Tektronix TTR500RACK User manual

TTR500RACK
Rackmount Kit
ZZZ
Installation Instructions
xx
www.tek.com
*P071349201*
071-3492-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 50 0
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.

General safety summary Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To avoid damage to
equipment and personal
injury
Do not exceed rackmount weight ratings. Use this rackmount kit only for TTR500
instruments.
Use proper hardware. Do not interchange hardware. Use only specified mounting
screws.
Use care when installing and removing product from rack. Avoid pinching
fingers and hands when installing and removing. Do not force the product when
installing. Gently pull the product out when removing.
Use only with specified products. Do not use rackmount on products for which
it was not intended. Refer to individual product manuals for details or contact
Tektronix Customer Service when in doubt.
TTR500RACK Rackmount Kit Installation 1

Kit description
Kit description
The rackmount kit is a collection of parts that, once installed, holds one or two
Tektronix TTR500 Vector Network Analyzers, for mounting onto a standard
19-inch equipment rack. To complete the installation, you need
Phillips #2 screwdriver
T10andT20Torxdrivers
3/8 inch nut driver (wrench or socket)
Supported products
TTR503A
TTR506A
Kit parts list
Use the figure to identify the parts contained in this kit and assemble the
rackmount. Some hardware may not be necessary for your configuration.
Item
no. Name and description Qty. Notes
1BRACKET, MAIN 1
2RACK SLIDE 2
3RACK SAFETY STOP LEVER 2
4RACK SAFETY STOP BUSHING 2
5SCREW
#8–32*1/2, FLAT HEAD 100° PHILLIPS
2
6SLIDER SCREW
#8–32*1/4 TORX T20
2
7RACKMOUNT SCREW
#10–32*5/8 PHILLIPS
10
8RACK RAIL, REAR 2
9 NUT
#10–32*3/8 LOCK WASHER
4
10 RACK RAIL, FRONT 2
11 NUT PLATE
#10–32*1/8, 3–POSITION
2OPTIONAL USE
12 INSTRUMENT FEET SCREW
M3–L6, TORX T10
4AVAILABLE ON INSTRUMENT
2 TTR500RACK Rackmount Kit Installation

Kit description
TTR500RACK Rackmount Kit Installation 3

Kit description
Installation
Use this procedure and refer to the illustration to assemble the rackmount
hardware and install the instrument into the rack.
1. Attach the front rack rail (10) to the rear rack rail (8) using the #10–32x5/8
screws (7) and the #10–32x3/8 lock washer nut (9).
2. Attach the pair of rack kit rails to the rack frame using the #10–32x5/8 Phillips
screw (7). Optionally, you can also use the #10–32x1/8 3–position nut plate
(11) if the rack threads are damaged.
3. Attach the rack slide (2) to the main bracket (1) using the #8–32x5/16 Torx
T20 screw (6).
4. Attach the rack safety stop lever (3) to the main bracket (1) using the rack
safety stop bushing (4) and the #8–32x1/2 Phillips flat head 100° screw (5).
5. Slide the main bracket assembly (1) into the rack rail assembly.
6. Remove the four M3 L6 Torx T10 screws (12) that are used to attach the
rubber feet to the bottom of the TTR500 instrument.
7. Use the M3 L6 Torx T10 screws (12) to attach the TTR500 instrument to
the main bracket assembly (1). The rackmount kit can support up to two
TTR500 instruments.
8. Secure the main bracket assembly to the rack frame using #10–32x5/8 Phillips
screws (7).
4 TTR500RACK Rackmount Kit Installation