Thermoheat LPFA40L User manual

GENERAL HAZARD WARNING
FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH
THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS,
OR DAMAGE FROM THE HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON
MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD
USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTION
MANUAL, LABELS, ETCETERA, CONTACT THE MANUFACTURER.
CONSUMER: Retain this manual for future reference.
Printed in China IMLPFL - KED
USER’S MANUAL AND OPERATING INSTRUCTIONS
PROPANE
CONSTRUCTION HEATER
LPFA40L (40,000 BTU/HR, FORCED - AIR)
LPFA60L (30,000/60,000 BTU/HR, FORCED - AIR)
LPFA125L (70,000/125,000 BTU/HR, FORCED - AIR)
LPFA150L (120,000/150,000 BTU/HR, FORCED - AIR)
MODELS:
C US
ANS Z83.7-2011 CSA 2.14-2011
Adequate ventilation must be provided.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 877-447-4768 8:30 a.m. – 4:30 pm CST, Monday – Friday
or email us at [email protected]
www.ghpgroupinc.com

Introduction & Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
• General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
• Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
• Unpacking Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
• Size & Capacity Of Propane Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Installation To The Propane Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Relling The Propane Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Leak Checking & Positioning Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
• Lighting & Shutdown Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9
• Test Firing Heater & Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
• Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 12
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16
PROPANE CONSTRUCTION HEATER ILLUSTRATED / PARTS BREAKDOWN:
FA40 Series / FA60 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FA125 Series / FA150 Series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TABLE OF CONTENTS
WARNING: NOT FOR HOME OR RECREATIONAL VEHICLE USE.
WARNING
: FIRE, BURN, INHALATION, AND EXPLOSION HAZARD, KEEP SOLID
COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE
DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS.
NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR
AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT
THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.
PROPANE CONSTRUCTION HEATER
WARNING
This product and the fuels used to operate this product (liquid propane), and the products of
combustion of such fuels, can expose you to chemicals including benzene, which is known to the
State of California to cause cancer and reproductive harm.
For more information go to www.p65Warnings.ca.gov
WARNING
: Using this heater in a residential garage requires that the heater is positioned
so that it is protected against any possible damage by a moving vehicle, etc. It must be
positioned so that the base of the heater is no less than 18 in (450 mm) above the garage oor or
8 ft (2450 mm) in repair garages. The heater must be placed on a stable surface. Do not place it on
a chair, ladder, etc. Raising the heater will reduce BUT NOT eliminate the possibility of lighting the
vapor of any ammable liquids which may be improperly stored or accidentally spilled. If the smell of
gasoline is present, DO NOT operate this heater until the area has been properly ventilated.
WARNING: CONSTRUCTION HEATERS ARE NOT FOR USE IN
GARAGES IN CANADA.
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
2 3

