Toshiba MV13P2 User manual

TELEVISION/VCR COMBINATION
Before operating the unit, please read this manual thoroughly.
MV13P2
OWNER’S MANUAL
ATTENTION
If you purchase a universal remote control from your local retailer, please
contact the remote manufacturer for the required programming code.
TV/CABLE MODE SELECTION
When shipped from the factory, the TV/CABLE selection is set to the “CABLE”
(Cable Television) position.
If not using Cable TV, set this selection to the “TV” position.
5L80101C COV-IN 20/4/04, 16:181

The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock.
Theexclamationpointwithinanequilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
theliteratureaccompanyingtheappliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC (Federal Communications Commission) Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with the
FCC (Federal Communications Commission) Rules could void the user's authority to operate this
equipment.
COPYRIGHT: It is permissible to record television programs, films, video tapes and other material only in the event
that third party copyrights and other rights are not violated.
WARNING: Unauthorized recording of copyrighted television programs, films, video cassettes and other materials
may infringe the rights of copyright owners and be contrary to copyright laws.
5L80101C COV-IN 20/4/04, 16:182

1
IMPORTANT SAFEGUARDS
S3126A
PORTABLE CART WARNING
(symbol provided by RETAC)
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause haz-
ards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation, and to ensure reliable operation of
the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never
be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure
of the type of power supply to your home, consult your appliance dealer or local power company. For units
intended to operate from battery power, or other sources, refer to the respective pages on this Owner’s Manual
for their operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire
grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power
outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
5L80101C P01-09 20/4/04, 16:181

2
IMPORTANT SAFEGUARDS (CONTINUED)
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit
due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or
power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact
with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out
parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded
to provide some protection against voltage surges and built-up static charges, Section 810 of the National
Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding
electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the
manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
5L80101C P01-09 20/4/04, 16:182

3
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC-NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
IMPORTANT RECYCLING INFORMATION
This product uses both Cathode Ray Tube (CRT) and other components
that contain lead. In your community there might be regulations that
require you to dispose these materials properly under environmental
considerations. Please contact your local authorities, or the Electronic
Industries Alliance (http://www.eiae.org) for disposal or recycling
information.
5L80101C P01-09 20/4/04, 16:193

4
FEATURES
Color TV With Video Cassette Recorder - Unique space saving design combines a color TV and a video cassette
recorder.
High Quality Picture Technology - This TV/VCR equipped “HQ” incorporates VHS High Quality technology. Abuilt-in detail
enhancer is used to boost the recorded signal and provide picture quality during playback. It is compatible with other VHS
video cassette recorders.
181 Channel Tuner - Receives standard VHF and UHF broadcast channels and up to 113 cable channels. The actual
number of channels received depends upon channel reception in your area or your cable system.
Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for hearing
impaired viewers.
8-Programs/1-Month Programmable Timer With Everyday/Every Week Capability - The built-in timer allows automatic
absentee recording of up to 8 TV programs within 1 month. It is also possible to record a program which is broadcast at the
same time everyday or every week.
Starting Setup - It leads you the Language selection, TV/CABLE selection,Auto channel memory and Auto clock setting
automatically.
Automatic Clock Set - Once your TV/VCR is plugged into theAC outlet, it automatically sets the correct date and time.
On-Screen TV Display And VCR Programming - When you select a channel or make other changes, the TV will show an
indicator on the screen for a few seconds. Timer recording can be programmed and confirmed on the screen.
Picture Adjustments Using The Remote Control - The On-Screen display allows remote control adjustment of BRIGHT-
NESS, CONTRAST, COLOR, TINT and SHARPNESS.
Picture Preference - You can select four picture modes (Sports, Standard, Movie and Memory).
Automatic Playback/Rewind-Stop-Eject - When loading a cassette tape without the erase prevention tab, this TV/ VCR
will automatically play back the cassette tape at the correct speed. When a tape reaches its end during play-back, recording
(except during OTR and Timer Record) and fast forward, it will automatically stop, rewind, stop and eject the tape.
Programmable ON/OFF Timer - Allows you to automatically turn on or off the TV/VCR at a set time.
Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed up to 120 minutes to turn
off automatically.
Automatic Repeat Play System - When Auto Repeat option is turned on, the TV/VCR will automatically play back the
same cassette tape repeatedly.
One-touch Timer Recording (OTR) - Simply by pressing the REC buttons, the TV/VCR can be programmed for up to 6
hours of recording with an immediate start.
Front Audio/Video Input Jacks - Input jacks for other video device or playback purpose.
Skip Search - When the SKIP SEARCH button on the remote control is pressed during playback, the TV/VCR will auto-
matically search forward in 30 second increments to a maximum of 3 minutes with each press of the SKIP SEARCH button,
and then return to normal playback.
Index Search - Enables you to locate the beginning of any recording made on the VCR.
2 Speed Picture Search - 3 or 5 times normal speed in SP mode (9X or 15X in SLP).
2 Speed Record Playback - Records and plays two tape speeds (SP, SLP).
Real Time Tape Counter With Zero Return - The counter displays the real tape time and the zero return can be used to
return the tape to a preselected position (00:00:00) while the counter can be used to locate programs.
Digital Auto Tracking - Automatically adjusts tracking during playback for the best possible picture.
On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-screen programming.
V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded with this
information. V-Chip will allow you to set a restriction level.
TV Monitor - When the TV MONITOR button on the remote control is pressed during playback, the TV channel selected on
the TV/VCR can be viewed.
5L80101C P01-09 20/4/04, 16:194

