The Garden Gym Monkey bar User manual

General guidance
These instructions are provided as a guide to help you
install your equipment. Depending on the type of ground
conditions it may be necessary to modify the installation. If
you are unsure, please consult a qualified professional or
contact the Garden Gym Team. The installation must be
carried out by 2 people. Before digging you must ensure
that there is no risk of encountering services such as drains
or electricity.
The Garden Gym does not accept any liability in relation
to the installation and subsequent use of the gym
relating to incorrect or improper installation.
You will need
Spade / hole diggers / safety gloves / step ladder / tape /
measure / level / 2 x 19mm socket drivers / hammer
Post mix
Between 1 and 2 bags per post, depending on
the size of your holes and ground conditions
Monkey bar
Installation guide
NB- Before you start!
Ensure that the first pull up bar is solid. You will connect the
monkey bar to the original pull up bar which will can create
movement in the foundations. We recommend that you let the
pull up bar concrete harden before starting to add the monkey
bar. Depending on the mix you used this would be between 2-4
hours.

Monkey bar
Installation guide
Caution
When deciding on your gym layout it is essential to ensure that the monkey bar has at least one 90-degree connection
to a pull up bar. Also, if using a pull up bar at each end then the layout must be in a zig-zag style (see picture A). The
images above show some correct layouts (also see next page)
Picture A

Monkey bar
Installation guide
Picture A These images show the
correct orientation of
the monkey bar and pull
up bar. The monkey bar
must be positioned on
the opposite side of the
upright post.
These images show
the incorrect
orientation of the
monkey bar and pull
up bar
Caution Monkey bar must be orientated as shown or
injury could occur

1
Monkey bar
Installation guide
3
2
4
Digging the holes
Digging the holes for the posts is a key part of the installation.
The hole must be a minimum of 600mm deep (700mm for 3.6m
posts). You will notice that the post has a 12mm hole on the
lower section, this is to take the supplied metal bar which is to be
inserted prior to concreting. Ensure that the hole is large enough
to take this bar. Leave plenty of space for alignment.
Build the monkey bar
Insert the 8 metal bars into the wooden monkey post, secure in
place with the bolt, washers and nut, insert the supplied bungs
into the ends of the metal bars, you can also insert all of the
bungs into the holes in the wooden post. NB if the bars are
slightly loose use a small amount of electrical tape to wrap
around the bar to achieve a snug fit.
Layout the monkey bar
Taking notice of the offset
scallop detail use the
monkey bar to work out
the position of the support
post. You can fit the
monkey bar to either
upright of the pull up bar.
When you have marked
the position of the upright
you can dig the hole (min
600mm deep)
Reinforcing rods
We supply metal rods to Provide additional support to the
foundation. Insert the rod through the hole in the post prior
to placing in the hole

5
Monkey bar
Installation guide
7
6
8
Insert the post in the hole
You can insert the post in
the hole and create a
suitable brace to hold in
position. Take care here as
the post will be concreted
in later to allow you to
level and align the monkey
bar. Lift into place
It is necessary that a minimum of 2 people carry out his stage as the
monkey bar will weigh apx. 50kg. The monkey bar will need to be lifted
into position and the coach bolts and nuts used to secure it into position
to the upright posts, the bolts will be tightened later. You can use a
suitable strap to hold in place while you add the nuts and bolts
Fixing the coach bolts
The coach bolts will need to be firmly hammered into the monkey
bar, this ensures the bolt will not rotate when tightening, this is very
important!
Levelling and alignment
Ensure everything is secure (not fully tightened) and take your time
to level everything, the braces can be left in place until the
installation is finished

Monkey bar
Installation guide
9
Concrete and tighten
When everything is levelled and square you can concrete the
upright in place and then when the concrete hardens tighten all
of the bolts and insert the hole caps.
Foundations
The stability of your Gym relies on correct installation of the posts.
We recommend a minimum depth of 600mm. Ensure the concrete
is fully hardened before use (2-3 days) and the hole is suitable for
the ground conditions and planned usage. We also recommend
using a small amount of pea shingle at the base of the post to aid
drainage.
Maintenance
All of our materials are maintenance free, the posts are supplied
with a tanalised finish and 10 year life expectancy. It is essential to
check the bolts and fixings on a monthly basis and tighten where
necessary as they can loosen off as the timber goes through the
natural drying process.
Train Safe!
1.Always consult your doctor before undertaking any physical exercise.
2.Injuries to health may result from excessive, incorrect training or using
the equipment in a way that it is not designed for.
3.Remove jewellery, watches or anything else that may catch or snag
before exercising.
4.Always warm up prior to exercising, if you are unsure consult a health
professional for advice.
5.Children should not be allowed to use the equipment without the
strict supervision of adults who are aware of how to exercise correctly.
6.Our products have been designed to carry out exercise and are not
meant as a climbing frame or piece of play equipment. The user is
wholly responsible for any accidents or injuries occurring from usage of
the equipment regardless of proper or improper usage.
7.The Garden Gym ltd disclaims all liability from the mis-use or incorrect
installation of our products.
8.The user must not adapt, amend or remove any part of the
equipment.