Telefunken TTV-29N02 Owner's manual

MODEL TTV-29N02
68cm COLOUR TELEVISION
Description:
Job No.
Ref:
REV:2
Engineering Dept:
Artwork By:
Checked By:
Approved By:
Brand Name:
P/No.
Scale:
Date:
Date:
Date:
MANUAL(5P60)
29N03
2004-08-18
48105 TELEFUNKEN

SPECIFICATIONS
Design and specifications are subject to change without prior notice.
Receiving System : B/G
Colour System : PAL / NTSC Playback
Picture Tube : 68cm (29") diagonal
Ext. Antenna : 75 Ohm Coaxial Cable
Ext. In/Out : Side AV-In , S-Video
Speaker : 8
REMOTE CONTROL
Transmitting System : Infrared
Power Supply : DC 3V (1.5 x 2)
Dimension : 28(W) x 155(L) x 45(D)mm
Net Weight : 83 g
Audio/video -in/out ,
Ohm(12W) x2
Audio Output(MAX) : 1KHZ 0.5Vrms, 6Wx2
10% THD Audio Output Power : 1KHZ 0.5Vrms, 6Wx2
Power Consumption : AC 220-240V 50/60Hz, 150W MAX
Standby Power Consumption : AC 220V 50/60Hz, 5W MAX
Dimension : 810(W) x 500(D) x 595(H)mm
Net Weight : 36.5 kg

CONTENTS
INTRODUCTION...............................................................................................................................
WARNINGS and CAUTIONS ............................................................................................................
CONTROL LOCATION .......................................................................................................................
INPUT and OUTPUT .........................................................................................................................
OPERATION INSTRUCTIONS ...........................................................................................................
LOCATION OF CONTROL(REMOTE CONTROL UNIT) ....................................................................
BATTERY INSTALLATION............................................. ....................................................................
SERVICE TIPS ..................................................................................................................................
2
3 - 4
5
6
7-10
11-13
14
15
-1-

INTRODUCTION
INSTALLATION
CAUTION
Locate the receiver in the room where direct light does not strike the screen.
Total darkness or a reflection on the picture screen can cause eyestrain.
Allow enough space between the receiver and the wall to permit ventilation.
Avoid excessively warm locations to prevent possible damage to the cabinet or premature component
failure.
This TV receiver can be connected to AC 220-240 Volts. 50/60 Hz. Never connect to DC supply or any
other power supply.
Do not install the receiver in a location near heat sources such as radiator, air ducts, direct sunlight, or in
a place somewhere like close compartment and close area.
Do not cover the ventilation openings when using the set.
Soft and indirect lighting is
recommended for comfortable viewing.
Never tamper with any components inside your set, or any other adjustment controls not mentioned in
this manual. All television receivers are high voltage instruments. Your PICTURE TUBE is highly evacuated.
Scratching, chipping or undue pressure is dangerous and should be avoided. To clean, the power cord
should be pulled out from the plug receptacle, then wipe the receiver with a dry soft cloth. During thunder
and lightning storms, unplug the power cord and antenna cord to prevent your TV set from damage.
-2-
Thank you for purchasing this television. To get the most out of this unit please carefully read the
instructions and keep them in a safe place for future reference.

WARNINGS and CAUTIONS
Warning
High voltages are used in the operation of this
television receiver. Do not remove the cabinet
back from your set. Refer servicing to
qualified service personnel.
Warning
To prevent fire or electrical shock hazard , do
not expose the television receiver to rain or
moisture.
Warning
Do not drop or push objects into the televi-
sion cabinet slots or openings.
Never spill any kind of liquid on the television
receiver.
Caution
If the television is to be built into a
compartment or similarly enclosed , the
minimum distances must be maintained .
Heat build-up can reduce the service life
of your television , and can also be danger-
ous.
-3-

WARNINGS and CAUTIONS
Caution
Never stand on, lean on or push suddenly the
television or its stand .You should pay special
attention to children. Serious injury may result if it
should fall.
Caution
Do not place your television on an unstable cart ,
stand , shelf or table .Serious injury to an individual ,
and damage to the television, may result if it
should fall.
Caution
When the television receiver is not used for an
extended period of time , it is advisable to
disconnect the AC power cord from the AC outlet .
Caution
Avoid exposing the television receiver to direct
sunlight or other sources of the heat .
Do not stand the television receiver on other
products which give off heat , eg. video cassette
player, audio amplifier.
Caution
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure
of electrical component.
Caution
Do not squash power supply cord under the
television receiver.
-4-

