Tektronix RM2000B User manual

RM2000B
TDS1000B, TDS1000C-EDU, TDS2000B, and TDS2000C Series
Rackmount Kit
ZZZ
Instructions
xx
Warning
The servicing instructions are for use by qualified personnel
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do so. Refer to all safety summaries
prior to performing service.
www.tektronix.com
*P071198401*
071-1984-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
DisconnectPower. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
RM2000B Rackmount Kit 1

Service Safety Summary
2RM2000B Rackmount Kit

Kit Description
The RM2000B rackmount is designed for use with TDS1000B, TDS1000C-EDU,
TDS2000B, and TDS2000C series oscilloscopes.
Products
TDS1000B and TDS1000C-EDU Series All serial numbers
TDS2000B and TDS2000C Series All serial numbers
Kit Parts List
NOTE. This kit is suitable only for TDS1000B, TDS1000C-EDU, TDS2000B, and
TDS2000C oscilloscopes. Do NOT use this kit for TDS1000 or TDS2000 models.
Table 1: Kit parts list
Circuit/
figure
Number Quantity Part number Description
1-1 1 each RM2000B RM2000B Rackmount kit, includes a
front and back panel set, 2 handles,
instructions, bag of screws
-2 1 each 071-1984-xx RM2000B Rackmount kit instructions,
English (this document)
-3 1 each 016-1978-xx Standard mounting hardware in plastic
bag includes:
4 each –(for handles) screw 8-32 x 1/2 phil pan
4 each –(for handles) #8 med spit L/W
4 each –screw 10-32 x 3/4 poz
RM2000B Rackmount Kit 3

Kit Description
Table 1: Kit parts list, (cont.)
Circuit/
figure
Number Quantity Part number Description
4each –screw 12-24 x 3/4 poz
4each –screw M5 x 16 oval head phil
4each –screw M6 x 16 oval head phil
4each –flat washer (M5 and #10 screws)
4each –flat washer (M6 and #12 screws)
4each –#10 finish washer
To install a TDS1000B, TDS1000C-EDU, TDS2000B or TDS2000C series
instrument, refer to the following illustration.
Figure 1: RM2000B Rackmount assembly
Figure 2: Dimensions of the RM2000B Rackmount
4RM2000B Rackmount Kit