5
TABLE OF CONTENTS
PREPARATION
SAFETY PRECAUTIONS ....................................................................................................................................... 6
LOCATION OF CONTROLS ................................................................................................................................... 8
REMOTE CONTROL .............................................................................................................................................. 9
ANTENNA CONNECTIONS...................................................................................................................................11
CABLE TV CONNECTIONS ................................................................................................................................. 12
STARTING SETUP ............................................................................................................................................... 13
SETTING THE LANGUAGE ................................................................................................................................. 14
AUTO CLOCK SETTING ...................................................................................................................................... 15
MANUAL CLOCK SETTING ................................................................................................................................. 17
TV OPERATION
TV OPERATION.................................................................................................................................................... 18
TO MEMORIZE CHANNELS ................................................................................................................................ 22
SETTING THE V-CHIP ......................................................................................................................................... 25
TO SET THE ON TIMER....................................................................................................................................... 29
TO SET THE OFF TIMER..................................................................................................................................... 30
PICTURE CONTROLADJUSTMENTS ................................................................................................................ 31
ADJUSTING THE PICTURE PREFERENCE ....................................................................................................... 32
PLAYBACK
LOADING AND UNLOADING AVIDEO CASSETTE ............................................................................................ 33
PLAYBACK ........................................................................................................................................................... 35
SPECIAL PLAYBACK ........................................................................................................................................... 37
RECORDING
RECORDING A TV PROGRAM ............................................................................................................................ 39
ONE-TOUCH TIMER RECORDING (OTR) .......................................................................................................... 41
TIMER RECORDING ............................................................................................................................................ 42
OTHER FUNCTIONS FOR THE TIMER RECORDING........................................................................................ 44
ADDITIONAL INFORMATION
USING THE REALTIME TAPE COUNTER .......................................................................................................... 45
USING ZERO RETURN........................................................................................................................................ 46
VIDEO INDEX SEARCH SYSTEM/TO MONITOR A TV PROGRAM ................................................................... 47
DUPLICATING A VIDEO TAPE ............................................................................................................................. 48
RECEPTION DISTURBANCES ............................................................................................................................ 49
PROBLEM AND TROUBLESHOOTING GUIDE................................................................................................... 50
VIDEO HEAD CLEANING..................................................................................................................................... 52
SPECIFICATIONS ................................................................................................................................................ 52
LIMITED WARRANTY .......................................................................................................................................... 53
Please read the descriptions and operating procedures contained in this Owner’s Manual prior to operating
your new TV/VCR.
5L80101C P01-09 20/4/04, 16:195