CONTROL LOCATION
-5-
1. Main Switch
2. Remote Sensor
3. Power Indicator
4. Program Down/Up Button
5. Volume Down / Up Button
6. Menu Button
7.
8. Speakers
9. Side AV In
10. YUV(Y, Cb, Cr) In
11. S-Video In
12. AV In1
13. AV Out
14. AC Power Cord
15. Antenna Input Socket (75 Ohm)
AV/TV Button
14
8 2 8 1
3
4
95 6 7
10 15 11 12 13

-6-
INPUT AND OUTPUT TERMINALS
It can be connected to the following appliances: video-tape recorder, video camera, tape recorder and
audio amplifier, etc.....
*Please keep AC cord unplugged when connecting TV system.
*Do not Connect AV IN 1(VIDEO) and S-VIDEO at the same time.
RIGHT
S-VIDEO
75 ANT
RIGHT
LEFT
VIDEO
LEFT
AV OUT
AUDIO
YCb Cr AV IN 1
AUDIO
LEFT RIGHT
YUV IN

OPERATION INSTRUCTIONS
PICTURE SOUND TIME TUNE
MENU BUTTON
1.Press this button to select PICTURE¡¢SOUND¡¢TIME¡¢SETUP¡¢TUNE¡¢EXCHANGE menu cyclically.
2.After enteringinto eachmenu, youcan select submenu whichyou willadjust withPROG.+/- Buttons or
(GREEN) / (BLUE) buttons. Then you can adjust it with VOL.+/- Buttons or the (RED) / (YELLOW).
Picture Button
Sound Button
EXCHANGE
1.You can select the
VOLUME.BASS.TREBLE.BALANCE.TRUBASS.SURROUND item with the
PROG+/- buttons or the (GREEN) / (BLUE) buttons.
2.You can adjust VOLUME.BASS.TREBLE item with VOL+/- buttons or
(RED) / (YELLOW) buttons.
3.You can turn the TRUBASS.SURROUND item ON or OFF with VOL+/-
buttons or (RED) / (YELLOW) buttons.
*TRUBASS item is optional.
*TRUBASS technology is incorporated under license from SRS Labs ,Inc.
*HUE is displayed only for NTSC system.
*TILT and COMB FILTER item is optional.
*TILT is for GEOMAGNETISM ,You can change the TILT to move
picture to a better position.
*When you set comb-filter ON ,the image quality will be improved sharply.
*Comb-filter cannot be set ON when no colour or in S-VIDEO mode.
1.You can select the CONTRAST.
BRIGHTNESS.COLOUR.SHARPNESS.HUE.
BLACK STRETCH. TILT. COMB FILTER item by pressing PROG+/- buttons
or (GREEN) / (BLUE) buttons.
2.You can adjust the
CONTRAST.BRIGHTNESS.COLOUR.SHARPNESS.HUE.
3.TILT item by press VOL+/- buttons or (RED) / (YELLOW) buttons.
CONTRAST
BRIGHTNESS
COLOUR
SHARPNESS
HUE
BLACK STRETCH
TILT
COMB FILTER
PICTURE
75
48
48
75
0
OFF
0
ON
VOLUME
BASS
TREBLE
BALANCE
TRUBASS
SURROUND
SOUND
6
50
50
0
ON
ON
SETUP
WARNING: The main power switch ( of the control location page ) is the manually operated
mechanical switc . The remote control can not cut off power supply to the TV set. For safety purpose,
push main switch to the OFF position and make sure the power indicator goes out when not use for long
time. Push the power "ON/OFF"switch to the ON position, and then power indicator will light up, the
picture (or blue screen) will appear within a few seconds.
No.1
h
-7-

