THOR 28096T User manual

USER GUIDE - 28096T
42-100"
Tilt Slim TV Wall Mount
• TV Size range: 42-100"
• Maximum weight capacity: 50kg
• Mount function: Tilt
• Wall to TV distance: 40mm
• Compatible with VESA sizes:
200 x 200, 300 x 300, 300 x 200, 400 x 200,
400 x 300, 400 x 400, 600 x 400
Components
Before installation check that you have all the components shown here and
that none of them are damaged.
WARNING
x1
A
2
1
Wall Mount & VESA Compatibility
• VESA is the standard adopted by most TV manufacturers
for wall bracket mounting.
• There are 4 holes on the back of every at screen TV and the space
between the holes is governed by the VESA standard.
• VESA comes in a range of sizes depending on the weight and size of the at
screen TV; sizes 50 x 50mm, 75 x 75mm, 100 x 100mm, 200 x 100mm and
so on... are standard. Not all at screen TVs are compliant, contact the
TV manufacturer for assistance if your TV does not appear to comply
with VESA.
• To check if your TV or monitor is compliant, look at the rear of the display
there should be 4 screw-holes in a square pattern or in larger displays
a rectangular shape.
• Measure the distances marked (2) (horizontal) x (1) (vertical)
below in mm to nd your VESA format.
• We have not supplied wall xings
with this product. All walls differ
in strength and thickness.
Consult a qualied installer or seek
advice from your local DIY/hardware
store on purchasing suitable wall
xings to safely mount the bracket
on the type of wall being used.
• Check the components list and images
to check there are no missing
or defective parts.
• Never exceed the Maximum
Weight Capacity.
• Read these instructions carefully
before installation. If in any doubt
about safely installing this product,
contact a professional installer
for assistance.
• This product was designed to be
installed on wood stud walls and solid
concrete/brick walls. When xing to
walls screws/bolts should be xed into
bricks/stone not into mortar courses.
• Make sure the wall will support the
combined load of the equipment and
hardware. Also check for hidden
wiring or plumbing.
• Make sure that the heads of the
screws/bolts you buy as wall
fastenings are the correct size to hold
the bracket securely in position.
• For larger/heavier TVs we recommend
that you ask someone to assist you
with lifting and positioning your TV.
• This product is suitable for indoor
use only.
• Improper installation or use of this
product can result in product failure,
damage or personal injury.
• This product contains small items
that could cause choking if swallowed,
so keep these items away from
children and pets.
• Appropriate safety equipment and
proper tools must be used
for installation.
Always check
manufacturer’s operating and safety
instructions before using tools
and other equipment .
M5 x 14 (x4)M-A M-B M-C
M8 x 30 (x4)M-D
M-G M-H
M-E
(x8) (x8)
M8 x 50 (x4)
M6 x 14 (x4) M6 x 30 (x4)
D
G H
J K
E
M-F (x4)
I
F
M-I
L
x1
B
x1
C

The process is the same as for attaching to wood see Fig.1. You will
however need to use suitable screws/bolts/wall plugs for the type of wall you
are mounting onto (if in doubt ask for advice at your local DIY/hardware store and
remember to make sure that the heads of the screws/bolts are the correct size
to hold the bracket securely in position). When xing to walls screws/bolts should
be xed into bricks/stone not into mortar courses.
1a. Preparing Wall Fixings - Stud Walls
Tools required
1b. Preparing Wall Fixings - Concrete/Brick Walls
Tools required
Select the correct size bolts to t the VESA holes for your TV D/E/F/G/H.
Attach the adaptor brackets to the back of the TV by lining up the VESA holes
and using bolts D/E/F/G/H, the washers Iand spacers Jand or K(if required)
to x the TV securely to the adaptor brackets.
With two people, lift and hold the TV in place while tightening the
bottom bolts Mwith a screwdriver to secure the adaptor brackets
to the wall plate.
Once attached, you can loosen the tilt adjustment knobs located
on the adaptor brackets to alter the viewing angle. When the
desired viewing angle has been set, tighten the adjustment knobs.
3. Attaching the Adaptor Brackets 4. Mounting the TV to the Wall Plate
Fig.7
Lift with
2 people
The wall bracket Ais attached to the wall using four appropriate screws/bolts
as shown in Fig.2. Make sure the screws/bolts are suitable for wood and large
enough to support the weight of the TV and bracket (if in doubt ask for advice at
your local DIY/hardware store and remember to make sure that the heads of the
screws/bolts are the correct size to hold the bracket securely in position).
Mark and drill four holes into the wood as close as possible to the centre of the
upright (you can use a stud detector to nd stud positions). To mark the holes, hold
the bracket Ato the wall, using a spirit level to make sure the bracket is level, and
mark the centre of each hole, see Fig.1. Drill the four holes and attach the bracket
Ato the wall using the appropriate screws/bolts.
A
Fig.1 Fig.2
Tip:
Make sure the holes you mark are
in the centre of the stud.
A
L
Use the spirit
level to ensure
bracket is level
Fig.3 Fig.4
L
Use the spirit level
to ensure bracket
is level
Fig.5
TV
TV
TV
0°
-10°
MM
BC
© Philex Electronic Ltd. 2018. V3.2
Technical Support:
www.philex.com/support
BC
I
D/E/F/G/H
I
H
K
I
H
K
J
I
H
KJ
I
J
F/G
I
J
F/G
I
J
K
F/G
Fig.6