Toshiba 44NHM54 User manual

FILE NO. 050-200423
SERVICE MANUAL
44NHM84

- 2 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the specified.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
CANADA: LG Electronics Canada, Inc. 550 Matheson
Boulevard East Mississauga, Ontario L4Z 4G3
USA : LG Customer Interactive Center
P.O.Box 240007, 201 James Record Road Huntsville,
AL 35824
Digital TV Hotline [phone]
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF

- 57 -
TABLE OF CONTENTS
SPECIFICATIONS ...................................................................................................... 4
DESCRIPTION OF CONTROLS ................................................................................ 5
ADJUSTMENT INSTRUCTION ................................................................................ 12
PRINTED CIRCUIT BOARDS .................................................................................. 18
BLOCK DIAGRAM ................................................................................................... 29
EXPOLODED VIEW ................................................................................................ 30
EXPOLODED VIEW PARTS LIST ......................................................................... 31
SCHEMATIC DIAGRAM .......................................................................................... 32
ELECTRICAL REPLACEMENT PARTS LIST.......................................................... 48
- 3 -

- 4 -
Product Specifications
Model
44NHM84 Horizontal Size (Inches) 39.92
Height (Inches) 29.19
Depth (Inches) 14.29
Weight (lbs.) 59.5
Power Requirement AC 120V, 60Hz
Television System NTSC, External STB is required for the reception of Satellite broadcasting or Digital Cable
broadcasting
Television Channels VHF: 2 - 13
UHF: 14 - 69
CATV: 1 - 125
Power Consumption (W) 230W
Antenna 75 ohm External Terminal for VHF/UHF
Audio Output (W) 12W x 2
External Input/Output Ports A/V input (3 set)
Monitor out (1 set)
S-Video input (2)
COLORSTREAM HD input (2 set)
RGB input (1)
DVI input (1)
RGB/DVI audio input (1 set)
Variable audio output (1 set)
Audio center mode input (1)
Upgrade port (1)
RF input (1)
• This model complies with the specifications listed below.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be
added in the future.
SPECIFICATIONS

- 5 -
Function Status Indicators
Lamp indicator, operation indicator, and temperature indicator located below the front panel
controls, reveal the operating status of the DLP projection TV.
Operation Indicator
Lamp Indicator
Temperature Indicator
Off Power cord is not connected.
Red Power Cord is connected, TV is in standby mode.
Green TV turns on.
Orange (flashing) Preparing operation in standby mode.
Green (flashing) The lamp cover is not closed.
Orange The projection TV is overheating. Check the blocked vents of
the projection TV .
Red The projection TV shut down due to overheating.
Red (flashing) The projection TV shut down due to the cooling fan trouble.
Contact an authorized service center.
Operation Indicator
Lamp Indicator
Temperature Indicator
DESCRIPTION OF CONTROLS

- 6 -
AUDIO
CENTER
MODE IN
DVI INPUT
COLORSTREAM HD
INPUT2 INPUT1
PR
PB
Y
PC/DTV
(XGA/
480p/
720p/
1080i)
PC/DTV
(XGA/
480p/
720p/
1080i)
RGB INPUT
UPGRADE PORT RGB/DVI INPUT
(R)
(L)
AUDIO
(R)
(L)
AUDIO
(R)
(L)
AUDIO
VARIABLE
AUDIO OUT
MONITOR
OUT VIDEO INPUT 2 VIDEO INPUT 1
S-VIDEO
(R)
(L)
AUDIO
VIDEO
MONO
+75 Ω
ANT IN
DTV /DVD
(480i/
480p/
720p/
1080i)
(480i/
480p/
720p/
1080i)
Mini glossary
JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are
color-coded.
SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.
Rear Connections Panel
S-VIDEO In
A connection available with
some high-end equipment
that provides even better pic-
ture quality for Video 2.
Variable Audio Out
Used to connect either
an external amplifier, or
add a sub-woofer to your
surround sound system.
RF Connector: Antenna
Used to connect analog
cable or antenna signals
to the television, either
directly or through your
cable box.
Video 1 or 2
Connects the video sig-
nals from various types
of equipment.
COLORSTREAM HD
Connect a ColorStream HD video/audio
device to these jacks. Refer to your DVD
manual for further information.
Connecting cables and external equipment to your TV.
Monitor Out
Connects to a second TV
or Monitor.
Left/Right Audio
Used for stereo sound
from various types of
equipment.
RGB/DVI Input
Connect the TV output con-
nector from a PC/DTV to
the appropriate input port.
RGB/DVI Input
Used for audio connec-
tions from a PC source or
HD-STB Satellite system.
Audio Center Mode In
Connect to external Dolby¨
Digital Center “preamp out-
put.”
DESCRIPTION OF CONTROLS

- 7 -
Front Connection Panel
Front A/V Panel
S-VIDEO
VIDEO
FRONT A/V
AUDIO
(R)
(L)/
MONO
There are four jacks on the left front of your projection TV
that make connecting Audio/Video devices like video games
and camcorders very simple.
The jacks are like those found on the back jack connection
panel. This means that most equipment that connects to
those types of jacks on the rear jackpack, may be connect-
ed to the front connection panel.
To use the front jacks as the signal source, select them
using Main Input menu as described on page 27. They will
be named “Front Video” in the Main Input menu.
Left/Right Audio
Used for stereo
sound from various
types of equipment.
Video
Connects the video
signals from any piece
of equipment. S-Video
A connection available on
some very high-end equip-
ment that provides better
picture quality than video
input.
If you input both Front Video and S-
Video, only the S-Video will work.
If you’re connecting a video game
device, make sure to change the
picture settings with the Picture Mode
option in the Video menu.
Mini glossary
A/V CABLESAudio/Video cables. Three cable connectors—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used
for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.
A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).
W
W
DESCRIPTION OF CONTROLS