The heater is designed and approved for use as a construction heater under ANS Z83.7 CSA 2.14. It is hard
to anticipate every use which may be made of this heater. CHECK WITH YOUR LOCAL FIRE SAFETY
AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.
PROPANE FORCED AIR CONSTRUCTION HEATERS
This is a direct-red forced air construction heater for either indoor construction or outdoor use. Its intended
use is primarily the temporary heating of buildings or structures under construction, alteration or repair. All the
products of combustion generated by the heater are forced through the heater and released into the area being
heated. This heater operates at approximately 98%+ combustion efciency but still produces a small amount
of carbon monoxide. Humans can tolerate small amounts of carbon monoxide for short periods. Carbon
monoxide can build up in a heated space and failure to provide adequate ventilation could result in poisoning
or death.
PROPANE CONSTRUCTION HEATER
2 3
Other standards govern the use of fuel gases and heat producing products in specic applications.
Your local authority can advise you about these.
IMPORTANT: READ THIS USER’S MANUAL CAREFULLY AND COMPLETELY BEFORE TRYING
TO OPERATE OR SERVICE THIS HEATER. IMPROPER USE OF THIS HEATER CAN CAUSE
SERIOUS INJURY OR DEATH FROM FIRE, EXPLOSION AND CARBON MONOXIDE POISONING.
SPECIFICATIONS
WARNING
: NOT FOR USE WITH DUCT WORK.
40,000BTU/hr
30,000BTU/hr
60,000BTU/hr
70,000BTU/hr
125,000BTU/hr
120,000BTU/hr
150,000BTU/hr
Propane Propane Propane Propane
CylinderPressure CylinderPressure CylinderPressure CylinderPressure
5psig 5psig 5psig 5psig
11"W.C 11"W.C 11"W.C 11"W.C
1.9lbs/hr0.86kg/hr
1.4lbs/hr0.63kg/hr
2.8lbs/hr1.27kg/hr
3.3lbs/hr1.5kg/hr
5.8lbs/hr2.63kg/hr
5.6lbs/hr2.54kg/hr
7.0lbs/hr3,18kg/hr
120V,60Hz,1Ø 120V,60Hz,1Ø 120V,60Hz,1Ø 120V,60Hz,1Ø
Amperage Load 0.68amps 0.65amps 0.7amps 0.7amps
Fan
Unload
Load
3550rpm
3000rpm
3570rpm
3300rpm
3580rpm
3300rpm
3580rpm
3300rpm
Piezo/ManualSpark ContinuousSpark ContinuousSpark ContinuousSpark
0.16"(4mm) 0.16"(4mm) 0.16"(4mm) 0.11"(2.8mm)
19.3"x8.3"x15.2"
(49.0x21.1x38.6)cm
19.3"x8.3"x15.2"
(49.0x21.1x38.6)cm
25.6"x11.8"x16.1"
(65.0x30.0x40.9)cm
25.6"x11.8"x16.1"
(65.0x30.0x40.9)cm
InputRating
TypeofGas
GasSupplyPressureto
RegulatorMaximum
Minimum(forpurposeof
InputAdjustment)
Size(LxWxH)
ManifoldPressure
GasConsumption
ElectricalInput
Ignition
SparkGap
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

Accidents are always tragic especially because so many of them could have been prevented with little care
and judgment. There are some basic good practices, we hope you will follow for safe use of your heater.
• Children should be carefully supervised, when they are in the area.
• Always maintain proper clearance from combustible materials. Minimum clearance from combustibles:
Side - 24” (61 cm); Top - 36” (92 cm); Front - 72” (183 cm). Floor - combustible. Not for use on nished oors.
• Heater must be placed on level and stable surface.
• Never place anything including clothes or other ammable items on the heater.
• The appliance area shall be kept clear and free from combustible materials, gasoline and other ammable
vapours and liquids.
• Do not modify or operate a heater which has been modied.
• Adequate clearance for accessibility and for combustion & ventilation air supply must be maintained at all
times when the heater is operating.
• Service and repair should be done by a qualied service person. The heater should be inspected
before each use and at least annually by a qualied person. More frequent cleaning may be required as
necessary. Do not service while hot or operating.
• Never connect heater to an unregulated gas supply.
• The heater is shipped from the factory for LP(Propane) gas. This heater is for use with propane gas only,
do not convert heater to any other gas. Installation must conform to local codes or, in the absence of local
codes, with the standard for the Storage and Handling of Liqueed Petroleum Gases ANSI/NFPA 58 and the
Natural Gas and Propane Installation Code CSA B149.1
• The minimum and maximum inlet pressures to the regulator from the gas tank are 5 psi and bottle pressure,
respectively. Use only the regulator & hose assembly provided with the heater. Inspect the regulator/hose
assembly prior to each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with
regulator/hose assembly listed on the parts list prior to using this heater.
• Gas supply connections should be checked using a 50/50 solution of liquid dish soap and never use a ame
to check for gas leaks.
• The electrical connection & grounding must comply with National Electrical Code. ANSI/NFPA 70 or in
Canada CSA C22.1, Canadian Electrical Code, Part 1. Use only a properly grounded three
(3) prong receptacle.
• Do not restrict inlet or outlet by any means. The ow of combustion and ventilation air is not to be obstructed.
• This heater should not be directed toward any propane-gas container within 20 ft (6M). The heater must be
located at least 6 ft. (1.83 m) in the U.S.; or (ii) 10 ft. (3 m) in Canada, from any propane gas container.
• The propane cylinder supply system must be arranged to provide for vapour withdrawal from the
operating cylinder.
• This heater is not to be used with external thermostats, timers or other devices that control or alter electrical
supply to the heater.
PROPANE CONSTRUCTION HEATER
PRODUCT FEATURES
• Portable & Stable • 100% Safety Shutoff System
• Wind Resistant & Rain Protected • Continuous Adjustable Input Ratings
• Continuous Spark Ignition or (Except FA40)
Piezo Electric Spark Ignition
GENERAL SAFETY INSTRUCTION
IMPORTANT SAFETY INSTRUCTION
WARNING
: Motor and fan must be running before lighting, during operation and at shutdown,
in order to prevent a ame-out condition which could result in personal injury or property damage.
Assembly Components and Instructions for Steel Base Units:
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
4 5