OPERATION INSTRUCTIONS
TIMERS 1.CLOCK
Select hour or minute with
Adjust CLOCK time with
You can press CLOCK buttons to display currently clock time.
2.ON TIME
Select hour or minute with
Adjust ON TIME with
3.ON PROG.
Select ON PROGRAM with
4.OFF TIMER
Select hour or minute with
Adjust REMIND time with .
5.SLEEP TIMER
Set SLEEP TIME with
6.REMINDER TIMER
Select hour or minute with
Adjust REMIND TIME with
7.REMIND PROG
Select REMIND PROGRAM with
PROG+/- buttons or (GREEN) / (BLUE)
buttons
VOL+/- buttons or (RED) / (YELLOW) buttons
PROG +/- buttons or (GREEN) / (BLUE)
buttons.
Vol+/- buttons (RED) / (YELLOW) buttons.
VOL+or (RED) buttons.
PROG+/- buttons or (GREEN) / (BLUE)
buttons.
VOL+/- buttons or (RED) /(YELLOW) buttons
VOL+/- buttons or (RED)/(YELLOW) buttons.
PROG+/- buttons or (GREEN)/(BLUE)
buttons.
VOL+/- buttons or (RED)/ (YELLOW) buttons.
VOL+/- buttons or (RED)/(YELLOW)
buttons.
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
TIME
--:--
--:--
1
--:--
20
--:--
1
-8-
* Timer function will need resetting when you switch off the TV set by
the main power switch or unplug the power cord.

OPERATION INSTRUCTIONS
SETUP Button You can select the item by pressing PROG+/- buttons or (GREEN)/ (BLUE)
Buttons.
then you can adjust it by Vol+/- buttons or (RED)/(YELLOW) buttons.
1.LANGUAGE
You can select the on-screen display language.
2.BACK GROUND
Press VOL+/- buttons or (RED) /(YELLOW) buttons to set it ON or OFF.
For BACKGROUND, only when no signal is input in TV mode.
3.NOISE REDUCE
Press VOL+/- buttons or (RED) / (YELLOW) buttons to set it ON or
OFF. For Noise REDUCE, only in TV mode.
4.CHILD LOCK
Press VOL+/- buttons or (RED) / (YELLOW) buttons to set it ON or OFF.
If you set it ON, the key on the TV set is disable and only the remote
control functions.
5.CALENDAR
Press VOL+/- buttons or (RED) / (YELLOW) buttons to enter into
CALENDAR menu.
CALENDAR
1.Press VOL+/- buttons or (RED) / (YELLOW) buttons to select
YEAR, MONTH or DATE.
2.Press PROG+/- buttons or (GREEN) / (BLUE) buttons to adjust
YEAR, MONTH or DATE.
3.Press MENU Button to return.
S M T W T F S
1
8
15
22
2 3 4 5 6 7
910 11 12 13 14
16 17 18 19 20 21
23 24 25 26 27 28
29 30 31
Y:2002 M:12 D:12
LANG.
BACK GROUND
NOISE REDUCE
CHILD LOCK
CALENDAR
SETUP
ENGLISH
ON
OFF
OFF
* CALENDAR item is optional . Please see actual TV set.
-9-

OPERATION INSTRUCTIONS
TUNE MENU
You can select the item by press the PROG+/- buttons or the (GREEN) /
(BLUE) buttons, move to the menu you select and then do as follows.
1.COLOUR SYS
Press VOL+/- buttons or (RED) / (YELLOW) buttons to set the colour
System. Australia is PAL B/G.
2.SOUND SYS
Press VOL+/- buttons or (RED) / (YELLOW) buttons to set the sound
system. Australia is 5.5M.
3.BAND
Press VOL+/- buttons or (RED) / (YELLOW) buttons. You can select the
Band VHF-L.VHF-H or UHF.
VHF-L-----VHF-H-----UHF
4.SKIP
Press VOL+/- buttons or (RED) / (YELLOW) buttons to set skip on or off,
when you set skip on. This program will be hidden.
5.PROGRAM
Press VOL+/- buttons or (RED)/(YELLOW) buttons to set the PROGRAM
number.
6.FINE TUNE
For better quality with VOL+/- buttons or (RED) / (YELLOW) buttons.
7.SEARCH
Press VOL+/- buttons or (RED) / (YELLOW) buttons to search for next or
previous available program, the set will automatically stop while the signal
is received.
8.AUTO SEARCH
Press VOL+/- buttons or (RED) / (YELLOW) buttons, the TV set will
automatically search in 3 bands and store every program.
CONLOUR SYS
SOUND SYS
BAND
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH
TUNE
AUTO
M
VHF-L
OFF
2
EXCHANGE MENU In AV mode ,this item will not be displayed.
Select the item by pressing the PROG+/- buttons or the (GREEN)/(BLUE)
buttons.
1.
Press VOL+/- buttons or (RED) / (YELLOW) buttons to adjust
2.PROGRAM 2
Press VOL+/- buttons or (RED) / (YELLOW) buttons to adjust PROGRAM 2.
PROGRAM 1
PROGRAM 1.
3.Press VOL+/- buttons or (RED) / (YELLOW) buttons to exchange
PROGRAM 1 and PROGRAM 2.
PROGRAM
PROGRAM
EXCHANGE
EXCHANGE
1
1
-10-
*In AV mode, only COLOUR SYS displayed under this menu.
*After fine tune. The colour of program number will change from GREEN
to YELLOW.

