Torin Black Jack BJ-450ST User manual

1800 833 800
Imported by
SJS Investment Pty Ltd
Bayswater WA6053
Working Load Limit：450kg
450KG ENGINE STAND
PART LIST

READ THESE INSTRUCTIONS CAREFULLY AND NOTE THE SAFETY INSTRUCTIONS AND WARNINGS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE TO PROPERTY AND/OR SERIOUS PERSONAL INJURY.
KEEP THIS INSTRUCTION MANUAL SAFE FOR FUTURE USE.
-Read and understand all warnings and instructions before use. Failure to follow instructions may result in
personal injury and/or property damage.
-Max. capacity is 450kg. Do not overload the device.
-Do not operate the device when you are tired, under the influence of alcohol, drugs or intoxicating medica-
tion.
-Keep children and unauthorized people away from the work area.
-Children or disabled people are not allowed to use the device.
-Use only on hard and level surfaces which are capable of sustaining the load.
-Inspect the device before each use.
-Make sure all components are correctly assembled and fasteners are fully tightened before applying load.
-Lock the mounting plate rotating mechanism before loading.
-Make sure the load is centered and secured to the mounting attachments.
-Use only high strength bolts for mounting the engine.
-Grasp the handle before unlocking the mounting plate.
-When moving a loaded stand, it must be as low as possible and another person must assist the transport.
Transport loads slowly.
-Never move a loaded stand across a floor having cracks, pebbles or other obstacles which might impede
movement.
-Never work under a raised load until it is secured by suitable means.
-Remove the lock pin slowly and carefully. Off-centered load may cause the engine and handle to rotate in
either direction when the lock pin is removed.
-Do not modify the device in any way.
-Failure to follow these warnings or instructions may result in personal injury and/or property damage.
WARNING:The warnings, cautions and instructions discussed in this instruction manual cannot cover all pos-
sible conditions and situations that may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into any product, but must be supplied by the operator.
Max. capacity 450 kg
Dimensions 930 x 780 x 895 mm
Weight 21 kg
1. Attach the main post (1) and front leg (14) to the side leg (2) with M12x80 bolt (3) and lock washer (10) up
from the bottom. The bolt will thread into the hex nut that is welded inside the front leg.
Before applying load, lock the mounting plate rotating mechanism. Using a hoist, suspend the engine at a level
with the mounting plate. With the mounting arms loose from the mounting plate (but not removed), bolt the
mounting arms to the rear of the engine using the bell housing mounting bolts (bolts not supplied). Make sure
the engine is centered and straight on the mounting plate, then tighten the mounting arms to the engine and to
the mounting plate. After making sure all connections are tight, SLOWLY lower the hoist, transferring the load
to the stand. To remove the engine from the stand, first attach the hoist to the engine using a sling or similar
device. After the hoist and sling are secured to the engine, raise the hoist, taking the load off the stand. The
mounting bolts can be removed freeing the stand from the engine.
A complete visual inspection must be made before each use of the stand. Check for broken or cracked welds,
excessive rust and loose, damaged or missing parts. Check that the wheels and castors operate smoothly.
Also check that the mounting plate rotation lock works properly before applying load. If any problems as de-
scribed above or otherwise are found, remove the stand from service. Also inspect the label, making sure that
it is legible and securely attached to the stand. If not, it must be replaced. If the stand has been or is believed
to have been subjected to an abnormal load or shock load, you must inspect the stand IMMEDIATELY before
putting the stand into or resuming service. If you are unsure about the condition of the stand, contact an au-
thorized service center or the importer.
Keep the stand clean and well lubricated. Lubricate all wheel axles with motor oil or light machine oil and
grease the castor swivel bearings once a year or as necessary. Also apply a thin coat of grease to the mount-
ing plate rotating mechanism as necessary, but at least once a year.
ytQ
ytQ
noitpircseD noitpircseD .oN .oN
1
1
tsopniaM
1
2
Side leg with fixed wheels
308x21M,tloB
3
1ylbmessadaeH
4
1nipkcoL
5
4smragnitnuoM
6
405x21M,tloB
7
621,rehsawtalF
8
621M,tunxeH
9
7
21,rehsawkcoL
01
2
”½3,leehwrotsaC
11
2
41,rehsawtalF
21
2
gnirreniateR
31
1
1
geltnorF
41
51
Side leg with castor wheels
1
lebaL
61
2
”4,leehwraeR
71
8
02x8M,tloB
81
8
8,rehsawkcoL
91
8
8M,tuN
02
PART LIST
IMPORTANT
SGNINRAW DNA SNOITCURTSNI YTEFAS
SPECIFICATIONS
ASSEMBLY
OPERATION
INSPECTION
MAINTENANCE