PROPANE CONSTRUCTION HEATER
UNPACKING HEATER
1. Remove heater from carton.
2. Remove all protective packing applied to heater for shipment.
3. Retain cartons and packaging material until unit is operated and found in good condition.
4. Check heater for any shipping damage. If heater shows any external or internal
damage, promptly inform dealer/distributor where you purchased heater.
Assembly Components and Instructions for Steel Base Units:
Tighten, clockwise,
use a wrench
Hose Assembly
Assembly Time:
5 Minutes
Contents:
All Models: Unit, Manual, Hose and Regulator
Assembly
FA100 - FA150 Series Includes:
2 Cord Wrap Attachments, 4 Screws (ST3.5x10)
Tools required for assembly:
All Models: Adjustable Wrench
FA100 - FA150: Phillips Head
Screw Driver
1. Assembling the Cord Wrap Attachments:
(FA100 - FA150 Series Only)
Parts Required:
4 Screws (ST3.5x10),
and 2 Cord Wrap Attachments
Place the cord wrap attachment
as shown, then use Phillips
screwdriver to tighten the
screws and secure the
cord wrap attachments.
2. Regulator and Hose Connection:
(All Models)
See gure on right.
Connect the hose tightly to
the heater using a wrench.
Please also refer to
page 8 in the manual.
4 5
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

PROPANE CONSTRUCTION HEATER
INFORMATION ON SIZE * CAPACITY OF PROPANE GAS CYLINDERS:
The chart below shows the number and size of propane tanks needed to run this heater.
*Less gas is vaporized at lower temperatures.
You may need two or more 100 pound (45 kg) tanks or one larger tank in colder weather.
(See the parts list for your model of heater to get the specied regulator assembly.)
The propane (LP) gas tank must also be equipped with the following:
• A collar to protect the Propane gas valve.
• A shutoff valve terminating a Propane gas cylinder valve outlet as specied in the
American National Standards for Compressed Gas Cylinder Valve Outlets and Inlet
Connections.
• A safety relief valve having direct communications with the vapor space of the tank.
• An arrangement of vapor withdrawal.
The propane (LP) gas pressure regulator and hose assembly supplied with
this heater must be used without alteration.
The hose assembly shall be visually inspected prior to each use of the heater. If it is evident
that there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the
heater being put into operation. The replacement hose assembly shall be that specied
by the manufacturer.
Number of Tanks
Temperature
(°F-°C) at
tank 40,000-60,000 BTU/h 100,000 -
125,000 BTU/h 150,000 BTU/h
1 - 20lb (9kg) 2 - 100lb (45kg) 2 - 100lb (45kg)
1 - 20lb (9kg) 2 - 100lb (45kg) 2 - 100lb (45kg)
1 - 20lb (9kg) 2 - 100lb (45kg) 3 - 100lb (45kg)
1 - 20lb (9kg) 3 - 100lb (45kg) 3 - 100lb (45kg)
2 - 20lb (9kg) Use Larger Tank Use Larger Tank
1 - 100lb (45kg) Use Larger Tank Use Larger Tank
Above
32°F (0°C)
32°F (0°C)
20°F (-7°C)
10°F (-12°C)
-10°F (-23°C)
-20°F (-29°C)
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
6 7