6
SAFETY PRECAUTIONS
Avoid extreme moisture and dust. The ventilation holes prevent overheating. Do not
block or cover these holes. Especially avoid
covering the holes with soft materials such as cloth
or paper.
If you cause a static discharge when touching the
unit, and the unit fails to function, simply unplug the
unit from the wall outlet, wait a few minutes and
plug it back in. The unit should return to normal
operation.
Avoid extreme heat.
Avoid extreme cold.
Do not place the unit on or near appliances which may
cause electromagnetic interference (e.g. speakers,
etc). Doing so may cause erratic operation of the unit
including picture and/or sound distortion or noise.
MOISTURE CONDENSATION
DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT FOR AT LEAST THREE HOURS WHEN MOISTURE IN
THE AIR CONDENSES ON IT. LET THE UNIT STAND WITH POWER ON (SEE BELOW).
WHAT IS MOISTURE CONDENSATION?
When a cold liquid is poured into a glass, for example, water vapor in the air will condense on the surface of
the glass. This is called moisture condensation.
MOISTURE WILL CONDENSE ON THE UNIT IN THE FOLLOWING CASES;
•When you move the unit from a cold to a warm place.
•After heating a cold room or under extremely humid conditions.
WHEN YOU EXPERIENCE THE ABOVE CONDITIONS,
Plug the power cord into an AC outlet, press the POWER button to turn on
and leave the unit at room temperature until moisture condensation disappears.
Depending on the surrounding conditions, this may take about three hours.
(5˚C)
41˚F
104˚F
(40˚C)
Video Tape
Head Drum
5L80101C P01-09 20/4/04, 16:196

7
Do not insert fingers or any other objects into the
cassette loading slot. Do not spray cleaner or wax
directly on the unit or use forced air to remove dust.
Avoid places subject to strong vibration. Use in
a horizontal (flat) position only.
Keep the unit away from flower vases, sinks, etc.
If liquids should be spilled into the unit, serious
damage will result. If you spill any liquids into the
unit, unplug the AC power cord immediately and
consult qualified service personnel before attempt-
ing to use it again.
When you finish operating the unit, always unload
the cassette and turn off the power.
When you leave your home for a long time, unplug
the AC power cord. To protect the unit from a lightning storm, unplug the AC power cord from the wall outlet and disconnect
the antenna.
TO USEAC POWER
Use theAC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
•Never connect theAC line cord plug to anything other than the
specified voltage (120V 60Hz). Use the attached power cord only.
•If the polarized AC cord does not fit into a nonpolarized AC outlet,
do not attempt to file or cut the blade. It is the user's responsibility
to have an electrician replace the obsolete outlet.
•If you cause a static discharge when touching the unit, and the
unit fails to function, simply unplug the unit from the AC outlet, wait
a few minutes, and plug it back in. The unit should return to
normal operation.
•If theAC cord plug is plugged in for the first time, wait for about 5
seconds before pressing the POWER button.
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other)
AC Outlet
POWER SOURCE
5L80101C P01-09 20/4/04, 16:197

