Tentandtable.com GA Bounce Kaleidoscope Castle 7013 User manual

888 322-5606 (toll free)
Instruction
Manual
INFLATABLE AMUSEMENT DEVICE:
BOUNCE HOUSES
(GENERAL INSTRUCTIONS)
RC # 7013 GA Bounce Kaleidoscope Castle
1612 N Broad Street 44 W Ridge Pike
Lansdale, Pa 19446 Limerick, Pa 19468
(215) 362 - 7368 (610) 489 - 2334

888 322-5606 (toll free)
WARNING: Inflatables are very heavy
—do not attempt to roll or move these
games by yourself
•Do not inflate in high winds or rain—
High winds are considered to be
15 mph or higher
• Inspect the site, look for overhead and
underground obstructions— such as
utilities
• Call your local utility to have utility
lines marked (call 3–5 days ahead)—
call811.com is a good resource—
‘click’ 811 in Your State
•Use an adequate three wire extension
cord, min. 12 gauge for 50ft. maximum
length—never cut or remove the round
grounding pin from the cord
SET-UP STEP 1. (SAFETY CHECK LIST)
1
Use Ground Cover Tarps
(to protect inflatable)
Secondary escape
opening in roof
Must be positioned on
a FLAT, LEVEL SURFACE
Anchor Straps at base—secure
with recommended stakes
(refer to your state inspection requirements)
2 trained operator/
attendants are required
to supervise this device,
at all times
GFCI extension required
(reduces possibility
of shock)
Commercial Inflatable Blowers needed
1.0 HP / producing minimum 700 cfm @ 4.5˝
(consult manufacture´s safety label for requirements)
Keep individuals
OUT of blower
areas, at all times
Modular Panel Area
(optional)
BOUNCE HOUSES – OVERVIEW
CHECK ALL SPECIFICATIONS
LOCATED ON SAFETY LABEL–
ATTACHED TO YOUR UNIT
OPERATOR/ATTENDANTS ARE RESPONSIBLE FOR THE PATRONS SAFETY, AT ALL TIMES!

• Always connect a GFCI extension cord
adapter to any extension cord before
plugging into a power source—
this reduces the possibility of shock
in wet environments
• Check the GFCI operation at least once
per event
• Before staking unit into the ground,
obtain marking and location information
from the utility companies if there is
a possibility of striking underground
utilities
• Remove all occupants if wind becomes
excessive—deflate unit, if wind continues
• Important, the operator/attendant is
responsible for the safety of those using
the inflatable amusement device
• Pick a location free from overhead
utility lines, trees, roads, sidewalks,
bodies of water and cliffs—or any hazard
• Any nearby obstruction should be at
least 20 feet away from inflatable
• Spread tarps (sold separately) on
the slide/bounce house location, to
protect unit
• Locate the blower and power cord in an
area that is not in a direct walkway—be
sure the blower is on a flat and dry surface
• A minimum of 2 installers recommended
Recommended Tools and Equipment:
sledge hammer, ground tarp, hand truck
or 4 wheel dolly, crowbar/stake remover
safety goggles, GFCI extension adapter,
50´ 12AWG extension cord
• Carefully place unit, using dolly, at one
end of tarp—it’s easier to move at this
stage!
• See (drawing), find back end of inflatable
device and roll onto tarp
• (Make a mental note or snap a picture of
how the inflatable is folded and positioned
as you unroll the game. This will be
beneficial when you re-roll the device later)
• Check location, make any adjustments
before inflation—unfold device completely
• Start the staking process— place stakes
through the inflatable anchor straps,
all around the inflatable amusement
device—see (pg. 3) for proper staking
SET-UP STEP 2. (SITE ASSESSMENT)
SET-UP STEP 3. (UNROLL AND POSITIONING)
Roll onto tarp
Ground cover tarp Set-up on a flat surface
SET-UP (SAFETY CHECK LIST - cont.)
888 322-5606 (toll free)
2
If previously packed
correctly, this end
(with inflation tubes)
should be the back
of inflatable
GFCI extension required
(reduces possibility of shock)
GFCI= Ground Fault Circuit Interrupter
A GFCI extension cord adapter can be
purchased at most Do-It-Yourself type stores
• Use an adequate three wire extension cord,
min. 12 gauge for 50ft. maximum length
• Check GFI at least once per event