- 8 -
Remote Control Functions in TV Mode
1 2 3
4 5 6
7 8 9
0
TV
MODE LIGHT POWER
TV/VIDEO DVI
RGB
VCR CABLE DVD SAT
MUTE
SWAPPIPCH- PIPCH+
PIP
PIC SIZE
REC STOP
PAUSE
REW
PLAY
FF
MENU EXIT
CC FREEZE
PIP INPUT
VOL CH
SURF
SAP VIDEO
C/S HD2C/S HD1
FRONT
SKIP
ENTER
CH RTN
SURF
Scrolls the Surf channel list.
MENU
Brings up the main
menu to the screen.
EXIT
Clears all on-screen dis-
plays and returns to TV
viewing from any menu.
FREEZE
Captures and freezes the currently-
viewed main picture.
VIDEO
Adjusts the factory preset
picture according to the
room.
PIPCH+
Changes to next higher PIP
channel.
SWAP
Switches the picture from
PIP, POP, or twin picture to
the main screen.
MUTE
Switches the sound on or off
THUMBSTICK
Allows you to navigate the on-screen
menus and to adjust the system set-
tings and preferences, by moving to an
option with
F G and selecting the high-
lighted option with .
TV/VIDEO
Selects: Analog, Video1,
Video2, Front video,
ColorStream HD1-2, RGB, and
DVI input sources.
MODE
Selects the remote operating
mode: TV, VCR, Cable, DVD
and Satellite. Select other oper-
ating modes, for the remote to
control external devices.
FRONT
Selects the front video signal if
a device, such as a camcorder
or game player, is connected
to the front video input jack.
DVI
Selects: DVI-DTV and DVI-
PC input sources.
SAP
Selects: Mono, Stereo, and
SAP.
PIPCH-
Changes to next
lower PIP channel
PIP
Toggles between PIP, POP
(Picture-out-of-Picture) and
Twin picture mode.
LIGHT
Illuminates the remote con-
trol keys.
INDICATOR LIGHTS
Show active remote mode
every time any button is
pressed.
D
E
DESCRIPTION OF CONTROLS

- 9 -
Remote Control Functions in TV Mode
1 2 3
4 5 6
7 8 9
0
TV
MODE LIGHT POWER
TV/VIDEO DVI
RGB
VCR CABLE DVD SAT
MUTE
SWAPPIPCH- PIPCH+
PIP
PIC SIZE
REC STOP
PAUSE
REW
PLAY
FF
MENU EXIT
CC FREEZE
PIP INPUT
VOL CH
SURF
SAP VIDEO
C/S HD2C/S HD1
FRONT
SKIP
ENTER
CH RTN
POWER
Turns your TV or any other
programmed equipment on
or off, depending on mode.
CHANNEL UP/DOWN
Scrolls through available chan-
nels in CH. Scan memory.
NUMBER KEYPAD
For direct channel selection and
programming functions.
ENTER
When in the menu system
and other on-screen dis-
plays, selects highlighted
options.
RECORD, PAUSE, REW,
FFWD, PLAY, STOP
Control the functions on your VCR.
VOLUME UP/DOWN
Increases/decreases the sound
level.
PIC SIZE
Changes the screen format or
aspect ratio.
SKIP
Playing CDs: Selects
songs.
Playing DVDs: Selects
movie chapters.
C/S HD1,HD2
Selects ColorStream HD signal
sources, such as DVD or HD receiver.
ENTER
When in the menu system and
other on-screen displays,
selects highlighted options.
CH RTN
Tunes to the last channel
viewed.
CC
Selects a closed caption mode
for displaying captioning infor-
mation if available on program.
PIP INPUT
Selects the input source for the
sub picture.
RGB
Selects: RGB-DTV and
RGB-PC input sources.
DESCRIPTION OF CONTROLS

- 10 -
On-Screen Displays
This page describes your on-screen display and information banner options.
10 AM 3:00
TV 13
MONO
TV 6
Main Channel Display
Displays current channel number.
Channel Label
If a channel label has been
set, then it will appear here.
PIP Display
This display
appears when
PIP is active.
Volume
Volume level is displayed while
adjusting the sound.
Mute
Appears
when sound
is muted.
Time
Appears when
pressing the
enter button.
ABC
DESCRIPTION OF CONTROLS

- 11 -
Front Panel Controls
124
3678
5
POWER
MENU
ENTER (Same as ENTER button on your
remote control)
VOLUME UP / DOWN
CHANNEL UP / DOWN
Operation indicator.
Lamp indicator.
Temperature indicator.
1
2
3
4
5
6
7
8
See menu pages for instructions on using the
on-screen menus.
The POWER, MENU, ENTER, VOLUME, and
CHANNEL buttons work just as they do on
your remote control.
If TV is moved from cold to normal room tem-
perature, condensation may form inside TV,
wait 6~7 hours for the TV to adjust to room
temperature before turning it on.
W
W
W
DESCRIPTION OF CONTROLS