8
ANT.
VOLUMEREC
POWER
CHANNEL PLAY REW FF STOP/EJECT
RECTIMER REC
VIDEO AUDIO
LINE IN
PHONE
LOCATION OF CONTROLS
REAR
DESCRIPTION OF CONTROLS
FRONT
1
10. VOLUME ▲/ ▼buttons - Press to raise or lower
the volume of the sound.
11. CHANNEL ▲/ ▼buttons - Press to select a
channel for viewing or recording.
12. STOP/EJECT button - Press once to stop the tape
in any mode. Press again to eject the tape.
13. FF (Fast Forward) button - In the Stop mode, this
button rapidly winds the tape forward. In the Play
mode, this button activates forward search.
14. AUDIO/VIDEO IN jacks - Audio and video signal
cables from an external source can be connected
here.
REAR:
15. UHF/VHF antenna jack - Connect the 75 ohm
coaxial cable from the antenna or Cable TV service
to this jack.
16. AC power cord - Connect to a 120V, 60Hz outlet.
15
FRONT:
1. Cassette loading slot - To insert or remove a video
tape.
2. POWER button - Press to turn the TV/VCR on or off.
3. TIMER REC indicator - Lights when the unit is in
the Timer Record Mode.
4. REC indicator - Lights up when the TV/VCR is
recording.
5. PLAY button - Press to play a prerecorded tape.
6. REW (Rewind) button - In the Stop mode, this
button rapidly winds the tape backwards. In the Play
mode, this button activates reverse search.
7. PHONE jack - Plug monaural headphones or an
earphone with an 1/8” miniplug into this jack for
private listening.
8. Remote sensor - Signals from the Remote Control
are received here.
9. REC button - Press once to start normal recording.
Additional presses activate One-touch Timer
Recording.
3
11
45
12 13
6
14
72
10
16
8 9
WAIT
5L80101C P01-09 20/4/04, 16:198

9
INPUT
SELECT
SKIP
SEARCH
COUNTER
RESET
CHANNEL
RETURN
DIGITAL
TRACKING PAUSE /STILL
TV MONITOR
SLEEP
ZERO
RETURN
TIMER
REC
CANCEL
MUTE
ENTER
TRACKING
INDEX
EJECT
MENU
SPEEDPROGRAM
CALL
CLOSED
CAPTION
REC
INPUT
SELECT
SKIP
SEARCH
COUNTER
RESET
CHANNEL
RETURN
DIGITAL
TRACKING PAUSE /STILL
TV MONITOR
SLEEP
ZERO
RETURN
TIMER
REC
CANCEL
MUTE
ENTER
TRACKING
INDEX
EJECT
MENU
SPEEDPROGRAM
CALL
CLOSED
CAPTION
REC
REMOTE CONTROL
DESCRIPTION OF CONTROLS
17
22
16
19
21
23
24
25
27
20
1
2
3
4
5
6
8
10
12
14
15
7
1. CLOSED CAPTIONbutton-Switches betweenCaption, Text
and TV modes for Closed-Captioned programs.
2. Direct channel selection buttons (0–9) - Allows direct
access to any channel.
3. CALL button - Displays the present time/day of the week,
channel, counter, speed selection (and VCR mode if VCR
is operating) on the TV screen.
4. PROGRAM button - Press to confirm the programmed
timer recording and ON/OFF timer.
5. MENU button - Press to display the On-Screen menu
function.
6. DIGITAL TRACKING button - Allows automatic adjust-
ment of tracking to minimize picture noise during playback.
7. EJECT button - Press to eject the tape.
8. POWER button - Press to turn the TV/VCR on. Press
again to turn the TV/VCR off.
9. TV MONITOR button - Used to temporarily view a TV
channel selected on the VCR while in the playback mode.
10. SLEEP button - Sets the TV to turn off automatically after
up to 120 minutes.
11. CANCEL button - Used to clear the selected program or
the input data.
12. MUTE button - Press to turn off the sound. Press again to
turn the sound back on.
13. CHANNEL + / – and ▲ /▼ (cursor) buttons
CHANNEL + / – : Press the +button to change to a higher
numbered channel set into memory. Press the –button to
change to a lower numbered channel set into memory.
▲ /▼ (cursor) : Selects an item in the menu.
14. PAUSE/STILL button - During recording, this button
temporarily stops the tape. During playback, it stops the
tape and displays a still image on the TV screen.
15. FF (Fast Forward) button - In the Stop mode, this
button rapidly winds the tape forward. In the Play mode, this
button activates forward search.
16. INPUT SELECT button - Switches the program for viewing
between the TV/VCR and external input sources.
17. SPEED button - Sets the tape speed for recording.
18. REC and TIMER REC buttons
REC : Press both buttons at the same time once to start
normal recording. Additional presses activate One-touch
Timer Recording.
TIMER REC : Used to set the TV/VCR to start recording at
a preset time.
19. VOLUME + / – and B/A(cursor) buttons
VOLUME + / – : Press the +button to increase, or the –
button to decrease the volume level.
B/A(cursor) : Select an item or adjust the setting in the
menu.
20. INDEX + / – buttons - Search for the INDEX mark of a
tape.
21. REW (Rewind) button - In the Stop mode, this button
rapidly winds the tape backwards. In the Play mode, this
button activates reverse search.
22. SKIP SEARCH button - Press in the playback mode to
search forward in 30 second increments to a maximum of
3 minutes.
23. COUNTER RESET button - Used to reset the counter to
00:00:00.
24. CHANNEL RETURN button - Switchesbetween the present
channel and the last channel selected.
25. ZERO RETURN button - Use to stop the tape when the
counter reaches 00:00:00.
26. ENTER button - Press to enter or select information for
on-screen operations.
27. TRACKING + / – buttons - During playback, they are used
to adjust tracking manually.
28. PLAY button - Press to play a prerecorded tape.
29. STOP button - Press once to stop the tape.
9
11
26
18
13
28
29
5L80101C P01-09 20/4/04, 16:199

