes in the FRONT
PANELS and FRONT CORNERS.
3
(4 used)

Step 8
Page 12
B
D
A
C
H
J
I
å Insert four HIDDEN CAMS (3) into the ENDS (A and B)
and UPRIGHTS (C and D).
å Fasten the ENDS (A and B) and UPRIGHTS (C and D) to
the BACK (H) and REAR CORNERS (L and M). Tighten
four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the edges of the
ENDS and UPRIGHTS insert into the holes in the BACK
and REAR CORNERS.
M
L
3
(4 used)

Step 9
Page 13
å NOTE: You may need someone's help in this step.
å Insert thirteen HIDDEN CAMS (3) into the ENDS (A and B),
UPRIGHTS (C and D), BACK (H), and FRONT PANELS (I
and J).
å Fasten the ENDS (A and B), UPRIGHTS (C and D), BACK (H),
and FRONT PANELS (I and J) to the TOP (E). Tighten thirteen
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the edges of the
ENDS, UPRIGHTS, BACK, FRONT PANELS, and CORNERS
insert into the holes in the TOP.
B
D
A
C
H
J
I
M
L
E
K
K
3
(13 used)

Step 10
Page 14
å Fasten the BOTTOM (F) to the ENDS (A and B),
UPRIGHTS (C and D), BACK (H), and FRONT PANELS (I
and J). Use thirteen 1-1/2" FLAT HEAD SCREWS (12).
å NOTE: Be sure the WOOD DOWELS in the edges of
the ENDS, UPRIGHTS, BACK, FRONT PANELS, and
CORNERS insert into the holes in the BOTTOM.
B
D
A
C
H
J
I
M
L
K
K
F
1-1/2" FLAT HEAD SCREW
(13 used in this step)
12

Step 11
Page 15
R
R
P
P
O
N
å Fasten the BRACES (P and R) to the LEG
ASSEMBLIES (N and O). Use sixteen 1/2"
MACHINE SCREWS (16).
1/2" MACHINE SCREW
(16 used in this step)
16
These holes
must be here.
Surface with
no holes
Surface with
no holes

Step 12
Page 16
å Fasten the LEG ASSEMBLIES (N and O) and
BRACES (P) to the BOTTOM (F). Tighten ten 1-3/8"
MACHINE SCREWS (13).
H
J
I
K
K
F
1-3/8" MACHINE SCREW
(10 used in this step)
13
P
O
N
Surface with
no holes
Surface with
no holes
P

å Carefully turn your unit over onto its front edges.
å Fasten the BACK BRACES (Q) to the LEG ASSEMBLIES (N
and O). Use four 1/2" MACHINE SCREWS (16).
Step 13
Page 17
O
N
Q
Q
1/2" MACHINE SCREW
(4 used in this step)
16

å Fasten the SHELVES (G) to the LEG ASSEMBLIES (N
and O) and SHELF BRACES (R). Use ten 1-1/4" FLAT
HEAD SCREWS (14).
Step 14
Page 18
R
G
G
R
O
N
1-1/4" FLAT HEAD SCREW
(10 used in this step)
14

å Turn four SMALL CAM SCREWS (6) into the exact holes
shown in the DRAWER FRONT (S).
Step 15
Page 19
S
6

Step 16
Page 20
å Insert two SMALL WOOD DOWELS (8) into the DRAWER SIDES (U and V).
å Insert four SMALL HIDDEN CAMS (5) into the DRAWER SIDES (U and V) and DRAWER BRACE (X).
å Fasten the DRAWER SIDES (U and V) and DRAWER BRACE (X) to the DRAWER FRONT (S). Tighten four SMALL
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the DRAWER SIDES insert into the holes in the DRAWER FRONT.
å Push two CAM COVERS (10) onto the SMALL HIDDEN CAMS in the DRAWER SIDES (U and V).
å Then, slide the DRAWER BOTTOM (W) into the grooves in the DRAWER SIDES (U and V) and DRAWER FRONT (S).
5
8
(2 used)
(4 used)
S
X
V
U
Groove
Groove
S
V
U
W
Unfinished surface
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
10
10