Transonic TC2078HS User manual

Please read these instructions carefully and retain for future reference

1
10

CHARACTERISTICS
Real 5.1-channel, supports EAX, AC-3 and compatible with DVD CD/VCD,
MP3, PC, etc.
Easy operations by remote control .
Separate control of each channel and good sound effect.
SPECIFICATIONS
Power Audio: 10W x 5 +25W (RMS)
Drive Units: 3" x 5 full range magnetically shielded + 5.25" subwoofer
Frequency Response: Satellites: 120Hz-20KHz
Subwoofer:20Hz-170Hz
Separation: 40 dB
S/N: 70dB
Distortion: =0.5%(1K, 1W)
Power Supply: AC230V, 50Hz
Dimensions: Satellites: W104 x H138 XD104 (mm)
Subwoofer: W160 x H300 XD343 (mm)
Weight: 6.5 Kg
Design and specifications are subject to modification without prior notice
9
V

INSTALLATION
1.Connect all satellite speaker cables respectively (FL, FR ,SL, SR ,CEN) into
right sockets located at the rear side of subwoofer (FL: left front speak-
er; FR: right front speaker, SL: surround left speaker, SR:surround ri-
ght speaker; CEN; center speaker.)
2.For a 5.1 channel sound source connected, to link outpu t signal of
(DVD Ac3 sound card etc) with the FL, FR, SL, SR, CEN. signal input
port respectively.
3.For the tridimensional information, please insert audio line into AUX
input jack.
4. After a correct connection, to insert the power plug into the wall outlet
of AC 230V / 50 Hz
appliance
appliance.
appliance

1.SPKR LED LIGHT
2.MAST LED LIGHT
3.FRONT LED LIGHT
4.SW LED LIGHT
5.SURROUND LED LIGHT
6.CENTER LED LIGHT
7.STAND BY
8.SOURCE
9.SPKR
10.SELECT
11.VOL+
12. VOL-
Front view of woofer
Subwoofer 1 pc
Satellite Speaker 5 pcs
Audio Input Cord 3 pcs
Remote control 1 pc
Batteries(for remote control) 2 pc
Instruction Manual 1 pc
CONTENTS
FRONT PANEL
STAND BY
SOURCE
SPKR
SELECT
VOL+
VOL-
REMOTE OPRATION EXPLAIN
1.According to linkedpicture, Connect machine (DVD,VCD,PC and so
on) with Subwooferand speakers accordingly.
2.
3.Press STAND BY key of thepanel, you can hear the sound of
absorbing and Combiningin the machine. At the same time, the
numeral tube ofthe panel will go on, then the AudioSystem enter
into the stateof working and the Volume is 30 , If press STAND
BY again, then enterinto STAND By .
4.Press SOURCE to convert 2.0channel input to 5.1 channel .
5.Press SPKR to convert 2.1channel output to 5.1 channel .
6.Press MASTER+/- to increase ordecrease the volume. At the
same time 4pcsof LED will go on. When the volume' s numeral
is 60 , which meansthe volume is maximum . When the volume' s
numeral is 0 , which meansthe volume is minimum .
7.
8.Press MUTE of remote controlto disable the sound temporality, at
the same timethe numeral tube will flash. Press MUTE again, to
enable sound.
9.If RESET of remote control,the machine will resume the primary
state.
Switch on PowerSupply, then the number is -- of numeral tube
on the frontpanel.
Press SELECT key, the green LED of FRONT\CENTER\
SURROUND\SW Will gooff vicissitudinary. At the Same time,press
VOL+/- to increase ordecrease every channel's volume. The number
of numeral tubewill change accordingly.

REAR PANEL
1. AUX input
2. FL&FR input
3. CEN/SW input
4. SL&SR input
5. FR output
6. FL output
7. SR output
8. SL output
9. CEN output
10. AC power supply line input
11. Power on-off
Back view of woofer
1
2
3
4
5
6
7
8
9
~230v/50Hz
REMOTE CONTROL KEYS
1.ST-BY
2.MUTE
3.SPKR
4.SOURCE
5.RESET
6.FRONT+
7.FRONT-
8.CEN+
9.CEN-
10.SUR+
11.SUR-
12.SW+
13.SW-
14.MASTER+
15.MASTER-
FRONT PANEL OPERATION EXPLAIN
1.According to linked picture, Connect machine (DVD,VCD,PC and so
on) with Subwoofer and speakers accordingly.
2.Switch on Power Supply, then the number is -- of numeral tube
on the front panel.
3.Press STAND BY key of the panel, you can hear the sound of
absorbing and Combining in the machine. At the same time, the
numeral tube of the panel will go on, then the Audio System enter
into the state of working and the Volume is 30 , If press STAND
BY again, then enter into STAND By .
4.Press SOURCE to convert 2.0 channel input to 5.1 channel .
5.Press SPKR to convert 2.1 channel output to 5.1 channel .
6.Press VOL+/- to increase or decrease the volume. When the
volume' s numeral is 60 , which means the volume is maximum .
When the volume' s numeral is 0 , which means the volume is
minimum .
7.Press SELECT key, the green LED of FRONT\CENTER\
SURROUND\SW Will go off vicissitudinary. At the Same time, p-
ress VOL+/- to increase or decrease every channel's volume.
The number of numeral tube will change accordingly.
TC2078HS