LOCATION OF CONTROL (REMOTE HANDSET UNIT)
-11-
STANDBY BUTTON( )
Press this button to turn the TV on/off. Press any
Number Button or Program Up/Down Button, picture
and sound will appear on within a few seconds.
STEREO/MONO DUAL CH I/II
BUTTON(I/II)(OPTION)
The third line on the top right corner of the screen
automatically changes to green when a NICAM
broadcast is received.
As stereo program is received. You can select STEREO.
MONO. or FM by pressing the ST/MO/I/II button.
As bilingual program is received. You can select DUAL-
1,DUAL-2 or FM by pressing the ST/MO/I/II button.
Remark: FM: Standard mode STEREO: Stereo
mode MONO:Mono mode
DUAL-1: multi sound channel for language 1
DUAL-2: multi sound channel for language 2
SLEEP BUTTON( )
This key is used to set the sleep timer from in 10
minutes step up to three hours. When the preset time
runs to 0, the TV set will go into standby mode.
*If no program received, the TV set will switch to
standby automatically in 5 minutes.
SOUND SYSTEM BUTTON (SYS.)
When the sound system is incorrect, press this button
to select the correct sound system.
PROGRAM UP/DOWN BUTTON (PROG. +/-)
Press the Program Up Button to select the program
forwards.
Press the Program Down Button to select the program
backwards.
2
456
8
79
AV/TV
MENU
PROG.-
VOL.+VOL.-
0
3
PROG.+
--/---
1

LOCATION OF CONTROL (REMOTE HANDSET UNIT)
SOUND MODE BUTTON(S.M.)
Press this button to select the desired sound mode, USER. SPEECH. and can be
selected cyclically.
THEATER MUSIC
PICTURE MODE BUTTON(P.M.)
Press this button to select the desired picture mode, RICH. USER. SOFT and STANDARD can be selected
cyclically.
MUTE BUTTON( )
Press once to mute the sound, press again to return to previously set sound level. MENU RECALL
BUTTON.
VOLUME UP/DOWN BUTTONS (VOL.+/-)
Press Volume Up/Down Buttons to adjust sound level.
PROGRAM SELECTION BUTTONS(0-9)
Push the number for your desired program and the program indicator will be displayed on the screen.
Press number key 0-199 for program selection.
DIGIT BUTTON(--/---)
Press this button to select program between 0-199 program.
To select a one-digit number: press "--/---" button to display "-",then press 0-9 to select a number 0-9,or
press the number 0-9 direvtly.
To select a two-digit number: press "--/---" button to display "--".then press 0-9 to select a number 10-99.
To select a three-digit number: press "--/---" button to display "1--".then press 0-9 to select a number 100-
199.
MENU RECALLBUTTON( )
Press this button sequential to recall for the program number, system, logo etc on the screen..
*Both of the sound mode"SPEECH,MUSIC, THEATER" or picture mode "RICH, SOFT , STANDARD" are
fixed by factory, all the change of these settings will be saved into the" USER"mode automatically.
-12-
MENU BUTTON(MENU/INDEX)
In TV mode, this button is used as MENU command.
MENU: To use MENU button for the turning procedure, please refer to page 7-10 for the details.
INDEX: Press INDEX button to obtain the index page.
AV MODE BUTTON (AV/TV)
In TV mode, used as AV command.
AV: Press this button to display external video signal such as VCR or CD video player.