Propane/LP
Supply Valve
Propane/LP
Tank
Regulator
Fuel Gas
Fitting Hose to
Heater
PROPANE CONSTRUCTION HEATER
INSTALLATION TO THE PROPANE GAS TANK
IMPORTANT: You must use a propane/LP gas supply cylinder that is compatible with the connection device
provided with the hose and regulator.
REFILLING THE PROPANE GAS TANK
ALL NEW CYLINDERS MUST BE PURGED BEFORE THE FIRST FILLING.
• Turn heater gas valve knob and gas tank valve to OFF position.
• Propane tank valve equipped with the old style tting has LEFT HANDED THREADS. Turn POL tting
CLOCKWISE to loosen. Protect POL tting when disconnected from tank.
• Have tank lled by your local Propane gas supplier.
• Fasten full Propane tank and connect POL tting to tank valve by turning COUNTERCLOCKWISE.
• With heater gas valve knob still in the OFF position, turn ON tank valve and check for leaks
with soap solution.
WARNING
: Purging and lling of LP gas tanks must be performed by personnel who
has been thoroughly trained in accepted LP gas industry procedures. Failure to follow
these instructions may result in explosion, re, severe personal injury, or death.
1. Provide propane/LP supply system. Ensure that the valve on the cylinder is fully closed by turning the knob
fully clockwise ( ). Ensure that the cylinder is fully upright for vapor withdrawl. (see size/capacity, page 7).
2. Connect hose to heater inlet. Tighten rmly using a wrench. You must use the regulator supplied with heater.
3. Connect fuel gas tting hose/regulator assembly to propane LP tank(s).
3a. For units with a POL tting (see gure 1) turn fuel tting counterclockwise into threads on tank. Tighten
rmly using a wrench. Some models have a hand wheel that can be used to tighten the tting. This hand
wheel can be slid off of the nut so that a wrench can also be used to tighten the tting. IMPORTANT:
Position regulator so that hose leaving the regulator is in a horizontal position.
3b. For units with a QCC tting (see gure 2) turn QCC gas tting clockwise onto threads on tank. Tighten
rmly using your hand (DO NOT USE A WRENCH). IMPORTANT: Position regulator so that the regulator
vent is pointing down toward the oor and the arrow on the regulator is visible.
4. Open propane/LP supply valve on propane/LP tank(s) slowly. NOTE: If not opened slowly, excess ow
device in regulator may stop gas ow. If this happens, close propane/LP supply valve, wait one minute
(or until you hear a click) and open again slowly.
5. Check all connections for leaks. Apply a 50/50 solution of liquid dish soap and water to gas joints.
Bubbles forming show a leak that must be corrected.
6. Close propane / LP supply valve before attempting to repair connection.
Connector Inlet
Hose to Regulator
Hose Fitting
FIGURE 1 FIGURE 2 FIGURE 3
6 7
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