- 12 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
This instruction is for the application to the DLP
Projection(Chassis: MB-042G).
2. Notes
(1) The power source insulation of this DLP Projection is not
charging type and you may not use the transformer for
insulation. But you’d better adjust the set after operating it
with insulation transformer between power supply cable
and input part of the set for protecting the adjusting
equipments.
(2) The adjustment must be performed under the correct
sequence.
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep AC 120V,
60Hz in adjusting.
(5) The set must be operated for 5 minutes preliminarily
before adjustment if there is no specific designation.
The preliminary operation must be performed after
receiving 100% white pattern,but reception of the moving
picture may also be possible in unavoidable case.
3. Composition of Adjustment Mode
(1) All adjustment mode are entered by pressing the ADJ key
on the remore control,after adjustment pess the ADJ key to
come out.
(2) Below picture is screen composition when press the first
ADJ key.
(3) As shown <Fig. 1>, using the (CH+ (D), CH- (E)) key,
select to item press the ENTER or VOLUME+ (G) key to
enter the appropriate item and operate the adjustment.
(4) Change the value of adjustment with using the volume
+(G), volume -(F) key after select adjustment item one
more using the (CH+ (D), CH- (E)) key in ADJ Mode.
(5) Press the ADJ key to come out after adjustment.
(6) Preparation for Adjustment
1) Connect the power to TV Set and set the status of
“Power on”.
2) Heat-Run must operate over 5 minitues before
adjustment.
4. Driver Board Bin Setting
See Bias Voltage Bin on the DMD as shown <Fig. 2> and
adjust the switch on the lower Driver Board as shown <Fig.
3>.
<Fig. 2> DMD Marking Locations
<Fig. 1> Adjustment Mode OSD
<Fig. 3> Driver Board Bin Setting

- 16 -
ADJUSTMENT INSTRUCTIONS
11. Screen Position Adjustment
11-1. Required Test Equipments
Remote Control for Adjustment
11-2. Horizontal Position Adjustment
(1) Press ADJ key on the remote control to enter the
adjustment mode.
(2) Select the POSITION of the adjustment menu.
(3) Appear the adjustment pattern as below figure.
(4) Change data with using the VOLUME key on the remote
control in order to be left/right semmetry screen.
(5) In case of over variable range is N.G.
11-3. Vertical Position Adjustment
(1) Change data with using the CHANNEL key on the remote
control in order to be upper/down semmetry screen.
(Refer to <Fig. 14>)
(2) In case of over variable range is N.G.
[After adjustment completed, recieve NTSC-M Digital Pattern
and check the adjusment level.
12. White Balance Adjustment
(Day Light Mode) : R fixation
12-1. Required Test Equipments
CA110 or CA210
12-2. White base value (Medium)
x = 0.283¡0.01, y = 0.297¡0.01
12-3. Adjustment Sequence
(1) Install the equipment(CA110) be 20cm(CA210: 5cm) away
from screen center.
(2) Select White balance by pressing ADJ Mode Key on
Remote control.
(3) Warm(6500cK) : x = 0.313, y = 0.320
1) R Gain 110 fixation
2) Adjust white balance changing G, B gain.
3) Offset fixation R/G/B --> -8, -10, -8
(4) Medium(9300cK) : x = 0.283, y = 0.297
1) R Gain 112 fixation
2) Adjust white balance changing G, B gain.
3) Offset fixation R/G/B --> -11, -11, -8
(5) Cool(12000cK) : x = 0.275, y = 0.277
1) R Gain 112 fixation
2) Adjust white balance changing G, B gain.
3) Offset fixation R/G/B --> -12, -13, -8
* Reference : Spoke Func. -> 0
Gamma table -> 0
Lamp Type -> 1(OSR2/PHIL)
Img. Orient. -> 0
H Position: 199
V Position: 15
<Fig. 13> Pattern for Screen Adjustment
Adjustment
Adjustment
<Fig. 14>

- 17 -
ADJUSTMENT INSTRUCTIONS
13. CWI (Color Wheel) Adjustment
13-1. Required Test Equipments
Remote control for adjustment
13-2. Preparation for Adjustment
(1) Connect the power at TV set to turn set on.
(2) Using the remote control, enter from ADJUST to CWI.
(Base value: 250)
13-3. Adjustment
(1) Using the Volume key, adjust CWI-Pat. 1 to the left/right.
(2) As adjustment, check the appearance noise in the TEST
Pattern.
Setting the value reduced 3~4 step at a GREEN noise
disappearing spot.
(3) Using CH UP/DOWN key of th remote control, enter the
RED PATTERN.
(4) Check the RED Pattern to uniform. After checking unless
abnormality do OK.
[As temperature is different sensitivity, change angle of the
color wheel. At this time, the adjustment is done because color
may be changed.
14. Main/Sub Contrast Adjustment
14-1. Preparation for Adjustment
(1) Connector RF-NTSC Cable to rear terminal.
(2) Confirms picture probably is the normal.
14-2. Adjustment
(1) Using the remote control, enter from ADJUST to Contrast.
(Base value: MAIN-135, SUB-46)
(2) Select the adjustment item of MAIN/SUB using CH +/- key.
(3) Revises the contrast of MAIN/SUB using VOL +/- key.
(4) The field and the letters are distinguished.
The field and the letters are distinguished.
Adjust to be difference of the MAIN/SUB it is few most.
14-3. Overseas Factory Production
Contrast Adjustment Method
(1) Do the same method as above method.
(2) Make the as same below pattern in VHF 6CH using RF
MODULATOR and PATTERN GENERATOR.
(3) Adjust to become dividing 15 and 16 Gray of Main/Sub
screen .
(4) Adjust to be identical Main/Sub contrast of MAX 16Gray.
(5) Make the adjustment pattern refer to <Fig. 17>.
starting point of noise
(appearance GREEN)
<Fig. 16> TEST Pattern(RED Pattern)
<Fig. 15> TEST Pattern(Lamp Gray Pattern)
<Fig. 17> 16Gray Scale/H Pattern