10
BATTERYINSTALLATION
BATTERYPRECAUTIONS
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g.Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (Follow battery
manufacturer’sdirections).
EFFECTIVE DISTANCE OF THE REMOTE CONTROL
REMOTE CONTROL (CONTINUED)
Install two “AAA” batteries,
paying attention to the
polarity diagram in the
battery compartment.
Slide the battery compart-
ment cover in the direction
of the arrow.
Replace the compartment
cover.
1
2
3
15 FEET
NOTES: •When there is an obstacle between the TV/VCR and the remote control, the remote control may not
operate.
•When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the
Remote sensor of the TV/VCR, the remote operation may be unstable.
•When using the remote control, press the button at intervals of about 1 second to ensure the correct
mode of operation.
5L80101C P10-19 20/4/04, 16:1910

11
ANT.
ANT.
ANT.
ANT.
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination VHF/
UHF antenna to the antenna jack.
If your combination VHF/UHF antenna has a 300 ohm
twin-lead wire, the use of the 300-75 ohm matching
transformer may be necessary.
75 ohm
coaxial
cable 300-75 ohm
matching
transformer
300-75 ohm
matching
transformer
UHF 300 ohm
VHF 300 ohm
UHF 300 ohm
VHF 75 ohm
Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300 ohm
twin-lead wire to the 300-75 ohm matching trans-
former. Attach the transformer to the combiner, then
attach the combiner to the antenna jack.
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner (not supplied). Attach
the combiner to the antenna jack.
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Antenna
jack Antenna jack
Antenna
jack
Combiner
Antenna
jack
Combiner
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna
system. If you are using a cable TV service (CABLE), see page 12 for Cable TV connections.
ANTENNA CONNECTIONS
5L80101C P10-19 20/4/04, 16:1911

12
This TV/VCR has an extended tuning range and can tune most cable channels without using a Cable TV
converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is gener-
ally provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a converter/descrambler box,
connect the Cable TV 75 ohm coaxial cable directly to the antenna
jack
on the back of the TV/VCR.
CABLE TV CONNECTIONS
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming
75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect the output jack
of the converter/descrambler box to the antenna jack on the TV/VCR. Follow the connections shown below. Set the
TV/VCR to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the converter/
descrambler box to select channels.
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
ANT.
75 ohm
coaxial cable
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B”
position, you can directly tune any nonscrambled channels on your TV/VCR. With the switch in the “A” position, tune
your TV/VCR to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/
descrambler box to tune scrambled channels.
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
Splitter B
A
Incoming
75 ohm
Cable TV cable A/B Switch
75 ohm cable
to TV/VCR
Incoming
75 ohm
Cable TV cable 75 ohm cable to
TV/VCR
Converter/
descrambler
Antenna
jack
Antenna
jack
Converter/
descrambler
ANT.
Antenna
jack
ANT.
5L80101C P10-19 20/4/04, 16:1912