PROPANE CONSTRUCTION HEATER
PROPANE SAFETY
Propane is safe to use when properly handled. Careless handling of the Propane gas tank could
result in re and/or an explosion. Therefore:
• Always keep tank/cylinder securely fastened in an upright position.
• Avoid tipping tank on its side when connected to a regulator since this may cause damage to
diaphragm in regulator.
• Handle valves with care.
• Never connect an unregulated Propane tank to construction heater.
• Do not subject Propane tank to excessive heat.
• Tightly close the gas shutoff valve on the Propane tank after each use.
• The POL tting must be protected when disconnected from the propane tank.
• Never store a Propane gas tank inside a building or in the vicinity of any gas burning appliance.
THE DISCONNECTED TANK MUST NEVER BE STORED IN A BUILDING, GARAGE
OR ANY OTHER ENCLOSED AREA.
LEAK CHECKING
Check all gas connections with a soap solution to be sure they are tight and leak proof.
• The installation of your heater must meet all local codes and/or gas utility requirements or, in the
absence of local codes, with the Storage and Handling of Liqueed Petroleum Gases, ANSI/ NFPA
58 and the Natural and Propane Installation Code, CSA B149.1.
• The minimum clearances to combustible construction: Side - 24” (61 cm); Top - 36” (92 cm);
Front - 72” (183 cm); Floor - combustible, must be maintained at all times.
• The hose assembly should be visually inspected prior to each use of the heater. If it is evident that
there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being
put into operation.
• The replacement hose assembly shall be that specied by the manufacturer (Refer to parts list).
LIGHTING INSTRUCTIONS
WARNING
: Motor and fan must be running before lighting, during operation and shutdown, in
order to prevent a ame-out condition which could result in personal injury or property damage.
NOTE: This heater uses a continuous spark ignition system. This unit will continue to make a clicking/
ticking sound at all times before ignition, after ignition and during operation, regardless of valve knob
positioning.
1. Connect power cord to a properly grounded three (3) prong 120V, 60Hz, single phase receptacle.
2. Turn gas valve knob clockwise to OFF position.
3. Wait ve (5) minutes to clear any gas. Then smell for gas, if you don’t smell gas, go to next step.
4. Turn gas supply ON by turning Propane tank valve counterclockwise .
5. Push in and turn gas control knob counterclockwise to “LOW/IGN”. This will light the burner. If
needed, keep pressing control knob until the burner lights and keep depressing and turning from
OFF to LOW/IGN on Piezo electric spark models. (“HIGH/IGN”: In case of FA40 series)
6. Keep the valve knob depressed for at least 30 seconds after lighting the burner. After 30 seconds
release valve knob.
7. If burner does not stay lit, repeat the lighting procedure.
8. When burner is lit, turn gas valve knob counterclockwise to desired setting. (All models, except
FA40 series).
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
8 9

PROPANE CONSTRUCTION HEATER
SHUTDOWN INSTRUCTIONS
TEST FIRING HEATER
Test re your construction heater, following the lighting instructions applicable to the gas control sys-
tem employed. Leak test all gas connections with soap solution. Soap bubbles indicate gas leakage.
DO NOT use a match or ame to test for gas leaks.
STORAGE
Never store a Propane gas tank inside a building or in the vicinity of any gas or oil burning appliance.
When the Propane tank is not disconnected from the construction heater, the gas tank and heater
must be stored outdoors in a well ventilated area, out of the reach of children. If for any reason the
heater is to be stored indoors, the tank must be disconnected and stored outdoors in a well ventilated
area out of reach of children, in accordance with the standard for the the Storage and Handling of
Liqueed Petroleum Gases, ANSI / NFPA 58 and CSA B149.1, Natural Gas and Propane Installation
Code. The plastic tank valve plug supplied with your tank must be tightly installed when the tank is
disconnected from the heater.
MAINTENANCE INSTRUCTIONS
1. Turn unit off, allow heater to fully cool and disconnect propane hose before performing any Mainte-
nance
functions. Unplug the unit from the 120V receptacle.
2. Keep unit clean and keep the inside of the torpedo housing debris free.
3. Have unit checked by a qualied technician at least once a year, preferably prior to the heating
season.
WARNING
: Motor and fan must be running before lighting, during operation and at shutdown,
in order to prevent a ame-out condition which could result in personal injury or property damage.
Turn gas valve knob clockwise to OFF position.
Turn gas supply OFF by turning Propane tank valve clockwise to close.
Disconnect the power cord once the heater has cooled to ambient temperature.
REPLACEMENT PARTS
Warning: Use only original replacement
parts. This Heater must use design-specic
parts. Do not substitute or use generic parts.
Improper replacement parts could cause
serious or fatal injuries.
This will also protect your warranty coverage
for parts replaced under warranty.
Parts warranty and non-warranty: Contact
authorized dealers of this product. If they can
not supply original replacement part(s), either
contact your nearest Parts Central or World
Marketing of America at 1-800-776-9425.
When calling World Marketing, have ready:
• your name
• your address
• how heater was malfunctioning
• serial number of heater
• model number of heater
• replacement part number
8 9
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

Always be sure to follow proper maintenance procedures, by cleaning the heater once per
month during regular usage, and check spark gap at least once per season.
     