- 30 -
304
303
305
121
300
520 560
540
501
301
310
650
120
400
430
401
402
681 680
670
630
700
410
550
503
640
602
580
581
174
502
530
720
601
600
570
571
572
620
610
621
730
EXPOLODED VIEW

- 31 -
EXPOLODED VIEW PARTS LIST
CAUTION:
The international hazard symbols “ ” in the schematic diagram and the parts list designate components which
have special characteristics important for safety and should be replaced only with types identicall to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these comoinents, read carefully the PRODUCT SAFETY NOTICE.
Do not degrade the safety of the receiver through improper servicing
NOTICE:
•The parts number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
•The P.C. board assembly with
∗ mark is no longer available after the end of the production.
LOCA. NO. PART NO. DESCRIPTION REFERENCE NO.
120 AZ684014 SPEAKER, WOOFER C080P23K1450 ESTEC WOOFER 8OHM 15/25W 6400WESC01A
121 AZ684015 SPEAKER, TWEETER D016D01K1450 8OHM 15/25W 85DB 50 NON 6400DESA01A
174 AZ684016 POWER CORD, UL/CSA3000MM 3P 3000MM HUG BLACK 500MH 7A 6410VUH004A
300 AZ780010 CABINET, DN-44SZ80L LCD PJT FRONT 3090V00556A
301 AZ780011 BRACKET ASSEMBLY, SPEAKER RU-44SZ83D MB042G GRILLE TOSHIBA 4811V00174A
303 AZ780012 SOPPORTER, SCREEN AL BAR U/L 4980V00A29G
304 AZ780013 SOPPORTER, SCREEN AL BAR R/L 4980V00A29H
305 AZ780014 SCREEN ASSEMBLY, WLF DN-44SZ80L 991*564*3.4 3351V00020A
310 AZ780015 BUTTON, CONTROL RU-44SZ83D ABS, HF-380 7KEY TOSHIBA OEM 5020V01025A
400 AZ780016 BACK COVER,DN-44SZ80L NB-042A 3808V00455A
401 AZ780017 COVER, DN-44SZ80L ABS POWER CODE 3550V00424A
402 AZ780018 COVER, LAMP RU-44SZ83D HIPS 40AF TOSHIBA 3550V00423D
410 AZ780019 COVER, DN-44SZ80L HIPS 40AF RU-44SZ83D 3550V00425B
430 AZ780020 MIRROR, REFLECTION AVATEC GLASS FRONTSIDE 940 (H1)*500 (H2)*498 (V)*3.0 (T) 1ST 44 5018V00039F
501 AZ780021 FRAME, ABS AF-303S RN-48SZ40H MAIN CHASSIS 3210V00165B
502 AZ780022 FRAME, CHASSIS HIPS 40AF DN-44SZ60D SMPS 3210V00191A
503 AZ780023 BRACKET ASSEMBLY, REAR AV RU-44SZ83D NON BOARD TERMINAL 4811V00125G
520 AZ680001 PCB ASSEMBLY, MAIN MB-042G M/I FOR RU-44SZ83D(TOSHIBA OEM) 6871VMMT51A
530 AZ680002 PCB ASSEMBLY, POWER SMPS MB042G M/I FOR RU-44SZ83D (TOSHIBA OEM) 6871VPMA84A
540 AZ680003 PCB ASSEMBLY, SUB TUNER MB-042G M/I FOR RU-44SZ83D (TOSHIBA OEM) 6871VSMAAJA
550 AZ680004 PCB ASSEMBLY, SUB DIGITAL MB-042G M/I FOR RU-44SZ83D (TOSHIBA OEM) 6871VSMT19A
560 AZ680005 PCB ASSEMBLY, SUB MB-042G COMPONENT M/I FOR RU-44SZ83D (TOSHIBA OEM) 6871VSMAAHA
570 AZ680006 PCB ASSEMBLY, SUB CRM MB04EA DRIVE M/I ASSY FOR LVDS HD2 (TOSHIBA) 6871VSMZ44F
571 AZ780024 SHIELD, COVER DN-44SZ60D NB03KB AL DRIVER FRONT DLP720P SHILD CASE 4814V00394B
572 AZ780025 SHIELD ASSY,DN-44SZ60D NB03KB SUS, SHILD CASE DRIVE BOTTOM 4814V00434B
580 AZ684017 FAN,DC F6025S06B2-RH DONGYANG 60*&*25 6 2000RPM.650MM 5900V06007A
581 AZ780026 SUPPORTER, FAN SPCC(CR), DN-44SZ60H 4980V00813B
600 AZ684002 CHASSIS ASSEMBLY, ENGINE MB-042G 720P FOR RU-44SZ83D (TOSHIBA OEM) 3141VEN044A
601 AZ780027 SUPPORTER, SMPS EGI RU-44SZ83D 4980V01175A
602 AZ780028 SUPPORTER, OPTICAL EGI ENGINE DLP RZ-44SZ80DB 4980V00817B
610 AZ684001 LAMP UNIT TBL4-LMP
620 AZ684018 FAN, DC G12225S06B2-FS DONGYANG 120*120*25 6V 1000RPM.1000MM 5900V12005A
621 AZ780029 BRACKET, FIXER RN-44SZ50H NB03JA ABS, AF-303S FAN HOLDER 4810V00813A
630 AZ680007 PCB ASSEMBLY, SUB P/AMP NB042A DN-44SZ80L 6871VSN221E
640 AZ684019 BALLAST, EUC-120P/H11 PHILIPS 20KV 6316000007A
650 AZ680008 PCB ASSEMBLY, SUB CONT MB042A 80L CONTROL 6871VSME75A
670 AZ680009 PCB ASSEMBLY, SUB MB042A 80L CASE DET 6871VSME03D
680 AZ680010 PCB ASSEMBLY, SUB MB042A SIDE AV DN-44SZ80L 6871VSN220B
681 AZ680011 BOARD ASSY, RU-44SZ83D MB042G TOSHIBA OEM 3500V00061Z
700 AZ680012 PCB ASSEMBLY, SUB INTER MB042G FOR RU-44SZ83D 6871VSME82G
720 AZ680013 PCB ASSEMBLY, POWER SMPS MB042G AC INPUT M/I (TOSHIBA OEM) 6871VPMA85A
730 AZ680014 PCB ASSEMBLY, SUB SENSOR MB03CC HD2 7SEGMENT SENSOR B/D 6871VSMW40E

