Toshiba SD-R1002 User manual

CD-RW/DVD-ROM
DRIVE
SD-R1002
Installation Instructions
with Adaptec
®
Easy CD Creator
TM
and
CyberLink PowerDVD
TM
Software
VERSION 3.0
DECEMBER 2000
TOSHIBA
StorageDeviceDivsion

WARNINGS
Thisequipment(anopticaldiscdrive)handledundertheconditionsoutofequipmentspecificationsmaycause
heavyload,heatgeneration,malfunction,erroneousoperationandperformancedegradation.Therefore,please
handlethisequipment properly in compliancewiththewarningsprovidedbelow. Intheeventthat you do not
complywiththe warnings, Toshiba cannot guarantee thesafety,reliability and performance oftheequipment
expressly provided in the specification. Manufacturers and resellers of the computer system using this
equipmentand/or this equipmentitselfshallnotify the end-usersofthewarnings provided hereinandensure
them to comply with these warnings in an appropriate manner.
1. This equipment does not involve any over-current protection circuit. Use an appropriate over-current
protectionin the computersystemwhichthis equipment would beconnected. Toshiba shallnotbeliable
forany damages tothesystem which doesnothave any over-currentprotection.
2. DONOT disassembleormodifythis equipment. Toshibashall not make anyguaranteetothe reliability,
safetyandperformance of this equipmentexpresslyprovidedinthespecificationand nor be liable forany
damagesresulting from such unauthorizeddisassemblyormodification.
3. Read carefully and comply with this manual in order to avoid the risk of data error in writing operation.
Suchpossibledataerror would be made byanyfactorsotherthanthisequipment(i.e.,poorstorage media,
misuse of this equipment, malfunction in a computer system connecting this equipment, etc.). Toshiba
shall not be liable for any damages resulting from such data loss. Check whether the original data is
correctlycopiedor storedupon completion ofwritingoperation.Takeany necessary measuresto protect
yourdatasuchassystembackup and/or mirroring disk subsystems in ordertoavoidtheriskofunexpected
data loss or data corruption resulting from failure in this equipment for some reason.
Manufacturersandresellers of the computer systemusingthisequipmentshallberequired to consider the
safetyof such computer systemanddataintegrityin order to avoidtheriskofany consequential damages
causedbydatalossordatacorruptionandanyproblemsoraccidentcausedbymalfunctionofthecomputer
system.
DONOTuse thisequipmentin the systemsuchas medical equipment whichmaycause personal injury
orpropertydamagesresulting from malfunction of thisequipmentandunexpecteddatacorruptionordata
errorin reading operation.
4. Turn off the power for this equipment and wait more than one (1) minute before you eject the disc using
theemergency eject mechanismwhenadisc cannot be ejectedforsomereasons in ordertoavoidthe risk
of damages to the disc.
1. Turnoff the system power before mounting/removing this equipment in order toavoidtheriskofdamages
to this equipment.
2. Insert the DC power plug in correct direction in order to avoid the risk of damages to this equipment.
3. Handle thisequipment only inelectrostatically safeenvironment and donottouchconnecting terminals
with empty hands when you build in or pull out this equipment from other product in order to avoid the
riskof malfunction ofthisequipment.
4. DONOT do any of the following:
●DONOTuse storage media (CD’s / DVD’s) that are notthecorrectsizeorshape,or donotmeet the
minimumformatting requirements.
●DONOTinsert more than one (1)CDorDVDdiscintothedriveat any time. Doing so willdamage
or destroy this equipment and could damage or destroy the disc or cause data loss or corruption.
●DO NOT load or eject any CD or DVD disc with force. Doing so will damage or destroy this
equipment and could damage or destroy the disc or cause data loss or destruction.
●DONOTeject a CD or DVD disc while the drive is in operation. Doing so will damage or destroy
this equipment and could damage or destroy the disc or cause data loss or corruption.
●DO NOT insert anything else into the drive other than a CD or DVD disc. Doing so will damage
or destroy this equipment.
5. Beforeyoucarryormovethisequipment,alwaysturnonthisequipmentandpushaejectbuttontoclose the
disc tray in order to avoid the risk of damages to this equipment. You can not fix the internal unit of this
equipmentcompletely if you closethedisctray while power isnoton.
NOTICE