 




     
 




     
 
   

   
   
     

   
   
     
  

   
   
TROUBLESHOOTING:
PROBLEM POSSIBLECAUSE CORRECTIVEACTION
TROUBLESHOOTING
PROPANE CONSTRUCTION HEATER
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
10 11

PROPANE CONSTRUCTION HEATER
WIRING DIAGRAMS
PROPANE CONSTRUCTION HEATER
10 11
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

WIRING DIAGRAMS
*
*100K,125K & 150K Models only
*100K,125K & 150KSólo modelos
*100K,125K & 150K Les modèles Seulement
*
*
PROPANE CONSTRUCTION HEATER
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
12 13

MODELS: LPFA40L
LPFA60L
REPLACEMENT PARTS LIST
PROPANE CONSTRUCTION HEATER
12 13
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

LPFA40L LPFA60L
1INNER SHELL ASSEMBLY 12304818 2304818
2NOZZLE 1*2304829 *2325121
3FLAME CAP 12304819 2325120
4THERMAL SWITCH BRACKET 12304826 2304826
5THERMAL SWITCH 12201373 2201599
6NOZZLE NUT 12304578 2304578
7SPARK PLUG ASSEMBLY 12201375 2206033
8THERMOCOUPLE ASSEMBLY (1130/1474-425L) 12304885 2304885
9GAS TUBING ASSEMBLY 12304830 2304830
10 OUTER SHELL 1FA40-01(B) FA40-01(B)
11 CORD WRAP (select models only) 2N/A N/A
12 HANDLE ASSEMBLY - GRAY 12305426 2305426
12.1 SCREW - HANDLE FRONT 12001355 2001355
12.2 SCREW - HANDLE FRONT 12001077 2001077
12.3 NUT - HANDLE REAR 12000384 2000384
13 MOTOR SUPPORT 12304823 2304823
13.1 MOTOR - MOUNTING BOLT 22001332 2001332
13.2 SLEEVE 12304949 2304949
14 MOTOR ASSEMBLY 12305909 2304547
14.1 MOTOR - FAN 12304821 2304821
15 FAN GUARD - BLACK 12304828 2304828
16 MOTOR BRACKET 12304937 2304937
17 VALVE - GAS 1
GS22-FA40 GS22A-FA60
18 PRESSURE SWITCH 1
N/A N/A
19 VALVE BRACKET 12304624 2304624
20 BASE ASSEMBLY - BLACK 12304923 2304923
21 POWER CORD ASSEMBLY 12201368 2101670
22 GAS CONNECTOR INLET 12304831 2304831
23 CAPACITOR 12201372 2201372
24 BASE LOWER -BLACK 12304925 2304925
25 KNOB GAS VALVE - BLACK 12101451 2101451
26 HEIGHT CONTROLLER - BLACK 12304927 2304927
27 HEIGHT CONTROL SCREW - BLACK 12304510 2304510
28 LEAD WIRE ASSEMBLY 12201371 2201371
29 SPARK MODULE 1N/A 2201391
30 PCB ASSEMBLY 12201369 2201369
REG & HOSE ASSEMBLY - 10FT (3M) 1KR10602-10-31 KR10602-10-31
REG & HOSE ASSEMBLY - 10FT (3M) w/HANDWHEEL 1KR10602-HW10-31 KR10602-HW10-31
REG & HOSE ASSEMBLY (QCC) - 10FT (3M) 1KR10602-HW10-31 KR10602-HW10-31
REG & HOSE ASSEMBLY -15FT (4.6M) 1KR10602-15-31 KR10602-15-31
REG & HOSE ASSEMBLY -15FT (4.6M) w/HAND WHEEL 1KR10602-HW15-31 KR10602-HW15-31
REG & HOSE ASSEMBLY (QCC) - 15FT (4.6M) 1TYQ-9C-4572 TYQ-10C-4572
* VERSION NOT SHOWN IN EXPLODED VIEW
31
ITEM No.
DESCRIPTION
QTY
PART NUMBER
PROPANE CONSTRUCTION HEATER
REPLACEMENT PARTS LIST
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
14 15

MODELS: LPFA125L
LPFA150L
PROPANE CONSTRUCTION HEATER
PROPANE CONSTRUCTION HEATER ILLUSTRATED / PARTS BREAKDOWN
14 15
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!