3
888 322-5606 (toll free)
• Plug the blower power cord into the GFCI
extension, then plug the GFCI extension
into the extension cord—connect the
fan cone to the inflation tube
• Two inflation tubes used for this game
• Close off the unused inflation tubes
• Plug the extension cord into the power
source
• Check the inflation tube to make sure it
is properly attached to the blower fan
—the inflation tube must be properly
closed around the blower outlet cone
to prevent large air leakage
• Close all zipper vents (if applicable)
• Locate the on/off switch (if applicable)
on the blower and turn it on—observe
the inflation of the inflatable as it rises
• When inflation is almost finished, check
the positioning of the stakes—hammer
them all the way in— see (step 5)
• Note: For medium soil conditions, larger
stakes will increase pullout capacity*
• Once inflated, check for any rips, holes,
or damage
• When properly inflated, all inflated
areas of the game will become
pressurized and firm
Important: Keep blower on,
continuously, for the duration of your
event— to maintain proper inflation
SET-UP STEP 5. (PROPER STAKING)
Hammer all the
way in— hook
end should be
touching the
ground
Slide stake through
D-ring and position
hook away from
inflatable
SOIL CONSISTENCY:
Stake in Hard, Stiff or Medium soil
DO NOT Stake in Soft soil
(check ASTM f2374-17 standards)
Slide feet first only! Do not slide head first!
CORRECT!
One at a time! No double sliding!
ARMS CROSSED,
FEET TOGETHER
Do not touch sides
with hands or feet,
all the way down
SET-UP STEP 4. (INFLATION TUBES)
The following instructions must be read
and adhered to by all operator/attendants
regarding this inflatable device:
• Trained attendants should be positioned
at the entrance and exit of device
• Attendants must be at least 18 years old
•
Trained operator/attendants should assist
the movement of all child patrons as they
enter and exit the amusement device
• Attendants should remove all debris from
the inflatable prior to allowing persons
to enter or climb on inflatable
• Trained attendants should only allow
persons of the same size and age on the
inflatable device at the same time—
(check capacity on device warning label)
OPERATING INSTRUCTIONS
Twist tube
twice
Fold
Wrap both
sides and
secure tightly,
around tube
Wrap one
side and secure
tightly
1. 2.
3.
Unused Inflation Tube Inflation Tube
Anchor straps should be
fully extended, away
from unit
(FOR INFLATABLES WITH A SLIDE)

No Sharp Objects No Running–to Enter No Food or Drink
No Chewing Gum No Cell Phones No Loose Objects
in Pockets
888 322-5606 (toll free)
• People with medical conditions or severe
disabilities should not use this Inflatable
amusement device
• Attendants should make sure that no one
enters the inflatable device with shoes
on, eyeglasses or sharp objects in their
hair or on clothing
• Attendants should observe patrons at all
times while they are in the inflatable
• Attendants should be close enough to
be able to warn against flips, piling on,
wrestling, bouncing against side,
grabbing net or bouncing too close to
each other—attendant should ask anyone
doing these things, after being warned,
to leave the inflatable device immediately
• Whistle use required for attendants
• No running to enter the inflatable device
• The attendant should point out and make
customers aware of the posted warning
sign on the front or side of the inflatable
• Attendants should watch for any signs of
deflation such as sagging, wrinkling or
distortion—if observed, the attendant
should ask the people in the inflatable
to evacuate, calmly and safely
• Attendants should keep all spectators
outside the inflatable amusement device
and at least 5 feet away from the sides
• Starting line is 48 inches from the entry
of the inflatable amusement device
• Prohibit excessive rough play by
occupants—blow whistle
• In times of excessive heat monitor
the
heat inside play area and slide surface
• Do not allow any individual in the rear
of the game or near the electric blower
at any time
• Deny entry if any patron poses a risk to
others— or, if they consumed alcohol or
illicit drugs
• 15mph wind equals; dust and loose paper
rising and movement of small branches
—Hazardous winds; small trees sway and
large branches are in motion
• Check the blower/inflation tube regularly
to ensure there isn't any excessive
leakage
• Check stakes regularly
• Keep airborne trash/leaves clear of
blower intake
OPERATING INSTRUCTIONS - cont.
Monitor the weather throughout
the day, check for high wind
(15mph or higher), rain, snow
and lightning—do not use device
in these conditions
If lightning occurs,
evacuate the unit
immediately—
unplug power
OPERATING INSTRUCTIONS - cont.
Keep clear a 5 foot
safety area around
inflatable device
No hanging or
climbing on
outside walls
ASTM Int’l guideline calls for a 4 ft. Impact Mat at entry and
exit points—center either a 4x4, 4x6 or 4x8 mat at each opening
OPERATING INSTRUCTIONS - cont.
15 mph!
4
The inflatable should not be
operated if the wind exceeds 15 mph,
or at temperatures of less than 40º F