13
CALL
PROGRAM SPEED
SLEEP
CANCEL
MUTE
POWER
CLOSED
CAPTION INPUT
SELECT
CHANNEL
RETURN
ZERO
RETURN
TIMER
REC
0
879
654
321
MENU ENTER
DIGITAL
TRACKING PAUSE
/STILL
TRACKING
INDEX
STOP
PLAY
FF
REW
COUNTER
RESET
TV MONITOR
SKIP
SEARCH
EJECT
VOL+
+
+
–
–
VOL–
CH–
CH+
REC
3
STARTING SETUP
The STARTING SETUP function makes installing your TV/VCR easily. It leads you the Language selection,
TV/CABLE selection, auto channel memory and auto clock setting automatically.
IMPORTANT: Make sure that the antenna or cable TV system connection is made!
Press ▲or ▼to select “TV” or “CABLE”,
then press ENTER.
4
Now the “AUTO CH MEMORY” starts.
After it completed the “AUTO CLOCK” starts
automatically.After the starting setup is com-
pleted, the TV channel appears on the screen.
Press ▲or ▼to select “START”, then press
ENTER.
If you select “CANCEL” and press ENTER, the
STARTING SETUP stops and changes to the TV
screen.
2
3
1
2
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
//
ENTER
><
CHANNEL PLAN
TV
CABLE
//
ENTER
><
AUTO SETUP
START
CANCEL
//
ENTER
><
AUTO CH MEMORY
STOP : CANCEL
AUTO CLOCK
STOP : CANCEL
A
1
1CANCEL
ENTER
ENTER
ENTER
Press POWER.
The starting setup function begins and the
Language setup menu appears on the screen.
Press ▲or ▼to select your desired language,
then press ENTER.
NOTES: • The starting setup function will work only when you press the POWER button for the first time.
• The auto clock function uses the EDS (Extended Data Service) information carried on the channel signal.
If the antenna signal is weak or there are no channels with EDS informations, the auto clock function may
not set the time. In this case you must set the clock manually (see page 17).
• In “AUTO CLOCK” setting, it may take more than 10 minutes to read the EDS signal for one
channel, which has only “Time of day” or “Local time zone”.
5L80101C P10-19 20/4/04, 16:1913

14
CALL
PROGRAM SPEED
SLEEP
CANCEL
MUTE
POWER
CLOSED
CAPTION INPUT
SELECT
CHANNEL
RETURN
ZERO
RETURN
TIMER
REC
0
879
654
321
MENU ENTER
DIGITAL
TRACKING PAUSE
/STILL
TRACKING
INDEX
STOP
PLAY
FF
REW
COUNTER
RESET
TV MONITOR
SKIP
SEARCH
EJECT
VOL+
+
+
–
–
VOL–
CH–
CH+
REC
3
SETTING THE LANGUAGE
Press MENU.
Press Bor Ato select option.
This TV/VCR can display the on screen language in English, Spanish or French.
Select the language you prefer first, then proceed with the other menu options.
Press ▲or ▼to select “LANGUAGE”, then
press A.
4
PressMENU repeatedly until theMENU screen
is cleared.
Press ▲or ▼to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press ENTER.
2
1 4
1
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
////
MENU
MENU
MENU
ENTER
LANGUAGE/
IDIOMA/LANGUE
PICTURE
PICTURE PREFERENCE
///
MENU
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
//
ENTER/MENU
1
32
3
2
5L80101C P10-19 20/4/04, 16:1914