LPFA125L LPFA150L
1INNER SHELL ASSEMBLY 12304929 2304929
2NOZZLE 15030077 2304944
3FLAME CAP 12325122 2304931
4THERMAL SWITCH BRACKET 12315515 2001355
5THERMAL SWITCH 12201373 2201373
6NOZZLE NUT 12304945 2304945
7SPARK PLUG ASSEMBLY 12206034 2201393
8THERMOCOUPLE ASSEMBLY (1130/1474-425L) 12304885 2304885
9GAS TUBING ASSEMBLY 12325138 2304947
10 OUTER SHELL 1FA125-01(B) FA125-01(B)
11 CORD WRAP (select model s only) 22101423 2101423
12 HANDLE ASSEMBLY - GRAY 12305426 2305426
12.1 SCREW - HANDLE FRONT 12001355 2001355
12.2 SCREW - HANDLE FRONT 12001077 2001077
12.3 NUT - HANDLE REAR 12000384 2000384
13 MOTOR SUPPORT 12304823 2304823
13.1 MOTOR - MOUNTING BOLT 22001332 2001332
13.2 SLEEVE 12304949 2304949
14 MOTOR ASSEMBLY 12304548 2304548
14.1 MOTOR - FAN 12304936 2304936
15 FAN GUARD - BLACK 12304939 2304939
16 MOTOR BRACKET 12304938 2304938
17 VALVE - GAS 1GS22A-FA125 GS22A-FA150
18 PRESSURE SWITCH 1
2305976 2305976
19 VALVE BRACKET 12304624 2304624
20 BASE ASSEMBLY - BLACK 12304924 2304924
21 POWER CORD ASSEMBLY 12101673 2101673
22 GAS CONNECTOR INLET 12304831 2304831
23 CAPACITOR 12301390 2301390
24 BASE LOWER - BLACK 12304926 2304926
25 KNOB GAS VALVE - BLACK 12101451 2101451
26 HEIGHT CONTROLLER - BLACK 12304928 2304928
27 HEIGHT CONTROL SCREW - BLACK 12304510 2304510
HEIGHT CONTROL SCREW - ORANGE 12305467 N/A
28 LEAD WIRE ASSEMBLY 12201371 2201371
29 SPARK MODULE 12201391 2201391
30 PCB ASSEMBLY 12201369 2201369
REG & HOSE ASSEMBLY - 10FT (3M) 1GR109-10-38 GR109-10-38
REG & HOSE ASSEMBLY - 10FT (3M) w/HANDWHEEL 1GR109-HW10-38 GR109-HW10-38
REG & HOSE ASSEMBLY(QCC) - 10FT (3M) 1TYQ-6D1-3000 TYQ-6E1-3000
REG & HOSE ASSEMBLY -15FT (4.6M) 1GR109-15-38 GR109-15-38
REG & HOSE ASSEMBLY -15FT (4.6M) w/HAND WHEEL 1GR109-HW15-38 GR109-HW15-38
REG & HOSE ASSEMBLY(QCC) -15FT (4.6M) 1TYQ-6D1-4572 TYQ-6E1-4572
* VERSION NOT SHOWN IN EXPLODED VIEW
ITEM
No.
DESCRIPTION
QTY
PART NUMBER
31
* VERSION NOT SHOWN IN EXPLODED VIEW
PROPANE CONSTRUCTION HEATER
REPLACEMENT PARTS LIST
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
16