Congratulations on your purchase of aToshiba CD-RW/DVD-ROM drive and Kit.
The following information will help you in the simple installation of your new
CD-RW/DVD-ROM drive.
CHECKING YOUR KIT PACKAGING
Please unpack your CD-RW/DVD-ROM kit, and assure that you have the follow-
ing items:
lToshiba CD-RW/DVD-ROMDrive
lCD-R Blank Media CD
lCD-RW Blank Media CD
lCyberLink PowerDVD™Software
lAdaptec®Easy CD Creator™CD Recording Software Package
lBIGWIGDVDKEEPER SERIESTWO disc
lCD-RW/DVD-ROM Installation Instructions (this manual)
lQuick Start Guide
lMounting screws (4)
lIDE BUS cable
lDVD/CD sound cable
Additional items you may need that are not included in the kit are:
lPhillips Screwdriver
lMounting hardware (i.e. some computer systems use mounting rails).
SYSTEM REQUIREMENTS
The CD-RW/DVD-ROM kit requires the following:
✔At least 55MB of free hard disk space
✔At least 32MB of RAM
✔*Pentium II processor at 266MHz or higher or....
*Celeron 300A processor or higher or....
*K6-2 processor at 300MHz or higher
✔Display card supporting DirectDraw
✔16-bit or better sound card
✔Microsoft™Windows 95 or higher
✔Amplified stereo speakers
* Theserequirementsare only requiredif you are usingthe CyberLink PowerDVD™
software. The SD-R1002 CD-RW/DVD-ROM will work as a CD-ROM and CD-
RW when using a lower speed Pentium system.
1

2
The following steps must be performed to properly install your CD-RW/DVD-
ROM.
●Set drive’s jumpers
●Connect audio cable
●Attach IDE BUS cable
●Connect power cable
●MountCD-RW/DVD-ROM
●Install CyberLink PowerDVD™software (used for viewing DVD movies)
●InstallAdaptec®Easy CD Creator™software (used for recording CDs)
SETTING JUMPERS
The mode select jumpers are six (6) straight angle pins located on the rear of the
CD-RW/DVD-ROM. By placing a jumper on the pins, you can select the following
functions: CS: – Drive is configured using host interface signal CSEL
SL: – Configures drive as Slave
MA: – Configures drive as Master (default mode)
ModeSelectJumpers
In most installations, jumper should remain in MA (Master) position (factory
default). It is recommended that you install your CD-RW/DVD-ROM only on the
secondary IDE BUS. If you are installing on primary IDE BUS, your hard drive
would then be the Master, and you should set your CD-RW/DVD-ROM to the
Slave position (SL).
PLACING CD-RW/DVD-ROM INSIDE YOUR COMPUTER
Now that you have set your drive’s jumpers, you are ready to install your
CD-RW/DVD-ROM inside your computer.
☞☞
☞☞
☞IMPORTANT: Disconnect power from your computer system before
C
SS
LM A
beginninginstallation.

1. Remove computer cover and faceplate if required (refer to your computer
system’s manual for removal information).
2. If the CD-RW/DVD-ROM is replacing a CD-ROM, disconnect all connectors
and remove the CD-ROM presently installed in your system.
3. Your Toshiba CD-RW/DVD-ROM can be placed in any free half-height drive
slot at the front of your computer. (It can be mounted horizontally or vertically.)
4. Carefully start sliding the CD-RW/DVD-ROM into the opening with the disc
tray facing the front of the computer. Before you push the drive all the way in
you will need to connect the IDE BUS cable, audio cable and the power cable
to the back of the drive.
CONNECTING CABLES
Cable Locations on Rear of CD-RW/DVD-ROM
IDE BUS (Data) Cable - Most computer system have a primary and secondary
IDE BUS cable already installed (an IDE BUS cable is include with your kit if your
system does not have a secondary IDE BUS cable).
IfyouarereplacingaCD-ROM:connect the CD-RW/DVD-ROM drive using the
BUS cable that the CD-ROM was connected to. Insure that the jumper setting of
the CD-RW/DVD-ROM is the same as the CD-ROM drive you are replacing.
If the CD-RW/DVD-ROM is not replacing a CD-ROM and/or is in addition to a
CD-ROM: locate the secondary IDE BUS cable in your system. If your system
does not have a secondary IDE BUS cable installed, you will need to install the
IDE BUS cable that was included with your kit.
Installing secondary IDE BUS cable: locate the secondary IDE BUS connec-
tor on your system’s motherboard (refer to your system’s documentation for
location). Connect one end of the IDE BUS cable to motherboard, assuring
that it is keyed properly and that cable’s colored edge is aligned with Pin 1.
3