PICTURE MENU BUTTON(PICTURE/SIZE)
In TV mode, used as PICTURE menu command.
PICTURE: Press this button to enter into the PICTURE menu directly.
SIZE: The top or botton half of any page can be enlarged by pressing this button.
SETUP MENU BUTTON(SETUP/HOLD)
In TV mode, used as SETUP menu command.
SETUP: Press SETUP button to enter into the setup menu directly.
HOLD: Sub-pages will scroll automatically. Press HOLD button a hold a sub-page. To release the page.
Press HOLD again.
TUNE MENU BUTTON(TUNE)
In TV mode, used as TUNE menu command.
TUNE: Press this button to enter into the TUNE menu directly.
SOUND MENU BUTTON(SOUND/ RECALL)
In TV mode, used as SOUND menu command.
SOUND: Press this button to enter into the SOUND menu directly.
RECALL :Sometimes the answers of quizes, jokes etc are hidden. Press REVEAL button to reveal the
hidden information.
-13-
Q.VIEW BUTTON(Q.VIEW)
In TV mode, used as Q.VIEW command.
Q.VIEW: Press this button to return to the previously viewed program.
GAME BUTTON(GAME)
In TV mode, used as GAME command.
GAME: You can play the game on TV. To speed up with PROG - , transform with PROG + .Shift left with
VOL-, shift right with VOL+.
CLOCK BUTTON(CLOCK)
In TV mode, used as CLOCK command.
CLOCK: Display the time on the top right corner of the screen.
LOCATION OF CONTROL (REMOTE HANDSET UNIT)

BATTERY INSTALLATION (REMOTE CONTROL UNIT)
THE CAUSES OF INTERFERENCE
1. Remove the battery cover.
2. Insert the 2 UM4-AAA 1.5V batteries making sure the polarity (+ or -) of the batteries matches the
polarity marks inside the unit.
3. Replace the battery cover.
Replace with new batteries when the TV set begins to show the following symptoms:
Operation is unsteady or erratic. Sometimes the TV set does not function with Remote Control
Unit.
Remark:
1) Alkaline Batterie Recommended
2) Remove batteries when they are exhausted or if the remote control is not to be used for a long time.
-14-
Incorporated in your TV receiver are the most up-
to-date devices to eliminate interference. Local
radiation however, can create disturbances which
visibly affect your picture. Proper installation, a
good aerial are your best safe-guards against
these disturbances.
RF INTERFERENCE
Moving ripples across the screen are caused by
nearby transmitting or receiving-short-wave radio
equipment.
DIATHERMY
Herringbone pattern and partial picture loss can
result from the operation of diathermy equipment
from a nearby doctor's surgery or hospital.
SNOW
Weak TV signals from long distant stations result
in an unsteady picture and give the effect of falling
snow. An antenna adjustment or antenna
amplifier may be needed.
GHOST
Multiple image caused by TV signals reflected
back from surrounding buildings, hills, aircraft, etc.
is minimized by correct aerial positioning.
CAR IGNITION
Nearby cars and electrical motors can cause small
streaks across the picture or make the picture roll.

SERVICE TIPS
BEFORE CALLING FOR SERVICE, HAVE YOU
CHECKED ( ) THE FOLLOWING CHART
ON SYMPTOMS AND SOLUTIONS?
No picture, no sound
Poor sound, picture OK
Poor picture, sound OK
Weak picture
Blurred picture
Double image
Lines in picture
Distorted picture
Weak reception on some channels
Horizontal bars
Picture rolls vertically
Poor colour
No colour
Misoperation of Remote control
No Remote control
On Screen Display Control outside the screen
Try differentchannel, ifOK, probably station trouble
Checkaerial connectionson back ofset
Check aerialfor broken wires
Re-orient aerial (if indoortype)
Probably local interference, such as an appliance
Adjustfinetuning control
Adjust brightnesscontrol
Adjustcontrastcontrol
Check if station isbroadcasting colour
Adjust colourcontrol
Checkif systemswitch iscorrect
Checkifon/off switchis"on"
CheckBatteries in Remote control
Solution
Symptoms
-15-