BLEACH
• Do not use M.E.K.(methyl ethyl ketone)
to try and clean your inflatable, as this
will damage the vinyl
• Do not use a chlorine based cleaner or
bleach, as this may damage the threads
• Do not use any cleaning products
containing alcohol to try and clean your
inflatable device, as this will damage any
printing that may be on your inflatable
• Use water and/or mild cleaner sparingly
by sponging
• Excessive water or cleaner may penetrate
the seams and collect inside of the tubes
—also, bubbling from the seams during
operation may occur
CLEANING THE INFLATABLE
Next, align unit
into a rectangle
shape—pancake
top and bottom
Front
Deflation Tubes
—Back of unit,
keep extended
888 322-5606 (toll free)
• Before deflating; Inspect for any damage
and repair as necessary
• Clean inflatable amusement device(s) and
dry, after use—by running air through it
• Unplug blower at the power source
• Loosen first inflation/deflation tube
strap and remove tube from blower cone
—make sure tube is pulled away from
the inflatable and is straight
• Loosen second inflation/deflation tube
strap and pull tube away from inflatable
• Open all deflation flaps
• While the inflatable amusement device
is deflating, remove stakes, put blower
fan away, and store extension cord(s)
• Two people, minimum, needed to fold
• Guide inflatable inward and to the front
—while the air is being released
• Begin folding inflatable amusement
device—pull vertical peaks/shapes toward
the front, to flatten and release more air
• Next, situate top of unit over the bottom,
pancake style—and fold peaks into the
middle, see (drawing)
• Once you make the folds, you will notice
that air is still inside the game—start at
the front and walk, in stocking feet, to
the back—removing most of the air
• Work the air out towards the back of
the unit through the inflation tube(s)
• Commercial inflatables take 5–15
minutes to completely deflate
DEFLATION AND FOLDING- cont.
DEFLATION AND FOLDING
5
Before deflation, remove all accessories that may be
applicable to your unit—also be sure to use a quality
broom and sweep the surface of the game free of
any debris
Check to make sure that no sharp
objects have fallen into the seams
of the game, Eg. pens, pencils, etc.
—items such as these can cause
damage to the inflatable during
the rolling up process

6
888 322-5606 (toll free)
• Fold both sides into the center of the
inflatable—each person should place one
foot on the inflatable at the fold line
• Fold at the same time—walk down the
game and straighten out the seam
• Repeat this procedure for the other half
of the game
• The roll; make sure that at least one of
the inflation tubes is extending—as you
roll the unit up, air will escape and the
inflatable device will roll much better
Important: Twist the beginning of the
‘roll’ very tight
• Start your roll from the FRONT (opposite
the inflation tube)
• As you progress, be sure that the roll is
straight and tight
• Near the end, allow time for the last bit
of air to escape
• Locate tie strap—pull to top of roll
• We recommend you tie a tight slip knot
around the roll
• Stand the inflatable amusement device
on end—place the transport/storage
bag over one end of the game and work
it down as far as you can
• It is important that you work the bag
down to the top of the roll—flip the unit
and pull the bag up over the top of the
inflatable amusement device
• Tie the bag closed
• Lay the game onto a dolly and roll it
to your designated storage area
WARNING: Inflatables are very heavy.
Do not attempt to roll or move these
games by yourself. When lifting any type
of heavy weight, be sure to lift with your
legs and not your back.
If in doubt about your ability to move
something, get help.
STORAGE BAG - (you’re done)
FINAL FOLD AND ROLL
SLIP KNOT (for rolled inflatable)
Fold sides to center
Take through
existing loop,
attached to
bottom of unit,
before knotting
Next, fold one side
on top of other
Roll towards
back, tightly
Rear of Inflatable Inflatable/Deflation
Tube
1. 2. 3. 4.