- 48 -
ELECTRICAL REPLACEMENT PARTS LIST
CAUTION:
The international hazard symbols “ ” in the schematic diagram and the parts list designate components which
have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list.The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE.
Do not degrade the safety of the receiver through improper servicing.
NOTICE:
•The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model
number and Description.
•The P.C. board assembly with
∗ mark is no longer available after the end of the production.
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the REFERENCE NO. means as follows;
CC, CX, CK, CN : Ceramic RD : Carbon Film
CQ : Polyestor RS : Metal Oxide Film
CE : Electrolytic RN : Metal Film
RF : Fusible
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
IC
IC1 AZ681001 M37151EFFP 42P SSOP R/TP MICOM 0ICTMMI057A
IC1 AZ681002 GP2S40 SHARP 4P 0IMCRSH003A
IC1 AZ681003 TC7S14F(T5L,T)5P 0IPRPTO002A
IC100 AZ681004 74HC14D 14SOP 0IPH741400E
IC100 AZ681005 MC34063ADR2G SO-8P DC-DC 0IPMGON013B
CONVERTER
IC1000 AZ681006 M62320FP 16P SOP 0IMI623200B
IC1001 AZ681006 M62320FP 16P SOP 0IMI623200B
IC1004 AZ681007 THC63LVD104A 64P 0IMCRTH003A
IC101 AZ681008 KIA278R05PITO220IS, 4P 0IMCRKE006A
IC102 AZ681009 M306V7FJFP 100P 0IMCRM1070B
IC102 AZ681010 KIA7809APITO220 ST 3P 9V 0IKE780900M
IC103 AZ681011 24LC256-I/SM 8P 256K IIC SERIAL 0IMP242560A
EEPROM
IC104 AZ681012 KIA7027AF 3, SOT-89 TP RESET 0IKE702700D
IC 2.7V
IC105 AZ681013 ST3232CDR SOP16 RS232 0IMCRSG010A
IC106 AZ681014 THC63LVD103 64P 0IMCRTH002A
IC107 AZ681015 EL2250CS-T7 8P 0IMCRET002B
IC1200 AZ681016 KIA78R05F 5PIN DPAK R/TP 1A, 5V 0IPMGKE030A
IC1201 AZ681017 CXA2181Q 48PVIDEO SYNC 0IMCRSO025A
SELECTOR
IC2 AZ681018 TC7S14F(T5L,T)5P 0IPRPTO002A
IC2 AZ681019 KIA78R33API 4PTO220 ST 3.3V 0IMCRKE019A
IC200 AZ681020 CXA2069Q QFP64 BK 12C BUS AV 0ISO206900A
S/W
IC3 AZ681021 KIA78R05API 4PTO220 ST 5V 0IMCRKE018A
IC300 AZ681022 VPC3230D C5 80PVIDEO 0IIT323000E
PROCESSOR
IC301 AZ681023 M74HC123RM13TR 16P 0ISTLSSG009A
IC302 AZ681024 XC95144XL-10TQ100C 3.3V 0IMCRXL003A
IC304 AZ681025 P82B715T 8SOP 0IPH827150A
IC305 AZ681026 AT24C02N-10SI-2.7 8P 0IMMRAL014B
IC306 AZ681027 AD9883AKST-110 80P DIGITAL 0IMCRAD002A
BOARD
IC307 AZ681028 SIL 169CT100 100P 0IMCRS5003A
IC4 AZ681029 KA75420ZTA 3P TO-92 TP 4.2V 0IFA754207A
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
IC404 AZ681008 KIA278R05PITO220IS, 4P 0IMCRKE006A
IC405 AZ681030 KIA278R33PITO220IS, 4P 0IMCRKE006B
IC406 AZ681030 KIA278R33PITO220IS, 4P 0IMCRKE006B
IC407 AZ681031 KIA278R25PI 2.5V 2ATO220IS, 4P 0IPMGKE045A
IC409 AZ681032 KIA278R12API 4PTO220IS 0IMCRKE003B
IC5 AZ681033 AT24C16AN-10SI-2.7 8P 0IMCRAL006A
IC500 AZ681034 LGDT1502M LG IC 304P 0ICTMLG003C
IC501 AZ681035 HY57V643220C(L)T-6 86P 0IMMRHY033A
IC502 AZ681036 SN74LVC00AD 14SOP 0ITI740000Q
IC502 AZ681037 X1272-0346 251P 0IZZVF0020B
IC503 AZ681038 LGDT1901A LG IC 24P 0ICTMLG013A
IC504 AZ681035 HY57V643220C(L)T-6 86P 0IMMRHY033A
IC600 AZ681039 MSP3440G QA B8V3 80 SOUND IC 0IMCRMN014A
IC601 AZ681040 KA4558D 8SOP OP AMP 0ISS455880A
IC602 AZ681029 KA75420ZTA 3PTO-92TP 4.2V 0IFA754207A
IC700 AZ681041 2503227-001(DDP1010) 529P 0IMCRT011A
IC701 AZ681030 KIA278R33PITO220IS, 4P ST 3.3V 0IMCRKE006B
IC701 AZ681042 AT49BV8192A-90TI 48P 0IMMRAL015C
IC702 AZ681030 KIA278R33PITO220IS, 4P ST 3.3V 0IMCRKE006B
IC702 AZ681043 K4S161622E-TC80 50TSOP 0ISS416162C
IC702 AZ681044 KA2903 FAIRCHILD 8SOP 0IMCRFA003A
IC703 AZ681031 KIA278R25PI 2.5V 2ATO220IS, 4P 0IPMGKE045A
IC703 AZ681045 UPD64011AGM-8ED-A NEC LQFP 0IMCRNE045A
160P
IC705 AZ681033 AT24C16AN-10SI-2.7 8P 0IMCRAL006A
IC706 AZ681046 LA4282 12S 2CHX10W AUDIO AMP 0ISA428200A
IC707 AZ681032 KIA278R12API 4PTO220IS ST 12V/1A 0IMCRKE003B
IC708 AZ681030 KIA278R33PITO220IS, 4P ST 3.3V 0IMCRKE006B
IC709 AZ681031 KIA278R25PI 2.5V 2ATO220IS, 4P 0IPMGKE045A
IC800 AZ681047 K4R271669F-TCS8 54P 0IMMRSS053B
IC801 AZ681048 CDCR83 24P 0IMCRTI014A
IC802 AZ681049 74VIT125CTR 5P S0T323-5L 0IMCRSG007A
IC803 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC804 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC805 AZ681051 MAX708SCSA 8P 0IMCRMX001A
IC806 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC807 AZ681051 MAX708SCSA 8P 0IMCRMX001A

