Timeguard LED88 Manual

Installation & Operating Instructions
5W LED Energy Saver
Bulkhead
Model: LED88 – Black

1
1. General information:
Parts Included
sLuminaire unit.
sInstruction manual. Please keep safe
for future reference.
sAccessory pack.
as a fixed luminaire, and is not suitable for portable use.
Theunitcangetveryhotduringuse. Ensuretheunithascooledbeforehandling.
Ensure adequate ventilation space is allowed betweentheunitandanyobjectabove,infront
or to either side of the unit. Suggested space is 0.5m above, 0.3m to either side & 1.0m in front.
2. Selecting the location:
Tools & Parts Needed
sElectric or hand-held drill & bits.
sTerminal or electricians screwdriver.
sFlat and philips screwdriver.
sWire cutters.
Unit is for indoor and outdoor use. Unit must be mounted on a non-flammable surface

2
3. Installation:
After choosing a suitable location (see previous section) install the unit as follows:
Theunitissuitableforconnectiontoa230VAC50Hzelectricitysupply.Itissuggestedthat
2gauge is used. An isolating switch should be installed to switch
thepowertotheunitON&OFF.Thisisformaintenancepurposes.
IMPORTANT
Switch off the electricity at the fuse box by removing the relevant fuse or
switching off the circuit breaker before proceeding with the installation.
We recommend this unit be fitted by a qualified electrician. Install in accordance with wiring and
current building regulations. Please read the instructions carefully.
Pierce the grommet and pass the cable through the grommet.
Clampthecabletotherearoftheunitbeforesecuringtheunittothewall.
Fit grommet into its location hole ensuring a good seal.
Loosen up the bottom screw (Fig A). Remove wall plate by using a small flat screwdriver (Fig A) by
gently easing the wall plate outwards.
Fix the unit to the wall (Fig C). Close the rubber plug after tighten the screws (Fig E). Attach the unit
to the wall plate by a sound of click, tighten the bottom screw (Fig D). If using a power screwdriver,
use the lowest torque setting.
E
Close the rubber plug after
tighten the screws.
Open the rubber plug, mark position of the fixing holes (Fig B). Drill the holes. Insert the wall plugs
into the holes.

3
4. Operating and testing:
Turn the power to the unit ON and the unit will illuminate.
Connection
Connect the cable to the terminal block as follows (see connection diagram):
NEUTRAL (Blue) N
EARTH (Green/Yellow)
LIVE (Brown) L
Ensure the connections are secure. Refit wall plate ensuring it clicks firmly into place.
Mains
Supply
Isolation
Switch
N
L
LN
E
LN

4
If you experience problems refer to Troubleshooting Guide.
If problems still exist, do not immediately return the unit to store.
Telephone the Timeguard Customer Helpline
020 8450 0515
Qualified Customer Support Co-ordinators will be on-line to assist
in resolving your query.
5. Technical specifications:
Power Supply
Lamp Type
Environmental Protection
EC Directives
230 V AC ~ 50Hz
5W LED which is the equivalent light output of a 70W
Halogen Lamp
IP55 (suitable for outdoor use)
Conforms to current EC Directives
Class A+
6kWh/1000h
310lm typical
90x90 degrees
The lamps are not replaceable in this product
Energy Efficiency
Energy Usage
Output
Lamp Beam Angle

5
A
B
C
Open rubber
plug

6
D
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective
material or manufacture, within 3 years of the date of purchase,
please return it to your supplier in the first year with proof of purchase
and it will be replaced free of charge. For years 2 to 3 or any difficulty
in the first year telephone our helpline on 020 8450 0515.
Note: A Proof of Purchase is required in all cases. For all eligible
replacements (where agreed by Timeguard) the customer is responsible
for all Shipping/Postage charges outside of the UK. All Shipping costs are
to be Paid in advance before a replacement is sent.
Click

67.058.493 (issue 1)
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [e-mail]
For a product brochure please contact:
For assistance with the product please contact:
Zerofour – May 2013
or email [e-mail]
HELPLINE
020 8450 0515