Torrot KIDS10 Series User manual

User Manual
Mainenance+Warranty
T10 E10 S10
T12 E12 S12
SIC58

Welcome to Torrot
Thank you for becoming the owner of one of
our funny electric motorbikes KIDS10 / KIDS12
for young riders!
In this manual you will nd information about how to
use and how to do the maintenance of your KIDS.
You will also nd information about the Torrot Electric’s
two years warranty that your new motorcycle has.

T12 E12 S12 KIDS
SCHOOL
USB
MAPPING
2 YEARS
TORROT
ELECTRIC
WARRANTY
MOTOR
BRUSHLESS
48V
POWER
KIDS10 FROM
350 TO 1050W
KIDS12 FROM
600 TO 1500W
LITHIUM
BATTERY
BRAKE DISCSYOUNG
ELECTRIC
3-9

5
KIDS
User Manual
Table of
contents
INTRODUCTION 06
THE KIDS 07
SPECIFICATIONS 08
COMPONENTS 14
CONTROLS 15
BEFORE USING IT 16
MAINTENANCE 18
BATTERY 19
BATTERY PRECAUTIONS 20
RECHARGE 21
ACCESS TO BATTERY KIDS10 22
ACCESS TO BATTERY KIDS12 23
BATTERY REMOVAL KIDS10 24
BATTERY REMOVAL KIDS12 25
ECU MAPPING 26
PC ECU MAPPING 27
BLUETOOTH APP 28
WIRING DIAGRAM I 30
WIRING DIAGRAM II 31
WARNINGS AND SECURITY 32
FAQ 33
TROUBLESHOOTING 34
WARRANTY 37

6
KIDS
User Manual
INTRODUCTION
The KIDS electric motorbike series for young riders allow a very
powerful learning curve in both off-road and on-road riding. There is
nothing similar to these miniaturized endurcross and supermotard!
The KIDS have been designed to give a realistic and authentic rst impression
in terms of handling, ergonomics and performance. Furthermore, very
high passive safety standards have been added to allow a 100% positive
experience.
Besides fast learning and a lot of fun, the KIDS bring to your son strong
pedagogical values: equilibrium, concentration and responsibility. Also we
can’t forget that these e-motorcycles are clean, quiet, and very reliable. The
future is here ;- )
To experience them with the maximum intensity and security, we recommend
you to read this handbook and make your children understand that this is not a
toy and make him/her comprehend the warnings and safety advises we give,
this way you will know when and how to charge the battery, how to do the
basic maintenance of the motorbike, check the brakes, etc. with simple and
practical advices.
From Torrot Electric, we insistently advise you to use always a helmet and the
proper protection equipment to have a satisfactory, funny and 100% secure
experience.
If you still have any doubt after consulting this manual, go
to your Torrot’s point of sale or write to [email protected]
*No contractual images. Due to our constant improvement policy, Torrot Electric Europa
reservesitsrightstointroducechangeswithoutnoticeinproductsortechnicalspecications.
The images of the product showed here can dier noticeably from the product delivered.

7
KIDS
User Manual
THE KIDS
The KIDS SERIES 10/12 are children’s electric motorbikes conceived
exclusively for boys and girls with maximum weight of 30kg for KIDS10
and 40kg for KIDS12. They are designed with care and passion by our
technicians to take the rst steps and initiate in the motorcycling world. The
KIDS are authentic miniaturized motorbikes, and with them, the youngest in
the household will learn, progress and have fun, turning into ‘little big’ riders.
The KIDS are not toys: please, parents or guardian must supervise the child
when using the motorbike!
With knobby tyres specic for trial practise, the T10/T12 offers to the young pilot
a perfect architecture to take its rst steps, with a very similar motorbike
that the one that is used by professionals. As a result of the most genuine
experience and developed by professional riders, lovers of this modality.
This trial motorbike can turn into a E10/E12 off-road motorbike with the special
kit. Take it into account!
The enduro electric motorbike of Torrot Electric has no rivals. Devilishly
beautiful, they will delight any child (and so do their parents), because of
the power offered thanks to their brushless motor and their lithium
batteries, they will offer (depending on the kind of use and other facts as the
ground or the rider’s weight) fun and ‘pro’ learning for 40 or more minutes (at
full speed). Their strong dynamics, their Italian EBS standard suspensions,
their almost indestructible fairing, their programmable power maps or their
off-road rims turn them into a unique motorbike.
Our supermotard has been designed to make an easier on-road learning
and progression in closed circuits (go-kart racing circuits, speed circuits...).
They have soft tyres for high speeds, with a good grip for a maximum speed
of 42 km/h offered by this model. They inherit the ergonomics of their E10/E12
siblings, for young riders and future child prodigies that desire to begin in the
motorcycling world.
QUALITY
T10/T12
S10/S12
E10/E12

