TP-Link TL- WR740N User manual

TP-Link TL- WR740N/ WR741ND User Guide
Contents
1 Main Features
2 The Front Pane
of the modem
3 Back Pane
4 How to setup/connect your hardware
5 Quick Insta ation Guide

Main Features
Make use of IEEE 802.11n wireless technology to provide a wireless data rate of
up to 150M ps
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation
RJ45 LAN ports, supporting Auto MDI/MDIX
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES
encryption security
Shares data and Internet access for users, supporting Dynamic IP/Static
IP/PPPoE Internet access
Supports Virtual Server, Special Application and DMZ host
Supports UPnP, Dynamic DNS, Static Routing
Provides Automatic-connection and Scheduled Connection on certain time to the
Internet
Connects Internet on demand and disconnects from the Internet when idle for
PPPoE
Built-in NAT and DHCP server supporting static IP address distri uting
Supports Stateful Packet Inspection
Supports VPN Passthrough
Supports Parental Control and Access Control
Provides 64/128/152- it WEP encryption security and wireless LAN ACL (Access
Control List)
Supports Flow Statistics
Supports firmware upgrade and We management
Provide a switch for the power

The Front Pane of the modem
Following indicates the status of the LED lights which provides you the modem’s
working status.
Back Pane

RESET: There are two ways to reset to the Router's factory defaults.
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
Router's We - ased Utility.
2) Use the Factory Default Reset utton: Press the Reset utton for five seconds and then
wait for the Router to re oot.
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WR740N/TL-WR741ND 150M ps Wireless N
Router.
ON/OFF: The switch for the power.
1,2,3,4 (LAN): These ports (1, 2, 3, 4) connect the Router to the local PC(s).
WAN: This WAN port is where you will connect the DSL/ca le Modem, or
Ethernet.
Wire ess antenna: To receive and transmit the wireless data.
QSS: If you have client devices, such as wireless adapters, that support
Wi-Fi Protected Setup, then you can press this utton to quickly esta lish a
connection etween the Router and client devices and automatically
configure wireless security for your wireless network.
How to setup/connect your hardware

Quick Insta ation Guide
To access the we configuration utility for the router, open a we - rowser and type in the default
address 192.168.1.1 in the address field of the rowser.
If 192.168.1.1 is not responding try 192.168.0.1.
After sometime, you will e prompted to enter the modem User Name and Password for the
modem to login. By default it is ‘admin’ for oth. Then click the OK utton or press the Enter
key.
1. After successfully login, you can click the Quick Setup to quickly configure your
Router.

2. Click Next and then WAN Connection Type page will appear. Select the WAN
Connection Type as PPPoE.
3. Configure the following options provided y your ISP: Username, Password. Then
click Next.
4. If you are visiting the Router from the main computer, please select Yes, and then
click C one MAC Address.

5. Click Next to continue, the Wire ess settings page will appear. Select Wire ess
Security as WPA-Persona /WPA2-Persona and enter the wireless password in

password field.
6. Click the Next utton. You will then see the Finish page.

7. If there is something changed on the Wireless page, you will see the Finish page as
shown elow. Click the Reboot utton to make your wireless configuration take effect
and finish the Quick Setup.