Terra Bound Solutions 02-07-0057 User manual

MODEL # 02-07-0057
ASSEMBLY INSTRUCTIONS
04-11-11
20020 Hickory Twig Way, Spring, TX 77388 | Toll Free: 1-877-857-2915 | www.terraboundsolutions.com

2
MOUNTING OPTION 1
IMPORTANT: Never install play equipment over hard, unresilient
surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.
GROUND
Support
Post
(3) Ground
Spikes
Support Post
4lb
Hammer
Footer
Footer
SURFACING
Footing Detail for Installations
Placed on Ground Level
Instructions:
1. With Footers in position, secure
each footer to the ground using
(3) ground spikes.
NOTE: A 4 lb. hammer may be
required to drive spikes into
the ground.
Install ground spikes angled
inward as shown in illustration.
Clear area of any debris and grade
to level surface to +/- 2°
SITE PREPARATION

3
MOUNTING OPTION 2
Footer
In-ground
Footer
Place brick or
equivalent in the
bottom of all footings
to prevent post from
sinking into the ground
Footing Detail for Installations
Requiring Concrete Footers
Instructions:
1. Bolt Footer and Inground Footer
together using (3)M10 x 20mm(3/4”)
BHCS Bolts, and M10 Lock Nuts.
(3) M10 x20mm
( 3/4”) BHCS
Bolts
(3) M10
Lock Nuts
IMPORTANT: Never install play equipment over hard, unresilient
surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.
GROUND
Support
Post
Footer
SURFACING
Support Post
Footer

5
ATTACH FOOTER POSTS TO CRAWL TUNNEL AND FOOTERS
Parts List
Letter Description Quantity Part Number
A Crawl Tunnel 1 02-07-0057
02-07-0087
02-07-0043
33-12-0058
33-11-0103
33-11-0501
33-11-0005
33-11-0400
B
C
Support Post
Footer
2
4
Hardware Complete 1
D10
E10
F
M8 x 25 BHCS Bolt
M10 x 35 BHCS Bolt
M8 Barrel Nut
G
4
M10 Lock Nut 4
B
C
D
E
A
FG
Figure 1
1. Lower U-shaped Support Post(B) behind
flange of Crawl Tunnel(A).
2. Insert Bolt(D) through center hole in
Crawl Tunnel(A), into Support Post(B) and
secure with Barrel Nut(E).
NOTE: Lightly tighten Bolts(D) until all
Bolts(D) have been inserted.
3. Repeat Step 2 for remaining Bolts(D).
4. Align hole in Support Post(B)
with hole in Footer(C).
NOTE: Use UPPER hole if
using EWF
(Engineered Wood Fiber)
Use LOWER hole if using
2” rubber tiles or poured-
in-place surfacing.
5. Insert Bolt(F) through larger
hole in Support Post(B), into
Footer(C) and through the
other side of Support Post(B)
and secure with Lock Nut(G).
See Figure 1.
6. Repeat steps 4-5 for Remaining
Footers(C).
Use this hole for
EWF
Use this hole for
Rubber Tiles or
Poured-in-place
surfacing

6
SECURE CRAWL TUNNEL TO GROUND
Parts List
Letter Description Quantity Part Number
A Ground Spikes
In-Ground Footer
12 02-07-0048
02-07-0049
33-12-0058
33-11-0002
33-11-0400
B
C
4
Hardware Complete 1
D
M10 x 20 BHCS Bolt 12
12
M10 Lock Nut
ABOVE GROUND INSTALLATION
For Above Ground installation using
Ground Spikes(A), refer to Mounting
Option 1 on page 2.
IN-GROUND INSTALLATION
For In-Ground installation using the
In-ground Footer(B), refer to Mounting
Option 2 on pages 3 and 4.
B
C
A
D
or