- 49 -
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
IC808 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC809 AZ681052 LD1086DT15TR 2P 0IPMGSG018C
IC810 AZ681053 SC15651ST-1.8 3P SOT223 0IMCRSJ001A
IC810 AZ681054 SMA-E1017 3P 0IMCRSK004A
IC830 AZ681055 PC817XF3 4D PHOTO COUPLER 0ISH817300B
IC850 AZ681056 PQ30RV21TO-220 0ISH302122A
IC851 AZ681057 KA431Z FAIRCHILD 3DIP 0IMCRFA007A
IC870 AZ681057 KA431Z FAIRCHILD 3DIP 0IMCRFA007A
IC900 AZ681058 LGDP4410 LG IC 176P 0ICTMLG018A
IC900 AZ681059 2503253-0003(DAD1000-3) 80P 0IMCRTI012B
IC901 AZ681060 SNSH6742CFA(P32J6742PAG) 64P 0IMCRTI013A
IC906 AZ681049 74VIT125CTR 5P S0T323-5L 0IMCRSG007A
IC907 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC908 AZ681050 74LX1G14CTR 5P SOT323-5L 0IMCRSG008A
IC909 AZ681061 74LX1G07CTR 5P SOT323-5L 0IMCRSG008B
IC910 AZ681049 74VIT125CTR 5P S0T323-5L 0IMCRSG007A
TRANSISTOR
IC903 AZ580001 FDS6930A 8P SO-8 30V 5.5A 0TFFC80015A
IC904 AZ580001 FDS6930A 8P SO-8 30V 5.5A 0TFFC80015A
IC905 AZ580001 FDS6930A 8P SO-8 30V 5.5A 0TFFC80015A
Q100 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q100 AZ580003 BSS83 0TR830009BA
Q1000 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1001 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1002 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1003 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1004 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1005 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q101 AZ580003 BSS83 0TR830009BA
Q102 AZ580004 CHIP KRC102S SOY-23 0TR102009AG
Q103 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q104 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q105 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q107 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1201 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1202 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1203 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1204 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1205 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1206 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1208 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q1209 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1210 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q1211 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1213 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1218 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q1219 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1222 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1223 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1224 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q1225 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q200 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q201 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q202 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q203 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q204 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
Q205 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q206 AZ580006 KRA102S SOT23 CHIPTR 0TR102008AA
Q207 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q208 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q209 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q210 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q211 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q212 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q302 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q305 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q306 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q307 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q308 AZ580003 BSS83 0TR830009BA
Q309 AZ580003 BSS83 0TR830009BA
Q310 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q311 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q501 AZ580003 BSS83 0TR830009BA
Q502 AZ580003 BSS83 0TR830009BA
Q600 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q601 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q602 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q603 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q604 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q701 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q703 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q704 AZ580005 CHIP 2SA1504S(ASY)KEC 0TR150400BA
Q801 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q801 AZ580007 STW20NK80ZTO-247 500V 17A 0TFSG10004A
Q802 AZ580002 CHIP 2SC3875S(ALY)KEC 0TR387500AA
Q830 AZ580008 STW8NK80ZTO-247 800V 6.2A 0TFSG10003A
Q832 AZ580009 KTC4370A-YTO-220IS KEC 0TR437000BA
Q840 AZ580010 KTC3227-Y,TP(KTC1627A), KEC 0TR322709AA
Q852 AZ580011 KSC945C-YTO92 50V 150MA 0TR945009AA
Q871 AZ580012 KTA1024-Y(KTA949)TP KEC 0TR102409AB
Q872 AZ580010 KTC3227-Y,TP(KTC1627A), KEC 0TR322709AA
DIODE
D1 AZ480001 LED,LTL-30EWJ 0DLLT0260AA
D1 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D100 AZ480003 SDC15 SOT23 12.8V 0DRSE00038A
D100 AZ480004 B140A 40V 1A 30A.SEC 0.5MA 0DRDI00148
D102 AZ480005 SD05.TC SOD323 5V 5A 15A 0DR050008AA
D103 AZ480005 SD05.TC SOD323 5V 5A 15A 0DR050008AA
D104 AZ480005 SD05.TC SOD323 5V 5A 15A 0DR050008AA
D105 AZ480003 SDC15 SOT23 12.8V 0DRSE00038A
D106 AZ480005 SD05.TC SOD323 5V 5A 15A 0DR050008AA
D2 AZ480001 LED,LTL-30EWJ 0DLLT0260AA
D201 AZ480006 1N4148TP GRANDE 0DD414809ED
D3 AZ480001 LED,LTL-30EWJ 0DLLT0260AA
D3 AZ480007 CHIP KDS226 SOT-23 0DD226239AA
D300 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D4 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D5 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D6 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D700 AZ480008 1SS133T-72 TP DO34 90V 0DS113379BA
D704 AZ480008 1SS133T-72 TP DO34 90V 0DS113379BA
D706 AZ480008 1SS133T-72 TP DO34 90V 0DS113379BA
ELECTRICAL REPLACEMENT PARTS LIST