8
KIDS
SPECIFICATIONS E10
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. EBR FORK (WHEEL TRAVEL 75mm)
REAR SUSP. SHOCK ABSORBER PRELOAD ADJUSTMENT (WHEEL TRA-
VEL 100mm)
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 350 W-1050 W / MAX. SPEED 40 KM/H
BATTERY 48V LiNiCoMn 6,6Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 10” x 1.60
TYRES MITAS C12 2.50-12 TT 37J
WEIGHT 22kg
MAX PILOT WEIGHT 30kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
TRAINING WHEELS
*Designed and made in barcelona
3-7
HANDLEBAR WIDTH 580mm
1200mm
850mm
545mm
790mm
220mm
User Manual
SPECIFICATIONS

9
KIDS
User Manual
SPECIFICATIONS E12
6-9
SPECIFICATIONS E12
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. HYDRAULIC FORK (WHEEL TRAVEL 100mm)
REAR SUSP. DNM GAS SHOCKABSORBER. PRELOAD ADJUSTMENT
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 600 W-1500 W / MAX. SPEED 52 KM/H
BATTERY 48V LiNiCoMn 8,8Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 12” x 1.60
TYRES MITAS C19 2.50-12 TT 37M
WEIGHT 30kg
MAX PILOT WEIGHT 40kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
*Designed and made in Barcelona
..
950mm
610mm
805mm
210mm
HANDLEBAR WIDE /ANCHO MANILLAR 580mm

10
KIDS
User Manual
SPECIFICATIONS
3-7
SPECIFICATIONS T10
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. EBR FORK (WHEEL TRAVEL 75mm)
REAR SUSP. SHOCK ABSORBER PRELOAD ADJUSTMENT (WHEEL TRA-
VEL 100mm)
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 350 W-1050 W / MAX. SPEED 30 KM/H
BATTERY 48V LiNiCoMn 6,6Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 10” x 1.60
TYRES MITAS C12 2.50-12 TT 37J
WEIGHT 22kg
MAX PILOT WEIGHT 30kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
TRAINING WHEELS
*Designed and made in barcelona
HANDLEBAR WIDTH 580mm
1200mm
850mm
440mm
790mm
220mm

11
KIDS
User Manual
SPECIFICATIONS t12
6-9
SPECIFICATIONS T12
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. HYDRAULIC FORK (WHEEL TRAVEL 100mm)
REAR SUSP. DNM GAS SHOCKABSORBER. PRELOAD ADJUSTMENT
(WHEEL TRAVEL 125mm)
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 600 W-1500 W / MAX. SPEED 40 KM/H
BATTERY 48V LiNiCoMn 8,8Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 12” x 1.60
TYRES TRIAL 2.50-12
WEIGHT 30kg
MAX PILOT WEIGHT 40kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
*Designed and made in Barcelona
..
950mm
535mm
805mm
210mm
HANDLEBAR WIDE /ANCHO MANILLAR 580mm

12
KIDS
User Manual
SPECIFICATIONS
3-7
SPECIFICATIONS S10
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. EBR FORK (WHEEL TRAVEL 75mm)
REAR SUSP. SHOCK ABSORBER PRELOAD ADJUSTMENT (WHEEL TRA-
VEL 100mm)
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 350 W-1050 W / MAX. SPEED 40 KM/H
BATTERY 48V LiNiCoMn 6,6Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 10” x 1.60
TYRES MITAS MC34 90/90-10 50P TL
WEIGHT 22kg
MAX PILOT WEIGHT 30kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
TRAINING WHEELS
*Designed and made in barcelona
HANDLEBAR WIDTH 580mm
1190mm
850mm
535mm
780mm
195mm

