Teknion Interpret Operating and maintenance instructions

24" - 48" wide Return Frame for Single Worksurface (WWSRS),
24" - 48" wide Single Return Worksurface (WWWRRS)
Part and Product Identification
For Customer Support please contact
[email protected]
Section:
Description: Page No:
Date:
Rev. No: 02
Jan. 2017 1 of 6
INT_003b
interpret
Curve Leg without infill shown
G- Single Return Worksurface
(WWWRRS) x1
C - 1/4-20x3-12 Flat Head Machine
Screw Quadrex Drive
(E01-0771) x2
B3 - 5/16-18 Hex Nut, 1/2 A/F, .265
(E01-0755) x14
B1 - Reverse Transverse Beam
Assembly
(N02-3696) x2
D - Flush Plate
(A15-6948) x2
E- #10x0.875" LG. Screw, Quad. Pan
Washer
(E07-0077) x8
F - Front Standoff
(B02-0658) x4
B2 - 5/16-18x2.5 Long, Socket Head
Cap Screw
(E01-0756) x14
Pre assembled
A1 - Curve Leg with Wood Infill
(N02-2365) x1
or
Curve Leg with Glass Infill
(N02-2349) x1
or
Curve Leg Open
(N02-2363) x1
A2 -Curve Leg Leveler Add-on
Puck
(A18-0242) x8
Pre assembled
OR
OR
A2
A1
B1
D
F
G

Section:
Description: Page No:
Date:
REMOVE MOUNTING SCREWS CLAMP RELOCATION DETAIL
INT_003b
2 of 6
Jan. 2017
interpret
A1
A2
B2
B3
End Gable Connection (Curve Leg)
Mid Gable Connection
STEP 1: Remove pairs of Screws and Nuts on both ends of Wing Beams Assemblies as shown.
Save for a future installation steps. Determine the type of Connection is on each end. Change
Mid Gable Connection to Beam Connection by removing Clamp Brackets and moving them
one hole forward as shown. Remove Level Pucks from the Curved Leg Assembly.
Beam Connection
Mid Gable Connection
Beam and Screw
position during
future installation
Beam Connection: Partially see through Clamp. After connection is done, you can see
Bolts on the other side of Transverse Beam.
B3
B2

Section:
Description: Page No:
Date:
FASTEN BEAMS TO THE LEG ASSEMBLY ATTACH TO DOUBLE SIDED FRAME
INT_003b
3 of 6
Jan. 2017
interpret
STEP 2: Attach Beam Assembly to Curve Leg. Use holes on the Gable as indicated. Make sure
to use End Gable Connection ends of Beams. Fasten, but do NOT TIGHTEN!
Position End Gable
with holes facing inward.
STEP 3: Bring Single Return Frame assembly to previously assembled Double - Sided Frame at
specified location.
NOTE: Revere Screws and Nuts when
Curve Leg
has a solid or glass infill.
B3
B2
A1
End Gable Connection
Double Sided Frames

Section:
Description: Page No:
Date:
FASTEN TO DOUBLE SIDED FRAME LEVEL, SQUARE, INSERT LEVELER COVERS
INT_003b
4 of 6
Jan. 2017
interpret
STEP 4: Fasten LOOSELY using Socket Cap Screw and Nuts, with Nuts placed on the top and
Screws inserted from the bottom to allow for future adjustment.
STEP 5: Insert Add on pucks, level and square frames. For accuracy Laser Lever is
recommended. Lock levelers in position and slide Leveler Covers inside legs.
Part of
Double Sided
Frame Kit
NOTE:Use as many Pucks as required. They have to
be FULLY ENGAGED and there should be NO
SPACE between Pucks and the bottom of Curve Leg
frame.
B3
B2
B3
B2
A2
A2
bottom of Curve Leg frame

Section:
Description: Page No:
Date:
INSERT FRONT STANDOFFS WORKSURFACE ALIGNMENT
INT_003b
5 of 6
Jan. 2017
interpret
Step 7: Line up inserts under the Worksurface and holes in Clamp Brackets and drop
Worksurface on the Frame. Line up edges as shown. Slide Clamp Brackets on the Beam if
adjustment is necessary.
STEP 6: Insert Front Standoffs, spacing them evenly along both beams. Place and fasten
Worksurfaces to the top of Double Sided Frame/s. Refer to INT_002a,b for instructions.
Double sided Frame
Worksurface.
Wire Gap shown.
G
H
Align
edges

Section:
Description: Page No:
Date:
FASTEN WORKSURFACE DETAILS
INT_003b
6 of 6
Jan. 2017
interpret
STEP 8: Attach Worksurface to the Frame using machine screws. Connect Worksurfaces with
Flush plates. Tighten all screws.
D
H
E
F
E
D