7
888 322-5606 (toll free)
DIRECTIONS FOR USE:
(operator/attendants should be assisting patrons as they enter and exit the
inflatable amusement device)
• Communicate to all patrons– safety, using the inflatable amusement device,
usage and dress code rules
• Carefully enter inflatable amusement device at the entrance and climb the
incline slowly
• Careful not to collide into other patrons, be respectful of others safety at all times
• When patrons are ready to slide, do so in a seated position, one at a time, with proper
form (patrons may exit carefully out the entrance tunnel, if they do not wish to slide)
• Exit the device, after sliding, as careful as possible—no jumping off the edge of
the device
• As one patron exits, allow another to enter— remember to maintain the correct
device capacity (total number of patrons allowed, at one time)
EVACUATION PLAN:
In the case of rapid deflation or poor weather during operation, attendants should
follow these steps–
• Operator/attendants should blow whistles to evacuate patrons immediately and safely—
aid child patrons as they exit, then tell them to step away from inflatable device
• Any patrons on elevated platforms should climb down the stairs, backwards—if a
patron is sitting ready to slide, let that one
slide down, only (for units with slides)
• Deflate inflatable amusement device if necessary
(high wind)—re-inflate when safe
• Call medical responders if anyone is injured
DAILY CHECK LIST:
• Check wind conditions at beginning of day
and throughout the day.
• Ensure temperatures are greater than 40ºF.
• Recheck the minimum 12 gauge- 3 wire extension
cord and the CFCI (ground fault circuit interrupter).
• Ensure there are no obstructions in the blower.
• Ensure unit is properly inflated.
• Ensure all tether points are secure.
• Ensure all deflation zippers and flaps
are closed.
• Walk around the unit and inspect seams
and search for wear damage.

Staking for this Device: (4) total — 4 anchor straps / 0 tie downs
888 322-5606 (toll free)
DEVICE NAME:
Bounce House (SAMPLE SPECIFICATION PAGE)
DIMENSIONS:
14´x12.5´ x15.5´
INFLATION/DEFLATION TUBES:
(2)
DEFLATION FLAPS:
(1)
DEVICE CAPACITY:
(6) Patrons
BLOWER:
(1) - 1.0 HP
MINIMUM NUMBER OF TRAINED ATTENDANTS:
(2)
MINIMUM HEIGHT / MAXIMUM HEIGHT:
36 in. / 60 in.
ANCHORS / TIE DOWNS:
(4) / (0)
MAXIMUM WEIGHT:
250 lbs. per patron (600 lbs. total limit)
SKU:
XBH-RNBWMOD-14A
4 anchor straps
(1 on each corner)
(entrance/exit)
15´
12.5´
14´
8