13
KIDS
User Manual
SPECIFICATIONS s12
6-9
SPECIFICATIONS S12
CHASSIS TUBULAR CrMo STEEL FRAME
FRONT SUSP. HYDRAULIC FORK (WHEEL TRAVEL 100mm)
REAR SUSP. DNM GAS SHOCKABSORBER. PRELOAD ADJUSTMENT
(WHEEL TRAVEL 125mm)
BRAKES HYDRAULIC BRAKE SYSTEM 160mm DISCS FRONT AND
REAR
MOTOR CONTROLLER 48V PROGRAMMABLE TOP SPEED, POWER, THROTTLE
SENSITIVITY AND REGENERATION
POWER 600 W-1500 W / MAX. SPEED 52 KM/H
BATTERY 48V LiNiCoMn 8,8Ah WITH BMS INTEGRATED (Battery Mana-
gement System) REMOVABLE
RIMS ALUMINUM 12” x 1.60
TYRES SUPERMOTARD 90/90 12
WEIGHT 30kg
MAX PILOT WEIGHT 40kg
CHARGER 54.6V 2A BATTERY CHARGER (4 HOURS)
OTHERS POWER TRAIN MANAGEMENT SOFTWARE INCLUDED.
(RS232-USB CABLE REQUIRED)
iNCLUDES POWER SWITCH 50-100%
DESIGNED AND MANUFACTURED IN EUROPE
OPTIONAL
BLUETOOTH MODULE VIA APP (iOS/Android)
REMOTE PARAMETER PROGRAMMING AND PARENTAL
CONTROL TORROT INVERTER FOR CAR CHARE (LIGHTER
SOCKET)
HANDLEBAR PROTECTOR
*Designed and made in Barcelona
..
950mm
610mm
805mm
210mm
HANDLEBAR WIDE /ANCHO MANILLAR 580mm

14
KIDS
User Manual
COMPONENTS
BRAKE DISC
TYRE
RIM
FORK
MUDGUARD
HANDLEBAR
BRAKE CALIPER
CHASSIS
MOOTREST
SHOCK ABSORBER
SWING ARM
SIDESTAND
SEAT
CHAIN
CHAIN TENSIONER
ON/OFF SWITCH
CHARGING PLUG
SERIAL NUMBER
a
b
c
d
e
f
g
h
i
j
k
l
b
m
e
d
g
a
b
c
d
e
f
g
h
i
k
l
m
n
o
j
n
o
f
q
q
r
s
t
v
POWER MODE SWITCH
r
s
t
u
u
v
CONTROLLER
MOTOR
BATTERY
IGNITION KEY
p
p

15
KIDS
User Manual
CONTROLS
To turn on the motorcycle turn the key in
ON position and press the red “ON/OFF” button
placed in the handlebar, next to the throttle grip.
When pushing it inwards the KIDS is ready to
ride. turn slightly the throttle grip to check if the
motor is working. To switch it off, press again the
same button.
Do not forget to fold the sidestand before riding
the motorbike.
The KIDS has a switch in the lower lefthand
art of the number plate. You can choose between
the full power option (100% of power)
or limit it to 50% of power.
* It is possible to map the control unit with a
RS232 connector / Bluetooth. To do it, check the
pages 26, 27 and 28, 29 of this manual.
REMEMBER TO SWITCH OFF
YOUR KIDS WHEN YOU ARE
NOT USING IT OR WHEN IS
GETTING CHARGED
a. On/O Switch
b. Throttle
c. Front Brake
e. Brake levers adjustment
d. Rear Brake
f. Power Mode Switch
af
100%
50%
TO AVOID INJURIES DURING THE USAGE, JUST PUT THE
KEY IN THE ON POSITION AND THEN TAKE IT OUT.

16
KIDS
User Manual
BEFORE USING IT
If you receive your KIDS in a box, verify that it contains the following
elements:
KIDS Motorbike with the handlebar disassembled.
4 allen M6 screws (preassembled in the handlebar clamp).
A box with charger and the power cord.
An information leaet.
HANDLEBAR ASSEMBLY
Unscrew the 4 preassembled M6 screws with a Nº 5 allen key. Extract
the plastic pipe and put the handlebar in its place. Check that the brake
lines have a natural position, in front of the KIDS.
Put the handlebar clamp on top of the handlebar and screw it slightly.
Adjust the handlebar position so it remains centered.
Rotate the handlebar so the brake levers are in a proper angle. To nish,
screw the four screws in a crossed sequence.
When we assemble each motorcycle in our factory Mataró, we test the
proper operation one by one. However, we want to ask you to check again
some components and t them to your necessities and tastes:
TYRE PRESSURE
A standard pressure of 1 bar (kg/cm2) is recommended for our models. The
correct pressure will increase the battery range and its drivability. Check
the attached table with recommendations for each model.
ALLEN Nº5
10/20º
1
2
3
x4
1
2
3
*RECOMMENDED PRESSURE FOR DRY, WET AND WITH MUD ENVIROMENTS.
AND FOR A 20KG RIDER. TO ADJUST THE CORRECT PRESSURE IN THE TRIAL
MOTORBIKE, YOU WILL NEED A SPECIAL MANOMETER.
RECOMMENDED PRESSURES TABLE* BAR (Kg/cm2)
MODEL FRONT REAR
0,9 0,6-0,8
1,0 1,2
1,2 1,4
T12T10
S12
S10
E10 E12
YOU MUST DO A FULL BATTERY CHARGE
BEFORE THE FIRST USE