- 50 -
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
D707 AZ480008 1SS133 T-72 TP DO34 90V 0DS113379BA
D708 AZ480008 1SS133 T-72 TP DO34 90V 0DS113379BA
D709 AZ480008 1SS133 T-72 TP DO34 90V 0DS113379BA
D710 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D711 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D712 AZ480002 KDS184S CHIP 85V 300MA 0DD184009AA
D801 AZ480009 RBV606 600V 6A 150A NA 10UA 0DD606000AA
D831 AZ480010 EU1AV(1) 0DD100009AU
D832 AZ480010 EU1AV(1) 0DD100009AU
D834 AZ480011 EG01C 1000V 0.5A 10A 0DR010009AA
D835 AZ480006 1N4148TP GRANDE 0DD414809ED
D840 AZ480006 1N4148TP GRANDE 0DD414809ED
D851 AZ480012 FML-G12S 0DD120000BB
D861 AZ480012 FML-G12S 0DD120000BB
D871 AZ480013 FML-G22STO220 200V 0DD220000AC
D881 AZ480012 FML-G12S 0DD120000BB
D891 AZ480014 FML-G14STO220 400V 0DRSA00170A
D901 AZ480015 BAT54SWT1 60V 3A 4A.SEC.A 0DRON00088A
D902 AZ480015 BAT54SWT1 60V 3A 4A.SEC.A 0DRON00088A
D903 AZ480015 BAT54SWT1 60V 3A 4A.SEC.A 0DRON00088A
D904 AZ480015 BAT54SWT1 60V 3A 4A.SEC.A 0DRON00088A
D905 AZ480015 BAT54SWT1 60V 3A 4A.SEC.A 0DRON00088A
D906 AZ480016 BAV99RWT1 SC-75 70V 215MA 0DSON00028A
D907 AZ480017 MBRD320RL SC-75 30V 150MA 0DRON00098A
D908 AZ480018 ZENERS, SMZJ3793B 0DZGS00108A
D909 AZ480019 SS26 DC-214AC 60V 2A 0ZRGS00328A
Q801 AZ480020 FMG-36S 2.2V 100NSEC 1.0MA 0DR360000AA
XD204 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD01 AZ480005 SD05.TC SOD323 5V 5A 15A 0DR050008AA
ZD1 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD10 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD2 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD201 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD202 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD203 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD204 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD3 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD4 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD5 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD6 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
ZD600 AZ480022 ZENERS, MTZJ5.6B 0DZ560009CF
ZD601 AZ480022 ZNERS, MTZJ5.6B 0DZ560009CF
ZD839 AZ480023 ZENERS, MTZJ30B 0ZD300009BB
ZD9 AZ480021 ZENERS, MTZJ6.2B 0DZ620009BB
CAPACITOR
C1 AZ180002 47UF STD 16V M 0CE476DF618
C1 AZ180001 22UF STD 16V M 0CE226DF618
C100 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C100 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C101 AZ180005 10UF STD 16V M 0CE106DF618
C101 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C103 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C109 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C110 AZ180005 10UF STD 16V M 0CE106DF618
C111 AZ180002 47UF STD 16V M 0CE476DF618
C112 AZ180008 100UF STD 16V M 0CE107DF618
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
C113 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C115 AZ180005 10UF STD 16V M 0CE106DF618
C116 AZ180009 47UF KME 50V M 0CE476BK618
C117 AZ180002 47UF STD 16V M 0CE476DF618
C118 AZ180008 100UF STD 16V M 0CE107DF618
C120 AZ180008 100UF STD 16V M 0CE107DF618
C1200 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1201 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1203 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1204 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1206 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1207 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1208 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1209 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C121 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C1213 AZ180010 10UF MV 16V 20% 0CE106VF6DC
C1214 AZ180011 220UF MV 16V 20% 0CE227VF6DC
C1217 AZ180012 100UF MVG 16V M 0CE107SF6DC
C123 AZ180013 100UF STD 50V M 0CE107DK618
C1244 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C1246 AZ180014 47UF MVG 16V M 0CE476SF6DC
C1249 AZ180014 47UF MVG 16V M 0CE476SF6DC
C1257 AZ180014 47UF MVG 16V M 0CE476SF6DC
C1259 AZ180014 47UF MVG 16V M 0CE476SF6DC
C126 AZ180009 47UF KME 50V M 0CE476BK618
C129 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C130 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C132 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C134 AZ180002 47UF STD 16V M 0CE476DF618
C136 AZ180009 47UF KME 50V M 0CE476BK618
C139 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C145 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C147 AZ180008 100UF STD 16V M 0CE107DF618
C149 AZ180015 100UF STD 25V M 0CE107DH618
C15 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C150 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C151 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C162 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C2 AZ180016 10000PF D 16V 20% 0CN1030F679
C20 AZ180015 100UF STD 25V M 0CE107DH618
C200 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C200 AZ180014 47UF MVG 16V M 0CE476SF6DC
C201 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C202 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C203 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C203 AZ180014 47UF MVG 16V M 0CE476SF6DC
C204 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C205 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C205 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C206 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C207 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C207 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C208 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C209 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C209 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C210 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C210 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C211 AZ180007 1UF 2012 16V 20% 0CK105DF64A
ELECTRICAL REPLACEMENT PARTS LIST