4
Connect secondary IDE BUS cable to CD-RW/DVD-ROM drive, assuring that pin
1 of the cable (side with red stripe) is connected to pin 1 on the drive.
• If the CD-RW/DVD-ROM is the only drive connected on the secondary IDE
BUS cable: connect drive to the last set of pins on IDE BUS cable.
• If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS
cable: connect CD-RW/DVD-ROM to the open middle connector .The CD-
RW/DVD-ROM drive should then be jumpered to SL (slave) position.
Ifthe CD-RW/DVD-ROMisto be the slaveon the PrimaryBUS: connect the CD-
RW/DVD-ROM to the open connector on the primary IDEBUS cable.TheCD-RW/
DVD-ROM drive should be jumpered to the SL (slave) position. Note: the primary
IDE BUS cable, in most cases, will be connected to your hard drive. The hard
drive will be the Master on the primary BUS.
Power Cable - Inside your computer system, locate an unused power supply cable.
Connect the power cable to the power socket at the back of the CD-RW/DVD-
ROM. One side of the plug has chamfered edges, so the power connector fits only
one way. Push plug completely into the socket making sure the plug fits correctly.
Audio Cable - Connecting your CD-RW/DVD-ROM to your sound card allows
you to play audio CDs on your computer (speakers or headphones are also needed).
Ifthe CD-RW/DVD-ROM isin additionto a CD-ROM:If you choose to have both
a CD-ROM and CD-RW/DVD-ROM installed in your system, in most circum-
stances, only one audio cable can be used (there are some sound cards that will
allow you to have two audio connections). You must decide which device you
would like to hear audio from and connect the audio cable from the sound card to
the CD-ROM or CD-RW/DVD-ROM (DVD audio is transmitted through the data
cable, not the audio cable).
If the CD-RW/DVD-ROM is to be the only CD-ROM device in your system:
• If replacing a CD-ROM that had an audio cable connection: connect CD-
RW/DVD-ROM drive to the audio cable that the CD-ROM was connected.
Cable connects to the analog audio connector at the left rear of the CD-RW/
DVD-ROM (see Cable Location photo on page 3 for location).
• If you do not have an audio cable presently in your system: connect the CD-
RW/DVD-ROM using the audio cable that was included with this kit. Con-
nect one end to your sound card and the other end to the analog audio con-
nector at the left rear of the CD-RW/DVD-ROM (see Cable Location photo on
page 3 for location). Refer to the instructions which came with your sound
card for details on any sound-driver software required.

COMPLETING INSTALLATION
After you have connected all the necessary cables, push the CD-RW/DVD-ROM
completely into the computer’s drive slot. Mount the drive per your computer’s
instructions using the screws included in your kit. If you are using other screws,
assure that the screw length does not exceed 3±0.5mm (measured from outside
surface of side or bottom of CD-RW/DVD-ROM to tip of screw). Replace the
computer cover and all outer screws.
ATAPI CD/DVD Software Driver:
Toshiba’s CD-RW/DVD-ROM drives do not require any unique device drivers for
Windows '95/'98/2000/NT. After installing your drive and re-booting, your sys-
tem should recognize your drive. Win '95/'98/2000/NT operating systems support
allToshibaATAPI CD-RW, CD-ROM and DVD-ROM drives natively.
Adaptec®Easy CD Creator™Software:
Adaptec®Easy CD Creator™software is used to record CDs with your new CD-
RW/DVD-ROM. To install software insert the installation CD into your newly
installedCD-RW/DVD-ROM.If“Autorun” isenabled onyour system, theAdaptec®
Installation window will appear automatically. If it does not appear, go to Win-
dows Start menu, select “Run”and type d:\setup.exe (substitute the appropri-
ate letter of your CD-RW/DVD drive ford:). From theAdaptec®Installation win-
dow select Adaptec®Easy CD Creator™and follow the installation instructions
that appear on your screen. For additional information on this software, please
refer to the documentation found on the Adaptec®Easy CD Creator™CD.
CyberLink PowerDVD™:
CyberLink PowerDVD™is a high-quality, pure-software DVD player that brings
high-quality movies and karaoke into your multimedia PC. You can playback
high resolution DVD titles or MPEG-2 files with superb MPEG-2 video and Dolby
AC-3 audio quality.
To install, insert CyberLink PowerDVD™into your newly installed CD-RW/DVD-
ROM. Go toWindows Start menu, select “Run”and type d:\setup.exe(substi-
tute the appropriate letter of your CD-RW/DVD-ROM drive for d:). Follow the
installation instructions on screen. For additional information on using this soft-
ware, please refer to the PowerDVD™Help file (if you have opened PowerDVD™
software, click “?”).
5

CD-RW/DVD-ROM FRONT PANEL
The photo illustrates the following features of the SD-R1002 CD-RW/ DVD-ROM
front panel:
Q Headphone Jack T Busy Light
R Volume Control U Eject Button
S Loading Tray V Emergency Eject Hole
CD-RW/DVD-ROM BACK PANEL
The photo below illustrates the following features of the SD-R1002 and CD-RW/
DVD-ROMs back panel:
Q Digital Audio Out Connector T ATAPI Connector
R Analog Audio Out Connector U Power Connector
S Mode Select Jumper
6