17
KIDS
1
User Manual
BEFORE USING IT
BRAKES
The KIDS are equipped with a cable-actuated disc brakes system. Check that
both front and rear brakes work properly using the left and right brake levers
while moving the motorcycle slightly.
If the brake lever is far from your child’s ngers, you can bring them closer to the
grip using the screw with an allen key.
BRAKES MAINTENANCE
In order to preserve the effectiveness of the braking system of your KIDS, it is
important to do an inspection after every use:
- If there are less than 2mm of useful material in the brake pads, they should be
replaced
- If the brake levers have too much range, a bleeding of the braking system need
to be carried out.
WARNING: This operations is difcult so if you don’t have the knowledge required
you better go to your nearest Dealer.
HOW TO ADJUST THE PRELOAD OF THE SHOCK ABSORBER
You can adjust the preload of the shock absorber to adapt the rear suspension to
the weight and preferences of your child. Using a hook wrench for dampers,
turn the nut which supports the spring. The more you compress the spring,
the more preload you will get.
There are springs available in our shop:
KIDS10: 01RT-00100-ZZ (550lb/in) o 01RT-00021-ZZ (750lb/in)
KIDS12: 02RT-00030-ZZ (450lb/in) o 02RT-00040-ZZ (650lb/in)
1
3
2
2
3
DURING THE USE, THE BRAKES CAN REACH HIGH
TEMPERATURES. DO NOT TOUCH THE BRAKES IN ANY
CASE DURING OR JUST AFTER THE USE.
ESPECIFICACIONES S12
CHASIS TUBULAR DE ACERO CrMob
SUSP. DELANTERA HORQUILLA HIDRÁULICA EBR (RECORRIDO RUEDA
100mm)
SUSP. TRASERA AMORTIGUADOR HIDRAULICO DNM. AJUSTE EN PRE-
CARGA (RECORRIDO RUEDA 125mm)
FRENOS SISTEMA FRENOS HIDRAULICO. DISCOS (160mm) DEL./
TRAS.
CONTROLADORA
MOTOR
48V PROGRAMABLE VELOCIDAD MAX, POTENCIA, TAC-
TO ACELERADOR Y REGENERACIÓN
POTÉNCIA 600W-1500W / VELOCIDAD MÁX.52 KM/H
BATERÍA 48V LiNiCoMn 6,6Ah CON BMS (Battery Management Sys-
tem) INTEGRADO, EXTRAIBLE.
LLANTAS ALUMINIO 1.85x12”
NEUMÁTICOS SUPERMOTAR 90/90-12
PESO 30kg
PESO MAX. PILOTO 40kg
CARGADOR 54.6V 2A CARGADOR DE BATERÍA (4 HORAS)
VARIOS SOFTWARE CONFIGURACIÓN INCLUIDO (REQUIERE
CABLE RS232-USB)
iNCLUYE SWITCH DE POTENCIA 50-100%
DISEÑADA Y FABRICADA EN EUROPA
OPCIONAL
MODULO BLUETOOTH VIA APP (iOS/Android)
PROGRAMACIÓN REMOTA Y CONTROL PARENTAL
INVERSOR TORROT PARA CARGA EN COCHE (TOMA
ENCENDEDOR)
PROTECTOR GOMA MANILLAR
*Diseñada y ensamblada en Barcelona

18
KIDS
User Manual
MAINTENANCE
CHAIN TENSION EXAM
The lifespan of the chain depends on its correct lubrication and adjustment. A bad
maintenance can cause a premature wear or damages to the chain and to the
rear/front sprockets.
Before doing the maintenance to the chain, turn OFF the ON/OFF switch. For a
better measurement, the pilot should be sitting in the saddle in the driving position
because when there is no weight applied, the chain is more stretched.
Check the movement up and down in the centre of the lower part of the chain as
is showed in the image . The tension must allow a vertical movement from 10
to 20mm.
Turn the wheel slightly and check the chain movement in different points,
measuring always the gap in the same place.
Examine the teeth in the front and rear sprocket to see if they are wore away or
damaged.
ADJUST YOUR MOTORCYCLE CHAIN TENSION
If the vertical movement of the chain is not inside the recommended values,
adjust the tension as indicated below:
- With a 19 mm wrench unbolt the rear axle .
- Turn the eccentrics of both sides by pushing the wheel backwards to stretch
the chain and push it frontwards to do the opposite.
- Screw the axle again ensuring that the chain and the front and rear sprockets
are aligned. Check the movement of the chain again.
10-20 mm
1
2
3
1
23