- 51 -
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
C211 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C212 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C212 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C213 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C213 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C214 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C214 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C215 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C215 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C216 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C217 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C219 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C223 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C224 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C225 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C226 AZ180018 220UF STD 16V M 0CE227DF618
C227 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C229 AZ180001 22UF STD 16V M 0CE226DF618
C23 AZ180008 100UF STD 16V M 0CE107DF618
C231 AZ180008 100UF STD 16V M 0CE107DF618
C237 AZ180017 220000PF 2012 16V 10% 0CK224DF56A
C238 AZ180014 47UF MVG 16V M 0CE476SF6DC
C24 AZ180002 47UF STD 16V M 0CE476DF618
C249 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C260 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C261 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C262 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C27 AZ180002 47UF STD 16V M 0CE476DF618
C335 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C338 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C339 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C344 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C345 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C358 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C359 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C363 AZ180019 82000PF 2012 50V 10% 0CK823DK56A
C381 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C394 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C395 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C405 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C5 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C508 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C510 AZ180006 22UF MVG 16V 20% 0CE226SF6DC
C550 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C565 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C570 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C571 AZ180004 10UF MVG 16V 20% 0CE106SF6DC
C572 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C574 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C575 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C576 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C580 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C582 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C583 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C584 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C606 AZ180008 100UF STD 16V M 0CE107DF618
C609 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C610 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
LOCA.NO. PART NO. DESCRIPTION REFERENCE NO.
C611 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C612 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C614 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C615 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C616 AZ180008 100UF STD 16V M 0CE107DF618
C616 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C617 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C618 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C619 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C620 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C621 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C621 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C622 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C622 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C623 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C624 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C625 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C626 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C627 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C628 AZ180005 10UF STD 16V M 0CE106DF618
C628 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C629 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C630 AZ180005 10UF STD 16V M 0CE106DF618
C630 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C631 AZ180005 10UF STD 16V M 0CE106DF618
C631 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C632 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C633 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C634 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C635 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C636 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C637 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C638 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C639 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C640 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C641 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C642 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C643 AZ180002 47UF STD 16V M 0CE476DF618
C643 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C644 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C645 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C646 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C647 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C648 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C648 AZ180021 3.3UF STD 50V 20% 0CE335DK618
C649 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C650 AZ180022 27PF 1608 50V 5% 0CC270CK41A
C651 AZ180022 27PF 1608 50V 5% 0CC270CK41A
C652 AZ180022 27PF 1608 50V 5% 0CC270CK41A
C653 AZ180022 27PF 1608 50V 5% 0CC270CK41A
C654 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C655 AZ180020 0.1UF 1608 16V 10% 0CK104CF56A
C664 AZ180021 3.3UF STD 50V 20% 0CE335DK618
C668 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C669 AZ180007 1UF 2012 16V 20% 0CK105DF64A
C670 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C671 AZ180003 4.7UF STD 50V 20% 0CE475DK618
C673 AZ180021 3.3UF STD 50V 20% 0CE335DK618
ELECTRICAL REPLACEMENT PARTS LIST