WARRANTY
LIMITED WARRANTY:
DUTIES OF THE OWNER:
This heating appliance must be operated in accordance with the written instructions furnished with this heater. This warranty shall not excuse
the owner from properly maintaining this heater in accordance with the written instructions furnished with this heater. A bill of sale, canceled
check or payment record must be kept to verify purchase date and establish warranty period. Original carton should be kept in case of warranty
return of unit.
WHAT IS NOT COVERED:
1. Damage resulting from use of improper fuel.
2. Damage caused by misuse or use contrary to the owners manual and safety guidelines.
3. Damage caused by a lack of normal maintenance.
4. Fuses
5. Use of non-standard parts or accessories.
6. Damage caused in transit. Freight charges on warranty parts or heaters to and from the factory shall be the responsibility of the owner.
This warranty does not imply or assume any responsibility for consequential damages that may result from the use, misuse, or the lack of
routine maintenance of this heating appliance. A cleaning fee and the cost of parts may be charged for appliance failures resulting from lack of
maintenance. This warranty does not cover claims which do not involve defective workmanship or materials. FAILURE TO PERFORM
GENERAL MAINTENANCE (INCLUDING CLEANING) WILL VOID THIS WARRANTY.
THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. THE
REMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES. IN NO EVENT WILL
GHP GROUP, INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
CLAIMS HANDLED AS FOLLOWS:
1. Contact your retailer and explain the problem.
2. If the retailer is unable to resolve the problem, contact our Customer Service Dept. detailing the heater model, the problem, and proof
of date of purchase.
3. A representative will contact you. DO NOT RETURN THE HEATER TO GHP GROUP,INC. unless instructed by our Representative.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
TO REGISTER THE WARRANTY ON YOUR HEATER, PLEASE FILL OUT THIS CARD COMPLETELY
AND MAIL WITHIN 14 DAYS FROM DATE OF PURCHASE OR REGISTER ON-LINE AT www.ghpgroupinc.com
NAME: ______________________________________ PHONE: ( ) __________________ EMAIL: ____________________________
ADDRESS: _________________________________ CITY: ______________________________ STATE: __________ ZIP: ____________
MODEL: ____________________ SERIAL #: _______________________________________ DATE PURCHASED: __________________
DEALER PURCHASED FROM: ____________________________________________ TYPE OF STORE: __________________________
CITY & STATE WHERE PURCHASED: ______________________________________________ PRICE PAID: _______________________
Please Take a Minute To Give Us Your Answers To The Following Questions.
All Responses Are Used Solely For Market Research And Are Held In Strict Confidence.
Who primarily decided this purchase? Male Female 18-24 25-39 40-59 60 and over
Purpose of Purchase? _______________________________________________________________________________________________
Do you own any other portable heaters? Yes No If yes, type____________________________brand_____________________
How do you intend to use your new heater? Construction Site Farm Warehouse/Commercial Garage/Outbuilding Other
How did you become aware of this heater? In-Store Display Newspaper Ad Magazine Ad Friend/Relative
TV Commercial Store Salesperson Other ___________________________
What made you select this heater? Style Size/Portability Price Package Brand Other ___________________
Do you: own rent Would you recommend this heater to a friend? Yes No
Please give us your comments:________________________________________________________________________________________
THANK YOU FOR COMPLETING THIS FORM!
Information will be held confidential.
This limited warranty is extended to the original retail purchaser of this Forced Air/Convection/Radiant Heater and warrants against any defect
in materials and workmanship for a period of one (1) year from the date of retail sale (lifetime warranty for the brass nozzle burner only). GHP
Group, Inc., at it’s option, will either provide replacement parts or replace or repair the unit, when properly returned to the retailer where
purchased or one of our service centers as directed by GHP Group, Inc., within one (1) year of retail purchase. (Shipping costs, labour costs,
etc. are the responsibility of the purchaser.)
PROPANE CONSTRUCTION HEATER
16

WARRANTY REGISTRATION
IMPORTANT: We urge you to fill out your warranty registration card within fourteen (14)
days of date of purchase. You can also register your warranty on the internet at
www.ghpgroupinc.com. Complete the entire serial number. Retain this portion of the card
for your records.
SAVE THIS CARD!
Place
Postage
Stamp
Here
GHP Group, Inc.
8280 Austin Avenue
Morton Grove, IL 60053-3207
GHP Group, Inc.
8280 Austin Ave.
Morton Grove, IL 60053-3207
Tel: [phone]
www.ghpgroupinc.com
8280 Austin Avenue
Morton Grove , IL.
6 0 053-3207
Tel: ( 847 ) 324 - 5900
Fax: ( 847 ) 324 - 5901
Toll Free (877) GHP Group
( 8 7 7 ) 44 7 - 4 7 6 8
www.ghpgroupinc.com
GHP
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302
Tel: [phone]
www.ghpgroupinc.com
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302