19
KIDS
User Manual
BATTERY
The KIDS10 is provided with a LiNiCoMn 48V and 6.6Ah (316.8Wh of
capacity) battery which supplies the motor. The KIDS12 has a battery of
48V and 8,8Ah (422,4Wh).
This kind of battery does not have the ‘memory effect’ and can be recharged
even if they are not fully discharged.
- The complete capacity of the battery will be achieved after several charge
and discharge cycles. Then you will get more battery range after the rst
uses.
- The KIDS is delivered with the battery at half capacity.
- Always try to charge the battery completely.
- For the correct maintenance of the KIDS, it is recommended to do a full
discharge and charge cycle at least once per month even if the motorbike
is not used.
- If you prevent that you KIDS is will not be used in 1 month or more and
is not possible to charge the battery at least once in a month, you shoud
leave the charger connected to the battery, it will provide maintenance to
the battery and won’t consume extra energy.
-The charger is a component that can heat up noticeably during its use.
Therefore they must be always used in places with good air circulation.-
Never cover it up and let it get wet.
- Use only the charger provided by Torrot Electric to charge the battery.
- The charge of the battery must be done in temperature conditions between
5 and 40ºC. Below 5ºC, the charge cycle will be increased and above 40ºC,
the battery can be damaged..
IT IS VERY IMPORTANT TO CHARGE THE BATTERY COMPLETELY
BEFORE THE FIRST TIME USE.
DO NOT LEAVE THE BATTERY DORMANT FOR LONG PERIODS OF TIME,
THEY CAN BE DAMAGED
ENSURE THAT YOU DO NOT LEAVE THE MOTORBIKE TURNED ON,
THIS WILL DISCHARGE THE BATTERY

20
KIDS
User Manual
1. GENERAL
a. The battery is composed of lithium-ion cells with high density energy.
In any case it should be manipulated. The disobedience to this indication
involves electric and chemical risk and can result in serious damage or
injury.
b. Inspection, reparation or replacement of the battery or any of its ele-
ments by non-authorized manufacturers is prohibited.
c. Manipulation or reparation of any electric element external from the
battery by non-authorized manufacturers is prohibited.
2. BATTERY DAMAGE
All abusive treatment to the vehicle can affect the battery’s lifespan. To keep
it in good condition and extend its lifespan, follow these instructions:
a. Avoid using the vehicle in conditions of extreme heat or cold beyond
the limits set by the manufacturer.
b. Avoid charging the battery in extreme conditions of heat or cold beyond
the limits set by the manufacturer.
c. During dormant periods, the vehicle must be stored in a dry place,
away from sources of cold and / or heat and direct sunlight.
d. Avoid unnecessary hits and vibrations to the vehicle. Periodically check
the insulation placed between the chassis and the battery of the vehicle is
in good condition. Otherwise, replace it.
e. The self-discharge is a natural characteristic of the battery and must be
controlled. For long periods of inactivity, you should periodically connect
the charger and perform full battery charges.
f. Avoid partial charges from the battery. For proper daily use, the battery
should always be fully charged.
g. As a general rule, it is advisable to keep the battery connected to the
charger for a certain time after the completion of a charge.
h. Never use any charger that has not been directly supplied by the ma-
nufacturer or an authorized dealer.
i. Avoid forcing the vehicle abnormally during use.
j. Your battery has internal protection against electrical hazards that can
act automatically. In case of a faulty operation or no operation of the bat-
tery, contact the manufacturer for repair.
k. Keep your battery clean and in good condition, carefully remove dust,
dirt and other external elements that can be introduced into the battery
compartment during use.
l. If you detect deterioration in the electrical system, disconnect the vehi-
cle and contact an authorized Torrot dealer for repair service.
m. Avoid direct contact of the electrical system of your vehicle with water,
mud or similar environments. If water is accidentally introduced into any
electrical element of the vehicle, unplug it and wait for it to dry naturally
before using it again.
BATTERY PRECAUTIONS