15
AUTO CLOCK SETTING
The auto clock function will automatically set the built-in clock (Month, Day, Year and Time) when the TV/VCR is
connected to an antenna or cable TV system and it is turned off. As the TV/VCR searches for a receivable station
in your area and it receives a broadcast signal for auto clock, the auto clock needs several minutes to set itself.
AUTO CLOCK ADJUSTMENT
The auto clock adjustment will be performed at 12:00 PM everyday if you turn off the TV/VCR.
•If you use a cable box and you want auto clock adjustment to be performed, the cable box must be left on.
•The auto clock adjustment is not effective when there is a difference of more than 5 minutes exists between
the built-in clock time and the actual time.
TO SET AUTO CLOCK TO OFF
TO SET STANDARD TIME
In the rare event that you live within broadcast range of two stations in two different time zones, the TV/VCR may
recognize the wrong station for the auto clock set.
To correct the situation:
1. Press MENU.
2. Press Bor Ato select option.
3. Press ▲or ▼to select “STANDARD TIME”, then press A.
4. Press ▲/▼/B/Ato select your time zone, then press ENTER.
ATLANTIC : GMT – 4 hours (GMT: Greenwich Mean Time)
EASTERN : GMT – 5 hours
CENTRAL : GMT – 6 hours
MOUNTAIN : GMT – 7 hours
PACIFIC : GMT – 8 hours
ALASKA : GMT – 9 hours
HAWAII : GMT – 10 hours
AUTO : AUTO SET
5. Press MENU repeatedly until the menu screen is cleared.
NOTE: To be able to select the standard time, the clock must first be set by “AUTO CLOCK” once.
When shipped from factory the AUTO CLOCK option is set to “ON”.
But if you do not want Auto Clock set (Adjustment):
1. Turn on the TV/VCR.
2. Press MENU.
3. Press Bor Ato select option.
4. Press ▲or ▼to select “AUTO CLOCK”.
5. Press Bor Ato select “OFF”.
6. Press MENU repeatedly until the menu screen is cleared.
•When the “AUTO CLOCK” is set to “OFF”, the auto clock adjustment does not function.
•Set the clock manually (see page 17).
1. Connect the antenna or cable TV system.
•If you use a cable box, turn it on.
2. Plug the AC power cord to the AC outlet.
3. Make sure the TV/VCR is turned off.
•If you press POWER, the auto clock set is not effective.
4. Wait at least three minutes and press POWER.
5. Press CALL to check the clock on the screen.
6. If the clock is not set, check the antenna condition. The auto clock may not function properly if the reception
condition is not good.
AUTO CLOCK SETTING
5L80101C P10-19 20/4/04, 16:1915

16
CALL
PROGRAM SPEED
SLEEP
CANCEL
MUTE
POWER
CLOSED
CAPTION INPUT
SELECT
CHANNEL
RETURN
ZERO
RETURN
TIMER
REC
0
879
654
321
MENU ENTER
DIGITAL
TRACKING PAUSE
/STILL
TRACKING
INDEX
STOP
PLAY
FF
REW
COUNTER
RESET
TV MONITOR
SKIP
SEARCH
EJECT
VOL+
+
+
–
–
VOL–
CH–
CH+
REC
Press MENU. Press Bor Ato select option.
2
Press ▲or ▼to select “DAYLIGHT SAVING
TIME”, then press A.
NOTES: •When shipped from factory, “DAYLIGHT SAVING TIME” is set to “AUTO”.
•When the clock is not set, daylight saving time setting is not available.
•When there is no daylight saving time in your area, always select “OFF” in step 3.
3
Press the ▲or ▼to select one of the options, then press ENTER. Press MENU repeatedly until the
menu screen is cleared.
When you want to set the daylight saving time manually,
on the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
DAYLIGHT SAVING TIME SETTING
You can set the daylight saving time automatically or manually.
ON:
OFF:
AUTO:
for manual setting
(forward one hour)
for manual setting
(back one hour)
for automatic setting
(read EDS in the signal)
1 3
AUTO CLOCK SETTING (CONTINUED)
1
MENU
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
SAVING TIME
////
MENU
ON
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
SAVING TIME
///
MENU
ON
MENU
ENTER
1
3
2
3
DAYLIGHT SAVING TIME
ON
OFF
AUTO
//
ENTER/MENU
2
5L80101C P10-19 20/4/04, 16:1916