9
888 322-5606 (toll free)
MAINTENANCE and INSPECTION
• Determine a cleaning and preventative maintenance schedule to keep this device function properly
• The device can be easily cleaned with a cloth or light brush. Use a vinyl cleaner and rinse lightly,
to remove detergent before storing.
• DO NOT PACK THE INFLATABLE DEVICE WHEN WET. If it wasn’t dried properly, lay the unit out to
dry at the earliest opportunity.
• The unit should be inspected regularly for damage. If there is evidence of tearing at the anchor
points or vinyl panels, the inflatable amusement device should not be used until the repair has been
completed.
REPAIRS
• Repairs made by anyone other than the original manufacturer, shall be made using the same
construction method—with comparable materials—unless manufacturer agrees otherwise.
• To repair small tears up to 12" use "Single Patch Method" as follows.
• Cut an oval or round vinyl patch approximately 4" larger than the cut.
• Clean the area around the tear.
• Apply SX-69 vinyl glue on the patch and on the surface of the inflatable device.
• Allow the manufacture´s recommended drying time before applying the patch to the inflatable device
as indicated on the label on the container.
• Place the patch covering the cut area and apply pressure for 1 minute. Refer to the glue manufac-
turer´s label for the recommended time for glue to dry once the patch is applied.
• If the "Single Patch Method" is not a viable option use PatchALL* for a non-glue repair until you can
apply the "Single Patch Method" or send the unit to a repair facility.
DAILY CHECKLIST
• Ensure maximum winds are less than the manufacturer´s recommended wind
speed requirement for unit.
• Ensure temperatures are greater than 40° F.
• Ensure that a minimum 12 gauge 3 wire extension cord is used with the blower
and is connected to a CFCI (Ground Fault Circuit Interrupter).
• Ensure there are no obstructions in the blower(s), blower intake and the unit´s inflation tubes.
• Inspect the blower inflation tubes, they should be in good condition and firmly fixed to blower.
• Ensure unit is properly inflated—with the blower pointing straight at device.
• Visually inspect device for any holes or rips in the fabric or seams.
• For inflatable amusement devices with multiple units, check all connection points.
• Ensure all tether and anchor points are secure. Check stakes.
• Ensure all deflation zippers and flaps are closed.
• Walk around the unit and inspect seams and search for wear damage.
*PatchALL are clear polyurethane patches or tape. They are quick, flexible, long lasting, airtight and waterproof—with no gluing.
Visit TentAndTable.com for all your Inflatable Accessories including; blowers, impact mats, dollies, heavy-duty hand trucks
and repair kits.
MODIFICATIONS: This inflatable amusement device shall not be altered in any way
that constitutes a major modification without written from the device manufacturer.
*ASTM Int’l recommends 1˝x 26˝ stakes for all commercial inflatable amusement devices, as a guideline. ASTM Int’l supports that this would
be greater pullout capacity in windy condition (still below 15 mph) or, in the case of medium consistency soil conditions.

1-888-322-5606
YES NO
WARNING:
As with any Amusement Device,
there is an inherent risk
of personal injury.
As such, ALL PERSONS play at
their OWN RISK and peril!
If unit begins to deate EXIT immediately!
DO NOT ENTER RIDE – UNLESS ATTENDANTS ARE PRESENT!
DO NOT Operate this unit if WINDS
exceed 15 M.P.H.
DO NOT Inate or use this inatable
without rst SECURING to ground. Use
stakes at all tethering and anchor points.
DO NOT Pound stakes into ground without
rst VERIFYING gas, water & electrical
locations with local UTILITY COMPANIES!
DO NOT Use silly string on unit.
SHOCK HAZARD!
DO NOT Use this equipment on DAMP
surfaces or during inclement weather.
THIS UNIT REQUIRES A CONSTANT SOURCE OF
110V-20amp POWER PER BLOWER SYSTEM.
SAFETY RULES
A MINIMUM OF TRAINED OPERATOR(S)
MUST BE ON DUTY AT ALL TIMES!
ADULT SUPERVISION REQUIRED AT ALL TIMES!
Compliance Statement:
The vinyl and netting material used in the construction of this
product is of the highest quality, 100% lead-free, adheres to
MFR methods and was built to ASTM F2374 standards.
NO
SHOES
NO
UNEVENLY
MATCHED PLAYERS
MAXIMUM
NUMBER
OF PLAYERS
NO
SHARP OBJECTS
NO
ROUGH
PL AY
MINIMUM
HEIGHT
NO
GLASSES
NO
TUMBLING
OR FLIPPING
MAXIMUM
HEIGHT
NO
JEWELRY
NO PERSONS
W/ MEDICAL
CONDITIONS
MAXIMUM
WEIGHT
PER PLAYER
NO
FOOD OR DRINKS
NO
PREGNANT
INDIVIDUALS
HEADGEAR
REQUIRED
Name:
Serial Number:
Stakes Required:
Blower Required:
Made in China
Inated
L W H
Dimensions
H
WL
888 322-5606 (toll free)
CHECK ALL SPECIFICATIONS LOCATED ON
SAFETY LABEL– ATTACHED TO YOUR UNIT