TECHNICAL SUPPORT
Technical support can be obtained by calling 949/455-0407 or by sending an
email to: [email protected] or visiting our website at:
http://www.sdd.toshiba.com
FCCDECLARATIONOF CONFORMITY
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV
reception. The user is cautioned that changes and modifications made to the equipment without the approval of
the manufacturer could void the user's authority to operate this equipment.
LASER CAUTION
This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT". To use this model
properly, read this Owner's Manual carefully and keep this manual for future reference. In case of any trouble with
this model, please contact your nearest "Authorized Repair Center". To prevent direct exposure to the laser beam,
do not try to open the enclosure
SPECIFICATIONS SD-R1002
DVD CD
DATACAPACITY mode 1 mode 2
(bytes/block) 2,048 2,048 2,336
ROTATIONALSPEED DVD:2,800rpm CD: 5,100rpm
(2 -4.8X CAV) (10.3 - 24 CAV)
DVD-R: 1,100 - 2,800rpm CD-RW: 3,400rpm
(2X CLV) (6.9 - 16X CAV)
CD-R,CD-RW(Write):
850 - 1,980rpm (4X CLV)
SUSTAINEDDATA mode 1 mode 2
TRANSFERRATE(kbytes/sec) 2,704 - 6,536 1,552 - 3,600 1,770 - 4,106
ACCESSTIME(Typ.)
Avg. RandomAccess 160ms 110ms
Avg Random Seek 140ms 105ms
Avg. Full Stroke 230ms 180ms
DATABUFFER 2Mbytes
POWERSUPPLY +5v, +12v
MTBF 100,000 hours
DIMENSIONS(WxHxD) 5.7” x 1.6” x 7.6” (146mm x 41.5mm x 193mm)
WEIGHT 0.58lbs ( 0.98kg)
MOUNTINGORIENTATION ±10° vertical / ±20° horizontal
7

WARRANTY INFORMATION
Toshiba America Electronic Components, Inc. (“TAEC”) warrants that all prod-
ucts will, upon delivery by TAEC to the customer in new condition, be free from
defects in material and workmanship for a period of twelve (12) months after
delivery. TAEC warrants that spare Parts and Accessories will be free from defects
in material and workmanship for a period of ninety (90) days. These warranties
are effective from the date of shipment by TAEC to the original purchaser and
will be extended only to that original purchaser. TAEC will, at its option, repair
or replace the defective item under warranty in accordance with TAEC’s pub-
lished Repair Policy and Procedure.
This warranty is void: (a) if the Products are used under other than normal use
and maintenance conditions, (b) if the Products are modified or altered, unless
the modification or alteration is expressly authorized by TAEC, (c) if the equip-
ment is subject to abuse, neglect, lightning, electrical fault, or accident, (d) if the
Products are repaired by someone other than TAEC, (e) if the serial numbers of
the Products are defaced or missing, or (f) if the Products are installed or used in
combination or in assembly with products not supplied by and which are not
compatible or of inferior quality, design or performance.
This Warranty shall constitute the sole and exclusive liability of the TAEC, it's
successors or assigns, in connection with the goods purchased and is in lieu of all
other Warranties, expressed or implied, including but not limited to any implied
warranty of merchantability, fitness for a particular purpose or fitness for use, and
all other obligations or liabilities of TAEC, it's successors or assigns.
Under no circumstances will the customer or any user or other person be entitled
to any direct, indirect, special, consequential, or exemplary damages, for Breach
of Contract, Tort, or otherwise. Under no circumstances will any such person be
entitled to any sum greater than the purchase price paid for the product that is
malfunctioning.
This warranty does not apply to expendable parts such as fuses, filters, remov-
able media, and other such parts classified by Seller as expendable.
• All repairs will be performed at TAEC’s Repair facility, except for repairs made at the
Purchaser’s site, as specifically agreed byTAEC in writing.
• Purchaser shall bear the cost of shipping to TAEC’s facility those items that fail while
under warranty. TAEC shall bear the cost of return shipment to Purchaser’s facility.
• Repairsonproductsthat failduringthenew productwarrantyperiodare warranted forthe
remainder of the new product warranty period or 90 days, whichever is the greatest.
• The repair of product that failed after the expiration of the original warranty period is
warrantedforninetydaysfromthe date the repaired itemisshippedback to the customer.
• To obtain service under this warranty, the Purchaser must bring the malfunction of the
Product to the attention ofTAEC within the twelve (12) month period and no later than
thirty (30) days after such malfunction, whichever occurs first. Failure to bring the mal-
function to the attention of TAEC, within the prescribed time, will result inthe Purchaser
beingnotentitledtowarrantyservice.
8

460018-c0
P/N 460018-C0