17
2
CALL
PROGRAM SPEED
SLEEP
CANCEL
MUTE
POWER
CLOSED
CAPTION INPUT
SELECT
CHANNEL
RETURN
ZERO
RETURN
TIMER
REC
0
879
654
321
MENU ENTER
DIGITAL
TRACKING PAUSE
/STILL
TRACKING
INDEX
STOP
PLAY
FF
REW
COUNTER
RESET
TV MONITOR
SKIP
SEARCH
EJECT
VOL+
+
+
–
–
VOL–
CH–
CH+
REC
4
MANUAL CLOCK SETTING
You must set the date and time manually for timer recordings, ON/OFF timer and daylight saving time if
the auto clock process did not set them correctly.
Press MENU.
Press Bor A to select option. Press ▲or ▼to select “CLOCK SET”, then
press A.
NOTES: •After a power failure or disconnection of the power plug, the time display will be lost. In this case, set the
present time again if the auto clock did not set correctly.
•To move cursor backward, press ▲.
3
8 : 30 AM SAT
EXAMPLE: Setting the clock to “8:30 AM”, 27th (SAT) March, 2004.
4
Press Bor Ato set the
month, then press ▼.Set the day, year and time
as in step 3, then press
ENTER.
After setting the clock, date and time
starts functioning automatically.
1
MENU
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
SAVING TIME
////
MENU
ON
CLOCK SET
ON/OFF TIMER
AUTO CLOCK
STANDARD TIME
DAYLIGHT
SAVING TIME
///
MENU
ON
CLOCK SET
MONTH
DAY
YEAR
TIME
ENTER/MENU
3
1(MON)
2004
12:00AM
////
CLOCK SET
MONTH
DAY
YEAR
TIME
ENTER/MENU
3
27(SAT)
2004
8:30AM
////
432
2
1
3
1
ENTER
5L80101C P10-19 20/4/04, 16:1917

18
CALL
PROGRAM SPEED
SLEEP
CANCEL
MUTE
POWER
CLOSED
CAPTION INPUT
SELECT
CHANNEL
RETURN
ZERO
RETURN
TIMER
REC
0
879
654
321
MENU ENTER
DIGITAL
TRACKING PAUSE
/STILL
TRACKING
INDEX
STOP
PLAY
FF
REW
COUNTER
RESET
TV MONITOR
SKIP
SEARCH
EJECT
VOL+
+
+
–
–
VOL–
CH–
CH+
REC
VHF/UHF/CABLE CHANNELS
CABLE
VHF
2-13
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
TV
VHF
2-13
UHF
14-69
Press Direct channel selection (0–9) to select the channel.
TV mode direct channel selection
When the TV/CABLE option is in the TV position, all channels can be instantly selected by using two buttons
(for example, to select channel 2, press “0”, then “2”. If you press only “2”, channel selection will be delayed for a few
seconds). For channels 10 and above, press the 2 digits in order.
CABLE mode direct channel selection
When the TV/CABLE option is in the CABLE position, channels can be selected as follows:
TO SELECT CABLE CHANNELS:
1-9 Press “0” twice, then 1-9 as needed. Example, to select channel 2, press “002”.
10-12 Press “0”, then the remaining 2 digits. Example, to select channel 12, press “012”.
13-99 Press the 2 digits in order. Example, to select channel 36, press “36”.
100-125 Press the 3 digits in order. Example, to select channel 120, press “120”.
TV OPERATION
NOTES: •If a channel with no broadcast is selected, the sound will automatically be muted.
•If a station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.
To turn on the TV/VCR,
press POWER.Adjust the volume level by
pressing VOL + or –.
The volume level will be
indicated on the screen by green
bars. As the volume level increases,
so do the number of bars. If the
volume decreases, the number of
green bars also decreases.
Set the TV/CABLE selection
to the appropriate position
(see page 22).
TV - VHF/UHF Channels
CABLE - Cable TV Channels
VOLUME 22
3
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding channel will be selected in 2 seconds.
CH 012
2
4
1
2
0 1 2
VOL – VOL +
1
4
5L80101C P10-19 20/4/04, 16:2018